反应详情

In 30 mL of MeCN, 5.99 g of Z-Phe was dissolved, and 3.94 g of HONB and 4.59 g of WSCD HCl were added to the solution at 0° C., followed by stirring at room temperature for 4 hours. While keeping at 0° C., 3.4 mL of 25% NH3 aq. solution and 10 mL of DMF were added to the mixture, followed by stirring for 4 hours. After the solvent was distilled off, the residue was dissolved in AcOEt and the solution was washed with 1N HCl aq. solution, satd. NaHCO3 aq. solution and then satd. NaCl aq. solution. After drying over Na2SO4, the solvent was concentrated and diethyl ether was added to give 1.48 g of Z-Phe-NH2 as precipitates (yield 99%). After 1.94 g of [Bis(trifluoroacetoxy)iodo]benzene was dissolved in 20 mL of MeCN and 5 mL of H2O, 890 mg of Z-Phe-NH2 prepared above and 972 μL of pyridine were added to the precipitate at 0° C., and the mixture was stirred at room temperature for 15 hours. After the solvent was concentrated, the concentrate was subjected to liquid-liquid separation with diethyl ether-1N HCl aq. solution. The 1N HCl aq. solution layer was concentrated and then dried. A half volume of the concentrate was dissolved in 5 mL of DMF, and 486 μL of mono-tert-butyl malonate and 540 mg of HOBt were added to the solution. Then, 2.08 g of PyBOP and 1394 μL of DIEA were added to the mixture at 0° C., followed by stirring at room temperature for 15 hours. The solvent was distilled off, the residue was dissolved in AcOEt and the solution was washed with 1N HCl aq. solution, satd. NaHCO3 aq. solution and then satd. NaCl aq. solution. After drying over Na2SO4, the solvent was concentrated and the concentrate was purified by flush column chromatography. Diethyl ether-petroleum ether was added to give 304 mg (yield 33%) of Z-PheΨ(NHCO)Gly-OBut as precipitates. After 154 mg of the product was dissolved in 20 mL of MeOH, 10% Pd—C was added to the solution, followed by catalytic hydrogenation for 2 hours in a hydrogen flow. After removal of the catalyst by filtration, the solvent was concentrated and dried. The residue was dissolved in 10 mL of MeCN 10 mL and 152 mg of Fmoc-OSu and 78 μL of DIEA were added to the solution, followed by stirring for 15 hours. After the solvent was distilled off, the residue was dissolved in AcOEt and the solution was washed with 1N HCl aq. solution, satd. NaHCO3 aq. solution and then satd. NaCl aq. solution. After drying over Na2SO4, the solvent was concentrated and diethyl ether-petroleum ether was added to give 127 mg of Fmoc-PheΨ(NHCO)Gly-OBut as precipitates (yield 68%). Fmoc-Leu was introduced into 63 mg of Fmoc-Arg(Boc2,Me)Phe-Rink Amide MBHA resin prepared in EXAMPLE 10. Following Fmoc deprotection, Fmoc-PheΨ(NHCO)Gly-OH (prepared by treating 25 mg of Fmoc-PheΨ(NHCO)Gly-OBut with TFA for 3 minutes), 300 μL of 0.5M HOAt, 78 mg of PyAOP and 52 μL of DIEA were added to the resin, and the mixture was shaken for 6 hours. After washing the resin, 2 mL of DMF, 9 μL of DIEA and 12 μL of Ac2O were added to the resin, and the mixture was shaken for 30 minutes. After washing the resin, the peptide chain was extended on ABI 433A to give Boc-D-Tyr(But)Asn(Trt)Trp(Boc)Asn(Trt)Ser(But)Phe‥(NHCO)GlyLeuArg(Boc2 μM e)Phe-Rink Amide MBHA resin. To 34 mg of the product, 200 μL of TFA/PhSMe/m-cresol/TIS/EDT (85/5/5/2.5/2.5) was added, and the mixture was stirred for 2 hours. Ether was added to the reaction solution. The resulting precipitate was centrifuged and the supernatant was removed. This procedure was repeated for washing. The residue was extracted with an aqueous acetic acid solution and the extract was filtered to remove the resin. Linear density gradient elution (60 minutes) was then performed with eluants A/B:76/24-66/34 using: 0.1% TFA in water and eluant B: 0.1% TFA-containing acetonitrile on preparative HPLC using YMC D-ODS-5-ST S-5 120A column (20×150 mm). The fractions containing the product were collected and lyophilized to give 0.7 mg of white powders.

1. customWhile keeping at 0° C.
2. stirringby stirring for 4 hours
3. distillationAfter the solvent was distilled off
4. dissolutionthe residue was dissolved in AcOEt
5. washthe solution was washed with 1N HCl aq. solution
6. dry with materialAfter drying over Na2SO4
7. concentrationthe solvent was concentrated
8. additiondiethyl ether was added