StartseiteMCPWorkbenchSkills
StartseiteWorkbenchBenachrichtigungenMein Bereich
llms.txt · MCP-AnleitungDatenschutz · Nutzungsbedingungen · Supportv1.8.0
  1. Startseite
  2. /Verbindung

3-Bromtoluol

3-Bromotoluene

HCID 11560
Neue NotizNeue ReaktionAnfrage stellen
Druckvorschau
GrundinformationenÜberblickNamen und BezeichnerEigenschaftenSicherheit und RegulatorischesChemie und IndustrieZugehörige ReaktionenNotizen zur Verbindung
TeilstruktursucheÄhnliche Strukturen suchen

Grundinformationen

CAS
591-17-3
Standard-SMILES
Cc1cccc(Br)c1
InChIKey
WJIFKOVZNJTSGO-UHFFFAOYSA-N
Summenformel
C7H7Br
Durchschnittliche Molmasse
171,03 g/mol
Monoisotopische Masse
169,97311232

Überblick

M-bromotoluene is a clear colorless liquid. (NTP, 1992)

Namen und Bezeichner

Bevorzugter Name
3-Bromotoluene
IUPAC
1-bromo-3-methylbenzene
Lokaler Name
3-Bromtoluol
Englischer Name
3-Bromotoluene
Summenformel
C7H7Br
Molmasse
171.03

Namen und Synonyme

3-BROMOTOLUENE591-17-31-Bromo-3-methylbenzenem-Bromotoluenem-Tolyl bromide3-MethylbromobenzeneBenzene, 1-bromo-3-methyl-5-Bromotoluene3-Bromo-1-methylbenzeneToluene, m-bromo-3-Methyl-1-bromobenzenem-Methylbromobenzene
Weitere Namen anzeigen
META-BROMOTOLUENE3-BromotoL3-Bromtoluol3-Bromotolune3-bromo-toluen3-Tolylbromidem-bromo-toluen
Toluene, 3-bromo-3-methylphenyl bromideCCRIS 5981DTXSID3024659HSDB 60143-tolyl bromideEINECS 209-702-3BRN 1903633

Datenbank-Bezeichner

CAS
591-17-3
PubChem CID
11560
DTXSID
DTXSID3024659
ChEMBL
CHEMBL1538200
UNII
9426O61G73
EC Number
209-702-3
Nikkaji
J47.829F

Eigenschaften

Berechnete Struktureigenschaften

XLogP
3,3
Polarare Oberfläche (TPSA)
0 Ų
H-Brücken-Donoren
0
H-Brücken-Akzeptoren
0
Frei drehbare Bindungen
0
Schwere Atome
8
Formalladung
0
Komplexität
70,8

Experimentelle und physikochemische Eigenschaften

SolventsSolvents -> Brominated Solvents
SpringerMaterials Properties13C nuclear magnetic resonance spectrum
LogPlog Kow = 3.41
Density · 2 Einträge

1.41 at 68 °F (NTP, 1992) - Denser than water; will sink

1.4099 at 20 °C/4 °C

Color/FormLIQUID
Solubility · 4 Einträge

less than 1 mg/mL at 68 °F (NTP, 1992)

Sol in chloroform

Soluble in ethanol and acetone, miscible in ether

Water solubility = 51.3 mg/l

Flash Point · 2 Einträge

140 °F (NTP, 1992)

60 °C

Boiling Point · 2 Einträge

362.7 °F at 760 mmHg (NTP, 1992)

183.7 °C at 760 mm Hg

Melting Point · 2 Einträge

-40 °F (NTP, 1992)

Sicherheit und Regulatorisches

Sicherheitsangaben dienen nur zur Orientierung und ersetzen weder das Sicherheitsdatenblatt (SDB) des Lieferanten noch geltende Vorschriften oder eine fachliche Bewertung.

GHS-Klassifizierung

GHS Classification · 4 Einträge

Warning

H226 (84%): Flammable liquid and vapor [Warning Flammable liquids]

P210, P233, P240, P241, P242, P243, P261, P264, P264+P265, P270, P271, P280, P301+P317, P302+P352, P303+P361+P353, P304+P340, P305+P351+P338, P319, P321, P330, P332+P317, P337+P317, P362+P364, P370+P378, P403+P233, P403+P235, P405, and P501 (click each P-code to see the statement)

Aggregated GHS information provided per 50 reports by companies from 10 notifications to the ECHA C&L Inventory. Each notification may be associated with multiple companies.

Gefahrenhinweise

Regulatory Information · 2 Einträge

Chemical: Benzene, 1-bromo-3-methyl-

3-Bromotoluene: Does not have an individual approval but may be used under an appropriate group standard

DOT LabelFlammable Liquid Poison
Fire HazardsThis chemical is combustible. (NTP, 1992)
Health HazardsSYMPTOMS: Symptoms of exposure to this compound include eye and skin irritation.
Hazards Summary · 2 Einträge

Irritant; [HSDB] An irritant; Inhalation of high concentrations can cause CNS depression; [MSDSonline]

The major hazards encountered in the use and handling of 3-bromotoluene stem from its toxicologic properties. Exposure to 3-bromotoluene may occur through inhalation or dermal contact at sites where the substance is manufactured, used as a solvent, or used as a chemical intermediate. This substance has the potential to cause respiratory irritation and CNS depression. Entry into contaminated areas warrants the wearing of a full-face mask, self-contained breathing apparatus which provides eye protection. This substance is normally stable, even under fire conditions; requiring moderate heating before ignition will occur. Normal procedures may be used to fight a 3-bromotoluene fire; using water to blanket the fire. Before transporting 3-bromotoluene, the regulatory requirements of the DOT must be consulted. Prior to implementing land disposal of waste residue (including waste sludge), consult with environmental regulatory agencies for guidance.

Chemie und Industrie

Verwendung und Herstellung

Uses · 5 Einträge

Used as a solvent for fats, waxes, and resins; Also used as an intermediate and research chemical; [HSDB]

RESEARCH CHEMICAL

3-Bromotoluene is used as a solvent (for fats, waxes or resins, and as a medium for carrying out reactions) and as a chemical intermediate.

Chemical synthesis

1.53 mm Hg @ 25 °C /calculated from experimentally derived coefficients/

Methods of Manufacturing · 2 Einträge

... BY DIAZOTIZATION OF M-TOLUIDINE FOLLOWED BY TREATMENT WITH CUPROUS BROMIDE, POTASSIUM BROMIDE, & HYDROBROMIC ACID. BY HEATING A MIXT OF TOLUENE & P-BROMO-PHENOL WITH ALUMINUM TRICHLORIDE (ALCL3). BY ELIMINATION OF THE AMINO GROUP FROM 4-AMINO-3-BROMO-TOLUENE.

Replacement of hydrogen in parent compound by bromine: (a) in the presence of iron; ... Hydrogen bromide is allowed to escape, preferably being washed by incoming raw material. In some cases a method for separating isomeric compounds is necessary.

General Manufacturing InformationBenzene, 1-bromo-3-methyl-: ACTIVE
Anwendungen · 1 Eintrag

Verwenden3-Bromotoluene was used in the precise determination of bromine isotope ratio in organic compounds by MC-ICPMS ( Multicollector-Inductively Coupled Plasma Mass Spectrometer). It undergoes palladium-catalyzed cyanation reaction in the presence of K4[Fe(CN)6] as the cyanide surrogate. It also undergoes palladium-catalyzed reaction with alkynyltriarylborates to yield trisubstituted alkenylboranes.

Darstellung · 1 Eintrag

synthetischeSynthesis of 3-Bromotoluene: It is derived from 3-bromo-4-aminotoluene by diazotization and reduction. The mixture of 95% ethanol, concentrated sulfuric acid and 3-bromo-4-aminotoluene was stirred and cooled to 10°C, and sodium nitrite solution was added to keep the reaction temperature not exceeding 10°C. After adding, continue stirring for 20min. Add the copper powder washed with ether, heat carefully, stop heating after the reaction starts, nitrogen will be released violently, and acetaldehyde will be formed. Then steam distillation is carried out until no oily substance evaporates. Separate the organic phase from the distillate and wash with 10% sodium hydroxide, water, concentrated sulfuric acid, and 5% sodium carbonate solution in sequence. Dry with anhydrous calcium chloride, filter, distill, collect 180-183 ℃ (99.75kPa) fractions to obtain colorless pure 3-bromotoluene with a yield of over 50%.

Zugehörige Reaktionen

179
Reaktionsaufzeichnung erstellen
Reaktionsgleichung von HRID 80080
HRID 80080als Eduktuspto-grants-2014_09
Reaktionsgleichung von HRID 91021
HRID 91021als EduktTraining data from https://doi.org/10.1039/C8SC04228D (2/10)
Reaktionsgleichung von HRID 94438
HRID 94438als EduktTraining data from https://doi.org/10.1039/C8SC04228D (2/10)
Reaktionsgleichung von HRID 119167
HRID 119167als EduktTraining data from https://doi.org/10.1039/C8SC04228D (2/10)
Reaktionsgleichung von HRID 121620
HRID 121620als EduktTraining data from https://doi.org/10.1039/C8SC04228D (2/10)
Reaktionsgleichung von HRID 123047
HRID 123047als EduktTraining data from https://doi.org/10.1039/C8SC04228D (2/10)
Reaktionsgleichung von HRID 126862
HRID 126862als Eduktuspto-grants-1981_03
Reaktionsgleichung von HRID 157752
HRID 157752als EduktTraining data from https://doi.org/10.1039/C8SC04228D (9/10)
Seite 1 von 23

Notizen zur Verbindung

Wird geladen…

Auf dieser SeiteGrundinformationenÜberblickNamen und BezeichnerEigenschaftenSicherheit und RegulatorischesChemie und IndustrieZugehörige ReaktionenNotizen zur Verbindung
Weitere Aktionen
Neue NotizNeue ReaktionAnfrage stellen

-39.8 °C

Vapor Pressure · 3 Einträge

1 mmHg at 58.6 °F (NTP, 1992)

1.53 [mmHg]

Vapor pressure = 0.145 kPa (1.09 mm Hg) at 25 °C

Refractive IndexIndex of refraction: 1.5510 at 20 °C/D
Heat of Vaporization10,537.1 gcal/gmole

Physikochemische Eigenschaften

Schmelzpunkt
-40 °C · -40 °C
Siedepunkt
183.7 °C · 183.7 °C(lit.)
Dichte
1.41 g/mL · 1.41 g/mL at 25 °C(lit.)
Dampfdruck
2.04 hPa · 2.04 hPa ( 25 °C)
Brechungsindex
20 · n20/D 1.552(lit.)
Flammpunkt
140 °F · 140 °F
storage temp.
30 °C · Store below +30°C.
Löslichkeit
0.05 g/l · 0.05g/l
Aggregatzustand
Liquid
Wichte
1.41 · 1.410
Farbe
Clear colorless to light yellow
Wasserlöslichkeit
insoluble
Merck
14 · 14,1439
BRN
1903633 · 1903633
Henry's Law Constant
1.5 · 1.5×10-3 mol/(m3Pa) at 25℃, Duchowicz et al. (2020)
Dielectric constant
5.36 · 5.3600000000000003
InChI
1S/C7H7Br/c1-6-3-2-4-7(8)5-6/h2-5H,1H3
InChIKey
WJIFKOVZNJTSGO-UHFFFAOYSA-N
SMILES
Cc1cccc(Br)c1
CAS Datenbank
591 · 591-17-3(CAS DataBase Reference)
NIST chemische Informationen
1 · Benzene, 1-bromo-3-methyl-(591-17-3)
EPA chemische Informationen
m-Bromotoluene (591-17-3)
Reactive GroupAryl Halides
Reactivity AlertsHighly Flammable
Reactivity ProfileM-BROMOTOLUENE is incompatible with strong oxidizing agents. (NTP, 1992)
Air and Water ReactionsHighly flammable. Insoluble in water.
Hazard Classes and CategoriesFlam. Liq. 3 (84%)
Skin, Eye, and Respiratory IrritationsIrritant

Sicherheit und Schutzausrüstung

Fire FightingFires involving this material can be controlled with a dry chemical, carbon dioxide or Halon extinguisher. (NTP, 1992)
First Aid · 1 Eintrag

EYES: First check the victim for contact lenses and remove if present. Flush victim's eyes with water or normal saline solution for 20 to 30 minutes while simultaneously calling a hospital or poison control center. Do not put any ointments, oils, or medication in the victim's eyes without specific instructions from a physician. IMMEDIATELY transport the victim after flushing eyes to a hospital even if no symptoms (such as redness or irritation) develop.

Nonfire Spill Response · 1 Eintrag

SMALL SPILLS AND LEAKAGE: If you spill this chemical, FIRST REMOVE ALL SOURCES OF IGNITION. Then, use absorbent paper to pick up all liquid spill material. Your contaminated clothing and absorbent paper should be sealed in a vapor-tight plastic bag for eventual disposal. Solvent wash all contaminated surfaces with 60-70% ethanol followed by washing with a soap and water solution. Do not reenter the contaminated area until the Safety Officer (or other responsible person) has verified that the area has been properly cleaned.

Disposal Methods · 1 Eintrag

SRP: At the time of review, criteria for land treatment or burial (sanitary landfill) disposal practices are subject to significant revision. Prior to implementing land disposal of waste residue (including waste sludge), consult with environmental regulatory agencies for guidance on acceptable disposal practices.

Preventive Measures · 1 Eintrag

SRP: The scientific literature for the use of contact lenses in industry is conflicting. The benefit or detrimental effects of wearing contact lenses depend not only upon the substance, but also on factors including the form of the substance, characteristics and duration of the exposure, the uses of other eye protection equipment, and the hygiene of the lenses. However, there may be individual substances whose irritating or corrosive properties are such that the wearing of contact lenses would be harmful to the eye. In those specific cases, contact lenses should not be worn. In any event, the usual eye protection equipment should be worn even when contact lenses are in place.

Isolation and EvacuationExcerpt from ERG Guide 131 [Flammable Liquids - Toxic]:
Personal Protective Equipment (PPE) · 1 Eintrag

RECOMMENDED RESPIRATOR: Where the neat test chemical is weighed and diluted, wear a NIOSH-approved half face respirator equipped with an organic vapor/acid gas cartridge (specific for organic vapors, HCl, acid gas and SO2) with a dust/mist filter. (NTP, 1992)

Toxikologische Informationen

Environmental Fate · 3 Einträge

TERRESTRIAL FATE: Based on a recommended classification scheme(1), an estimated Koc value of 434(SRC), derived from a molecular structure estimation method(2), suggests that 3-bromotoluene will have moderate mobility in soil(SRC). Its high Henry's Law constant, 6.71X10-3 atm-cu m/mole(SRC), estimated from its water solubility(3), high vapor pressure, 1.53 mm Hg at 25 °C(5), and moderate adsorptivity to soil suggests that volatilization may be an important fate process from both moist and dry soil surfaces(4,SRC). Experimental data suggests that 3-bromotoluene may be subject to direct photolysis on the soil surface(6). 3-Bromotoluene's potential for biodegradation in soil is unknown(SRC).

AQUATIC FATE: Based on a recommended classification scheme(1), an estimated Koc value of 430(SRC) determined from molecular structure(2), indicates that 3-bromotoluene may adsorb to sediment and particulate matter in the water column(SRC). It is expected to readily volatilize from water based on its Henry's Law constant of 6.7X10-3 atm-cu m/mole(SRC), estimated from its water solubility(3) and vapor pressure(7). Estimated half-lives for a model river and model lake are 4.0 hours and 5.2 days, respectively(4,SRC). Using a model which takes adsorption into account(7), the volatilization half-life of 3-bromotoluene in an environmental pond is estimated to be 14.9 days. According to a recommended classification scheme(6), an estimated BCF value of 230(4,SRC), based on its log Kow(5,SRC), suggests that bioconcentration in aquatic organisms will be moderately high(SRC).

ATMOSPHERIC FATE: According to a theory of gas/particle partitioning of semivolatile organic compounds in the atmosphere(1), 3-bromotoluene, which has a vapor pressure of 1.53 mm Hg at 25 °C(2) will exist as a vapor in the ambient atmosphere(SRC). Vapor-phase 3-bromotoluene degrades in the atmosphere by reaction with photochemically-produced hydroxyl radicals; the half-life for this reaction is estimated to be 4.8 days(3,SRC).

Adverse EffectsNeurotoxin - Acute solvent syndrome
Soil Adsorption/Mobility · 1 Eintrag

Using an estimation method based on molecular connectivity indices(1), the Koc for 3-bromotoluene is estimated to be 430(SRC). According to a suggested classification scheme(2), this Koc value suggests that 3-bromotoluene will have medium mobility in soil(SRC).

Artificial Pollution Sources3-Bromotoluene's production and use as a solvent(1) and chemical intermediate(2) may result in its release to the environment through various waste streams(SRC).
Environmental Bioconcentration · 1 Eintrag

A BCF of 230 was estimated for 3-bromotoluene(SRC), using its log Kow of 3.41(1,SRC), and a recommended regression-derived equation(2). According to a recommended classification scheme(3), this BCF value suggests that 3-bromotoluene has a moderately high potential for bioconcentration in fish and aquatic organisms(SRC).

Volatilization from Water/Soil · 1 Eintrag

The Henry's Law constant of 3-bromotoluene calculated from its vapor pressure, 1.53 mm Hg at 25 °C(3), and water solubility, 513 mg/l(1), is 6.7X10-3 atm-cu m/mole(SRC), which indicates that volatilization from environmental waters is probably significant, and may be rapid(2). The volatilization half-life of 3-bromotoluene from a model river (1 meter deep flowing 1 m/sec with a wind speed of 3 m/sec) and model lake (1 meter deep flowing at 0.05 m/sec with a wind speed of 0.5 m/sec) is estimated to be 4.0 hr and 5.2 days, respectively(2,SRC); these estimates do not consider the effect of adsorption to sediment which may be important(SRC). The volatilization half-life of 3-bromotoluene in an environmental pond which considers adsorption is estimated to be 14.9 days(4,SRC).

Non-Human Toxicity Excerpts · 2 Einträge

RESPIRATORY IRRITATION &, IN HIGH CONCN ... /CNS DEPRESSION/ IN EXPTL ANIMALS.

m-Bromotoluene tested negative for mutagenicity in Salmonella assays.

Environmental Abiotic Degradation · 1 Eintrag

The rate constant for the vapor-phase reaction of 3-bromotoluene with photochemically-produced hydroxyl radicals is estimated to be 3.34X10-12 cu m/molecule-sec at 25 °C(1,SRC). Assuming an average atmospheric hydroxyl radical concn of 5X10+5 molecules/cu cm, the half-life for this reaction is estimated to be 4.8 days(1,SRC). 3-Bromotoluene does not contain any functional groups that are susceptible to hydrolysis(2); therefore, hydrolysis is not expected to be significant in natural waters(SRC). Irradiation of 3-bromotoluene (in hexane solution) with artificial UV light above 290 nm resulted in a dehalogenation of 0.36% over a two hour period(3).

Probable Routes of Human ExposureOccupational exposure may occur through inhalation or dermal contact at sites where 3-bromotoluene is manufactured, used as a solvent, or used as chemical intermediate. (SRC)
Environmental Fate/Exposure Summary · 1 Eintrag

3-Bromotoluene may be released to the environment through evaporation from solvent uses or in waste streams generated at sites of production and use. If released to the atmosphere, 3-bromotoluene is expected to degrade by reaction with photochemically-produced hydroxyl radicals; the half-life for this reaction is estimated to be 4.8 days. If released to water, 3-bromotoluene may be removed from the water column by volatilization and adsorption. Using an estimated Henry's Law constant of 6.7X10-3 atm-cu m/mol, volatilization half-lives of 4.1 hr and 5.2 days are estimated for a model river and model lake, respectively. The effect of adsorption to sediment is considered in the estimated volatilization half-life of 14.9 days from an environmental pond, but not from the model river or model lake. An estimated Koc value of 430 suggests that if 3-bromotoluene is released to soil, moderate leaching may occur. Based on its estimated Henry's Law constant and measured vapor pressure (1.53 mm Hg at 25 °C), evaporation from dry and moist soil surfaces may also occur. Data are not available with which to assess the importance of biodegradation in the environment. Ot's estimated BCF of 230 suggests that there is a moderately high potential for bioconcentration in aquatic organisms. Occupational exposure may occur through inhalation or dermal contact at sites where 3-bromotoluene is manufactured, used as a solvent or used as a chemical intermediate. (SRC)

Toxicity DataLC50 (rat) = 6800 mg/m3

Sicherheitsdaten

F
8
wgk
3
tsca
TSCA listed
ridadr
UN 1993 3/PG 3
hs_code
29036990
RTECS-Nr.
XS7965400
risk_code
22-36/37/38
hazard_code
Xn,Xi
hazard_note
Harmful/Irritant
safety_code
26-36-37/39
hazard_class
3
Speicherklasse
3 - Flammable liquids
Giftige Stoffe Daten
591-17-3(Hazardous Substances Data)
Hazard Classifications
Acute Tox. 3 InhalationAcute Tox. 4 OralEye Irrit. 2Flam. Liq. 3Skin Irrit. 2STOT SE 3

Vor- und nachgelagerte Produkte

Vorgelagerte Rohstoffe

2-Brom-p-toluidinKupferEthanol

Nachgelagerte Produkte

tert-Butyl 4-(3-formylbenzyl)tetrahydro-1(2H)-pyrazinecarboxylate3-BrombenzoesureTris(3-methylphenyl)phosphin3-(Ethyl(methyl)carbamoyl)phenylboronic acid3-(Dimethylcarbamoyl)phenylboronic acid3-Ethynyltoluene5-Bromo-2-chlorotoluene2,5-Dibromtoluol3-methylphenethyl bromideBrombenzol3-Brombenzaldehyd1-(Brommethyl)-3-phenoxybenzol3-(4,4,5,5-Tetramethyl-1,3,2-dioxaborolan-2-yl)toluene2-Bromo-4-methylbenzaldehyde3-Methylbiphenyl3-Methylbenzotrifluoride