StartseiteMCPWorkbenchSkills
StartseiteWorkbenchBenachrichtigungenMein Bereich
llms.txt · MCP-AnleitungDatenschutz · Nutzungsbedingungen · Supportv1.8.3
  1. Startseite
  2. /Reaktion

Sodium Hydroxide → (1R,2S)-2-(Methoxycarbonyl)cyclohexane-1-carboxylic acid

HRID 1525515
Drucken

Reaktionsgleichung

Reaktionsgleichung von HRID 1525515
[CH:1]1([C:11]([O:13]C)=[O:12])[CH2:6][CH2:5][CH2:4][CH2:3][CH:2]1[C:7]([O:9][CH3:10])=[O:8].[OH-].[Na+]>P([O-])([O-])([O-])=O.[K+].[K+].[K+]>[CH3:10][O:9][C:7]([C@H:2]1[CH2:3][CH2:4][CH2:5][CH2:6][C@H:1]1[C:11]([OH:13])=[O:12])=[O:8]
KomponentenReaktionsbedingungenVersuchsvorschriftAufarbeitungQuellen und NachweiseNotizen zur Reaktion

Komponenten

4

Edukt 2

HCID 14798Sodium HydroxideHCID 286462Dimethyl cyclohexane-1,2-dicarboxylate

Produkt 1

HCID 11008624(1R,2S)-2-(Methoxycarbonyl)cyclohexane-1-carboxylic acidAusbeute 88,6 %

Reagenzien, Katalysatoren, Lösungsmittel 1

HCID 62657Potassium Phosphate, TribasicLösungsmittel

Reaktionsbedingungen

Temperatur
30 °C

Versuchsvorschrift

Into a 2-L jacketed vessel set at 30° C. was placed dimethyl cyclohexane-1,2-dicarboxylate (2, 84.6 g, 0.42 mol) and 900 mL of 0.1M potassium phosphate buffer, pH 8. The mixture was continuously stirred at 30° C. and PLE (600 mg, 10200 units) was added. The mixture was stirred for 91 hours and the pH was maintained at 8 by addition of 5M NaOH solution. An aliquot from the mixture was analyzed by GC to confirm that residual starting material was less than 5%. The reaction mixture was then filtered through a Celite™ bed and the filtrate was extracted with 250 mL MTBE to remove residual starting material. The aqueous phase was then acidified to pH 4 with concentrated HCl and extracted with 3×500 mL MTBE. The combined extracts were dried over magnesium sulfate and solvent was removed under reduced pressure, to yield 69.28 g (88% yield) of (1R,2S)-2-(methoxycarbonyl)cyclohexane carboxylic acid (4) as a colorless oil with e.e.=79%.

Aufarbeitung

  1. customInto a 2-L jacketed vessel set at 30° C.
  2. additionPLE (600 mg, 10200 units) was added
  3. stirringThe mixture was stirred for 91 hours
  4. filtrationThe reaction mixture was then filtered through a Celite™ bed
  5. extractionthe filtrate was extracted with 250 mL MTBE
  6. customto remove residual
  7. extractionextracted with 3×500 mL MTBE
  8. dry with materialThe combined extracts were dried over magnesium sulfate and solvent
  9. customwas removed under reduced pressure

Quellen und Nachweise

ORD-Eintrag
ord-cf73ef5fa310406b9d64a8cb87da0669
Quelldatensatz
uspto-grants-2015_07
DOI
10.6084/m9.figshare.5104873.v1
Patentnummer
US09080193B2

Notizen zur Reaktion

Auf dieser SeiteKomponentenReaktionsbedingungenVersuchsvorschriftAufarbeitungQuellen und NachweiseNotizen zur Reaktion