HomeMCPWorkbenchSkills
HomeWorkbenchNotificationsMe
llms.txt · MCP GuidePrivacy Policy · Terms of Service · Supportv1.8.3
  1. Home
  2. /Reaction

Ethylene → Ethene propene 1-butene

HRID 423129
Print

Reaction equation

HRID 423129 reaction equation
[CH2:1]=[CH:2][CH2:3][CH3:4].[CH2:5]([Al](CC(C)C)CC(C)C)[CH:6](C)C.C=CC.C=C>CO.[Cl-].[Cl-].C1(C(=[Zr+2](C2C(CC)=CC(C(C)(C)C)=C2)C2C3CC4C(=CC=C(C(C)(C)C)C=4)C=3C=CC=2C(C)(C)C)C2C=CC=CC=2)C=CC=CC=1.C1(C)C=CC=CC=1.CCCCCC>[CH2:1]=[CH:2][CH3:3].[CH2:5]=[CH2:6].[CH2:1]=[CH:2][CH2:3][CH3:4]
ParticipantsConditionsProcedureWorkupSources & evidenceReaction notes

Participants

9

Reactant 4

HCID 6325Ethylene2×HCID 78441-ButeneHCID 8252PropyleneHCID 16682931Triisobutylaluminum

Product 1

HCID 168434Ethene propene 1-butene

Reagents, catalysts & solvents 4

HCID 178436248
HCID 178436248, compound
Catalyst
HCID 887MethanolSolvent2×
HCID 1140TolueneSolvent3×
HCID 8058HexaneSolvent

Conditions

Temperature
55 °C

Procedure

A polymerization reactor of 4000 ml which was sufficiently purged with nitrogen was charged with 1834 ml of dried hexane, 110 g of 1-butene and triisobutylaluminum (1.0 mmol) at ambient temperature. Then, an inside of the polymerization reactor was heated to 55° C., and pressure was applied by propylene so that the inside pressure of the system was 0.58 MPa. Thereafter, the inside pressure of the system was controlled to 0.75 MPa by ethylene. Next, diphenylmethylene(3-tert-butyl-5-ethylcyclopentadienyl)(2,7-di-tert-butylfluorenyl)zirconium dichloride synthesized in Catalyst Synthetic Example 4 was mixed with a toluene solution of methylaluminoxane (manufactured by Tosoh Finechem Corporation) to prepare a toluene solution containing an aluminum atom and a zirconium atom in a proportion of aluminum atom/zirconium atom=300/1 (mole ratio), and then the above toluene solution was taken in an amount containing 0.001 mmol of a zirconium atom (accordingly, an amount containing 0.3 mmol of an aluminum atom) and added to the polymerization reactor. They were polymerized at an inside temperature of 55° C. for 25 minutes while maintaining the inside pressure of the system at 0.75 MPa by ethylene, and 20 ml of methanol was added to terminate the polymerization. After releasing the pressure, the polymer was deposited from the polymerization solution in 4 L of methanol, and the polymer was dried at 130° C. for 12 hours under vacuum. The polymer thus obtained had a weight of 120.2 g and MFR of 0.7 (g/10 minutes). The physical properties obtained by measuring the polymer obtained above are shown in Table 6.

Workup

  1. customA polymerization reactor of 4000 ml which was sufficiently purged with nitrogen
  2. additioncontaining an aluminum atom
  3. additioncontaining 0.001 mmol of a zirconium atom (accordingly, an amount
  4. additioncontaining 0.3 mmol of an aluminum atom) and
  5. additionadded to the polymerization reactor
  6. customThey were polymerized at an inside temperature of 55° C. for 25 minutes
  7. additionwas added
  8. customto terminate
  9. customthe polymerization
  10. customthe polymer was dried at 130° C. for 12 hours under vacuum
  11. customThe polymer thus obtained
  12. customa weight of 120.2 g and MFR of 0.7 (g/10 minutes)
  13. customThe physical properties obtained
  14. customobtained

Sources & evidence

ORD record
ord-bfb34bf2da6b449682583b64d2893d4b
Source dataset
uspto-grants-2012_01
DOI
10.6084/m9.figshare.5104873.v1
Patent number
US08101684B2

Reaction notes

On this pageParticipantsConditionsProcedureWorkupSources & evidenceReaction notes