2-sec-Butylphenol
53466-96-9CCC(C)c1ccccc1ONGFPWHGISWUQOI-UHFFFAOYSA-NO-sec-butylphenol is a clear colorless liquid. (NTP, 1992)
53466-96-9、89-72-5DTXSID2022331CHEMBL30193CHEBI:34303Other Classes -> Phenols
Corrosives
Fragrance Ingredient (Phenol, 2-(1-methylpropyl)-) -> IFRA transparency List
Fragrance
log Kow = 3.27
3.27
3.27
0.981 at 77 °F (NTP, 1992) - Less dense than water; will float
0.9804 kg/l @ 25 °C
Relative density (water = 1): 0.98
0.981
0.89
LIQUID
Amber-colored liquid
Colorless liquid or solid (below 61 degrees F).
less than 1 mg/mL at 68 °F (NTP, 1992)
INSOL IN WATER; SOL IN ALCOHOL, ETHER & ALKALIES
Insoluble in water, slightly soluble in alcohol, ether, and alkalies.
Solubility in water: none
Insoluble
234 °F (NTP, 1992)
234 °F
107 °C
225 °F
225 °F
安全情報は参考情報です。供給元の安全データシート(SDS)、適用法令、専門家による評価に代わるものではありません。
This chemical does not meet GHS hazard criteria for 1.2% (4 of 338) of reports.
Danger
H302 (87.9%): Harmful if swallowed [Warning Acute toxicity, oral]
P260, P261, P264, P264+P265, P270, P271, P273, P280, P301+P317, P301+P330+P331, P302+P352, P302+P361+P354, P304+P340, P305+P354+P338, P316, P317, P321, P330, P362+P364, P363, P391, P405, and P501 (click each P-code to see the statement)
Aggregated GHS information provided per 338 reports by companies from 13 notifications to the ECHA C&L Inventory. Each notification may be associated with multiple companies.
Danger
Chemical: Phenol, 2-(1-methylpropyl)-
Phenol, 2-(1-methylpropyl)- is listed on the EPA's Chemical Data Reporting (CDR) system. Manufacturers and importers of Phenol, 2-(1-methylpropyl)- are required to report information about their production and use of this chemical to the EPA under the Toxic Substances Control Act (TSCA). (40 eCFR Part 711)
REACH registered substance: 2-sec-butylphenol (EC: 201-933-8)
Phenol, 2-(1-methylpropyl)-: Does not have an individual approval but may be used as a component in a product covered by a group standard. It is not approved for use as a chemical in its own right.
The New Jersey Worker and Community Right to Know Act requires public and private employers to provide information about hazardous substances at their workplaces. (N.J.S.A. 34:5A-1 et. seq.)
This chemical is combustible. (NTP, 1992)
Combustible.
Used as a chemical intermediate in the production of resins, plasticizers, and surface active agents; [ACGIH]
CHEMICAL INTERMEDIATE IN PREPN OF RESINS, PLASTICIZERS, SURFACE ACTIVE AGENTS & OTHER PRODUCTS
Derivatives: 2-s-butyl-1-vinylcyclohexyl acetate; dinoseb; fenobucarb.
Chemical intermediate in preparation of resins, plasticizers, surface-active agents.
The main use of 2-(1-methylpropyl)phenol is in the synthesis of insecticides, acaricides, and herbicides.
2-(1-Methylpropyl)phenol is obtained with high selectivity by reaction of phenol with n-butenes at 250-300 °C using gamma- aluminum trioxide as catalyst and at a pressure of 3.5-8.0 Mpa which keeps both reactants in the liquid phase.
Product purity is about 98%.
Plastics Material and Resin Manufacturing
Phenol, 2-(1-methylpropyl)-: ACTIVE
Phenol, 2-methyl(1-methylethyl)-: INACTIVE
用途合成樹脂変性(改質)剤、有機合成原料。
用途ニトロセルロース,アセチルセルロース,天然および、合成樹脂,アルコール可溶染料の溶媒,防湿セロハンの接着,速乾ワニス,エナメル,つめみがきに使用.鉄, 硫酸根,二硫化炭素の定量用試薬, KAR1 FISCHER試薬.
使用Chemical intermediate in preparation of resins, plasticizers, surface-active agents.
439 to 442 °F at 760 mmHg (NTP, 1992)
224-237 °C
224-237 °C
439-442 °F
227 °F
54 °F (NTP, 1992)
14 °C
14 °C
57 °F
61 °F
Relative vapor density (air = 1): 5.2
5.2
Low (NIOSH, 2024)
0.05 [mmHg]
Vapor pressure, Pa at 20 °C: 10
Low
Low
化学的特性colourless to light yellow liquid
Section 8(a) of TSCA requires manufacturers of this chemical substance to report preliminary assessment information concerned with production, use, and exposure to EPA as cited in the preamble in 51 FR 41329.
Pursuant to section 8(d) of TSCA, EPA promulgated a model Health and Safety Data Reporting Rule. The section 8(d) model rule requires manufacturers, importers, and processors of listed chemical substances and mixtures to submit to EPA copies and lists of unpublished health and safety studies. o-sec-Butylphenol is included on this list.
Phenols, such as O-SEC-BUTYLPHENOL, do not behave as organic alcohols, as one might guess from the presence of a hydroxyl (-OH) group in their structure. Instead, they react as weak organic acids. Phenols and cresols are much weaker as acids than common carboxylic acids (phenol has pKa = 9.88). These materials are incompatible with strong reducing substances such as hydrides, nitrides, alkali metals, and sulfides. Flammable gas (H2) is often generated, and the heat of the reaction may ignite the gas. Heat is also generated by the acid-base reaction between phenols and bases. Such heating may initiate polymerization of the organic compound. Phenols are sulfonated very readily (for example, by concentrated sulfuric acid at room temperature). The reactions generate heat. Phenols are also nitrated very rapidly, even by dilute nitric acid.
Fires involving this compound should be controlled with a dry chemical, carbon dioxide or halon extinguisher. (NTP, 1992)
Use carbon dioxide, foam, powder.
Fresh air, rest. Refer for medical attention.
Remove contaminated clothes. Rinse and then wash skin with water and soap. Refer for medical attention .
First rinse with plenty of water for several minutes (remove contact lenses if easily possible), then refer for medical attention.
Rinse mouth. Do NOT induce vomiting. Refer for medical attention .
EYES: First check the victim for contact lenses and remove if present. Flush victim's eyes with water or normal saline solution for 20 to 30 minutes while simultaneously calling a hospital or poison control center. Do not put any ointments, oils, or medication in the victim's eyes without specific instructions from a physician. IMMEDIATELY transport the victim after flushing eyes to a hospital even if no symptoms (such as redness or irritation) develop.
(General first aid procedures)
SMALL SPILLS AND LEAKAGE: If you spill this chemical, FIRST REMOVE ALL SOURCES OF IGNITION. Then, use absorbent paper to pick up all liquid spill material. Your contaminated clothing and absorbent paper should be sealed in a vapor-tight plastic bag for eventual disposal. Solvent wash all contaminated surfaces with 60-70% ethanol followed by washing with a soap and water solution. Do not reenter the contaminated area until the Safety Officer (or other responsible person) has verified that the area has been properly cleaned.
SRP: At the time of review, criteria for land treatment or burial (sanitary landfill) disposal practices are subject to significant revision. Prior to implementing land disposal of waste residue (including waste sludge), consult with environmental regulatory agencies for guidance on acceptable disposal practices.
Collect leaking and spilled liquid in sealable containers as far as possible. Sweep spilled substance into covered containers. Carefully collect remainder. Then store and dispose of according to local regulations. Personal protection: chemical protection suit.
The worker should immediately wash the skin when it becomes contaminated.
Work clothing that becomes wet or significantly contaminated should be removed and replaced.
TERRESTRIAL FATE: Based on a recommended classification scheme(1), an estimated Koc value of 1400(SRC), determined from an experimental log Kow(2) and a recommended regression-derived equation(3), indicates that 2-(1-methylpropyl)phenol will have low mobility in soil(SRC). Volatilization of 2-(1-methylpropyl)phenol from moist soil surfaces will be slow(SRC) given an estimated Henry's Law constant of 2.1X10-6 atm-cu m/mole(4,SRC). Limited data, mainly derived by analogy to 4-s-butylphenol, indicate that 2-(1-methylpropyl)phenol may be resistant to biodegradation by non-adapted microbial populations(SRC). Resting cells of a Pseudomonas strain obtained by selective enrichment with 4-hydroxybenzoate as the sole carbon source, were able to biodegrade 2-(1-methylpropyl)phenol (oxygen uptake rate of 42 nmol O2/min/mg protein)(5). A structurally similar compound, 4-s-butylphenol (at 100 mg/L) was not biodegraded over a 2 week period using an activated sludge inoculum(6); however, a phenol-adapted yeast strain, isolated from soil, readily oxidized 4-s-butylphenol (present at 1 mmole) without a lag period(7).
AQUATIC FATE: Based on a recommended classification scheme(1), an estimated Koc value of 1400(SRC), determined from an experimental log Kow(2) and a recommended regression-derived equation(3), indicates that 2-(1-methylpropyl)phenol would adsorb to suspended solids and sediment(SRC) in the water. 2-(1-Methylpropyl)phenol may volatilize from water surfaces based on an estimated Henry's Law constant of 2.1X10-6 atm-cu m/mole(SRC), developed using a fragment constant estimation method(4). Estimated half-lives for a model river and model lake are 21 and 160 days, respectively(3,SRC). Limited data, mainly derived by analogy to 4-s-butylphenol, indicate that 2-(1-methylpropyl)phenol may be resistant to biodegradation by non-adapted microbial populations(SRC). A 4-hydroxybenzoate adapted Pseudomonas strain was able to biodegrade 2-(1-methylpropyl)phenol (oxygen uptake rate of 42 nmol O2/min/mg protein)(5). A structurally similar compound, 4-s-butylphenol (at 100 mg/L) was not biodegraded over a 2 week period using an activated sludge inoculum(6); however, a phenol-adapted yeast strain, isolated from soil, readily oxidized 4-s-butylphenol (present at 1 mmole) without a lag period(7). An estimated BCF value of 180(3,SRC), determined from an experimental log Kow(2), suggests that 2-(1-methylpropyl)phenol may bioconcentrate in aquatic organisms(SRC) according to a recommended classification scheme(8).
ATMOSPHERIC FATE: According to a suggested classification scheme(1), an estimated vapor pressure of 0.05 mm Hg at 25 °C(2,SRC) indicates that 2-(1-methylpropyl)phenol will exist mainly in the vapor phase in the ambient atmosphere. Vapor-phase 2-(1-methylpropyl)phenol is degraded in the atmosphere by reaction with photochemically produced hydroxyl radicals(SRC); the half-life for this reaction in air is estimated to be about 9 hours(3,SRC).
The substance can be absorbed into the body by inhalation of its vapour, through the skin and by ingestion.
inhalation, skin absorption, ingestion, skin and/or eye contact
Cough. Sore throat.
Pain. Blisters. Skin burns.
Redness. Pain. Blurred vision. Severe deep burns.
Burning sensation in the throat and chest. Abdominal pain. Shock or collapse. Vomiting.
irritation eyes, skin, respiratory system; skin burns
The Koc of 2-(1-methylpropyl)phenol is estimated as approximately 1400(SRC), using an experimental log Kow of 3.27(1) and a regression-derived equation(2,SRC). According to a recommended classification scheme(3), this estimated Koc value suggests that 2-(1-methylpropyl)phenol has low mobility in soil(SRC).
2-(1-Methylpropyl)phenol's production and use as a chemical intermediate in the preparation of resins, plasticizers, surface-active agents(1) or as an intermediate in the synthesis of insecticides, acaricides, and herbicides(2) may result in its release to the environment through various waste streams(SRC).
Resting cells of a Pseudomonas strain, obtained by selective enrichment with 4-hydroxybenzoate as the sole carbon source, were able to biodegrade 2-(1-methylpropyl)phenol (oxygen uptake rate of 42 nmol O2/min/mg protein)(1). A structurally similar compound, 4-s-butylphenol (at 100 mg/L), was not biodegraded over a 2 week period using an activated sludge inoculum(2); however, a phenol-adapted yeast strain, isolated from soil, readily oxidized 4-s-butylphenol (present at 1 mmole) without a lag period(3).
An estimated BCF value of 180 was calculated for 2-(1-methylpropyl)phenol(SRC), using an experimental log Kow of 3.27(1) and a recommended regression-derived equation(2). According to a recommended classification scheme(3), this BCF value suggests that bioconcentration in aquatic organisms may occur(SRC).
The Henry's Law constant for 2-(1-methylpropyl)phenol is estimated as 2.1X10-6 atm-cu m/mole(SRC) using a fragment constant estimation method(1). This value indicates that 2-(1-methylpropyl)phenol will volatilize from water surfaces(2,SRC). Based on this Henry's Law constant, the volatilization half-life from a model river (1 m deep, flowing 1 m/sec, wind velocity of 3 m/sec) is estimated as approximately 21 days(2,SRC). The volatilization half-life from a model lake (1 m deep, flowing 0.05 m/sec, wind velocity of 0.5 m/sec) is estimated as approximately 160 days(2,SRC). 2-(1-Methylpropyl)phenol's estimated vapor pressure, 0.05 mm Hg(3,SRC) and Henry's Law constant(1,SRC) indicate that volatilization from dry and moist soil will be slow(SRC).
Section 8(a) of TSCA requires manufacturers of this chemical substance to report preliminary assessment information concerned with production, use, and exposure to EPA as cited in the preamble in 51 FR 41329.
Pursuant to section 8(d) of TSCA, EPA promulgated a model Health and Safety Data Reporting Rule. The section 8(d) model rule requires manufacturers, importers, and processors of listed chemical substances and mixtures to submit to EPA copies and lists of unpublished health and safety studies. o-sec-Butylphenol is included on this list.
一般的な説明Clear colorless liquid.
定義ChEBI: A member of the class of phenols that is phenol carrying a butan-2-yl group at position 2.