브롬화 수은

White crystals or crystalline powder

Colorless rhombic crystals

White, rhombic crystals

Sol in about 200 parts cold, 25 parts boiling water; freely sol in hot alcohol, in methanol, hydrogen bromide, alkali bromide soln, hydrochloric acid; slightly sol in chloroform.

VERY SLIGHTLY SOL IN ETHER

Mercuric bromide appears as white rhombic crystals. Sensitive to light. Slightly soluble in water and denser than water. Severely toxic by inhalation and ingestion.

Light-sensitive, white solid; [Merck Index]

Sublimes at temp higher than 237 °C

Light sensitive

Danger

H300 (100%): Fatal if swallowed [Danger Acute toxicity, oral]；H310 (100%): Fatal in contact with skin [Danger Acute toxicity, dermal]；H330 (100%): Fatal if inhaled [Danger Acute toxicity, inhalation]；H373 (100%): May causes damage to organs through prolonged or repeated exposure [Warning Specific target organ toxicity, repeated exposure]；H400 (94.1%): Very toxic to aquatic life [Warning Hazardous to the aquatic environment, acute hazard]；H410 (100%): Very toxic to aquatic life with long lasting effects [Warning Hazardous to the aquatic environment, long-term hazard]

P260, P262, P264, P270, P271, P273, P280, P284, P301+P316, P302+P352, P304+P340, P316, P319, P320, P321, P330, P361+P364, P391, P403+P233, P405, and P501 (click each P-code to see the statement)

Aggregated GHS information provided per 51 reports by companies from 7 notifications to the ECHA C&L Inventory. Each notification may be associated with multiple companies.；Information may vary between notifications depending on impurities, additives, and other factors. The percentage value in parenthesis indicates the notified classification ratio from companies that provide hazard codes. Only hazard codes with percentage values above 10% are shown. For more detailed information, please visit ECHA C&L website.

Chemical: Mercury bromide (HgBr2)

Mercury (II) bromide: HSNO Approval: HSR004544 Approved with controls

Excerpt from ERG Guide 154 [Substances - Toxic and/or Corrosive (Non-Combustible)]:；Non-combustible, substance itself does not burn but may decompose upon heating to produce corrosive and/or toxic fumes. Some are oxidizers and may ignite combustibles (wood, paper, oil, clothing, etc.). Corrosives in contact with metals may evolve flammable hydrogen gas. Containers may explode when heated. For electric vehicles or equipment, ERG Guide 147 (lithium ion or sodium ion batteries) or ERG Guide 138 (sodium batteries) should also be consulted. (ERG, 2024)

Excerpt from ERG Guide 154 [Substances - Toxic and/or Corrosive (Non-Combustible)]:；TOXIC and/or CORROSIVE; inhalation, ingestion or skin contact with material may cause severe injury or death. Contact with molten substance may cause severe burns to skin and eyes. Avoid any skin contact. Fire may produce irritating, corrosive and/or toxic gases. Runoff from fire control or dilution water may be corrosive and/or toxic and cause environmental contamination. (ERG, 2024)

D009; A solid waste containing mercury may or may not become characterized as a hazardous waste when subjected to the Toxicity Characteristic Leaching Procedure listed in 40 CFR 261.24, and if so characterized, must be managed as a hazardous waste. /Mercury/

Reacts with sodium azide to give mercury(II) azide, which is sensitive to shock, friction, and heat. Mixing with hydrazine salts in basic solution produced a heat or shock sensitive yellow precipitate [Annalen, 1899, 305, 191]. Reacts violently with chlorine trifluoride *with ignition often occurring.

Listed as a hazardous air pollutant (HAP) generally known or suspected to cause serious health problems. The Clean Air Act, as amended in 1990, directs EPA to set standards requiring major sources to sharply reduce routine emissions of toxic pollutants. EPA is required to establish and phase in specific performance based standards for all air emission sources that emit one or more of the listed pollutants. Mercuric bromide is included on this list.

/GUIDE 154: SUBSTANCES - TOXIC AND/OR CORROSIVE (NON-COMBUSTIBLE)/ Health: TOXIC; inhalation, ingestion, or skin contact with material may cause severe injury or death. Contact with molten substance may cause severe burns to skin and eyes. Avoid any skin contact. Effects of contact or inhalation may be delayed. Fire may produce irritating, corrosive and/or toxic gases. Runoff from fire control or dilution water may be corrosive and/or toxic and cause pollution.

/GUIDE 154: SUBSTANCES - TOXIC AND/OR CORROSIVE (NON-COMBUSTIBLE)/ Fire or Explosion: Non-combustible, substance itself does not burn but may decompose upon heating to produce corrosive and/or toxic fumes. Some are oxidizers and may ignite combustibles (wood, paper, oil, clothing, etc.). Contact with metals may evolve flammable hydrogen gas. Containers may explode when heated.

/GUIDE 154: SUBSTANCES - TOXIC AND/OR CORROSIVE (NON-COMBUSTIBLE)/ Public Safety: CALL Emergency Response Telephone Number ... . As an immediate precautionary measure, isolate spill or leak area in all directions for at least 50 meters (150 feet) for liquids and at least 25 meters (75 feet) for solids. Keep unauthorized personnel away. Stay upwind. Keep out of low areas. Ventilate enclosed areas.

/GUIDE 154: SUBSTANCES - TOXIC AND/OR CORROSIVE (NON-COMBUSTIBLE)/ Protective Clothing: Wear positive pressure self-contained breathing apparatus (SCBA). Wear chemical protective clothing that is specifically recommended by the manufacturer. It may provide little or no thermal protection. Structural firefighters' protective clothing provides limited protection in fire situations ONLY; it is not effective in spill situations where direct contact with the substance is possible.

For more DOT Emergency Guidelines (Complete) data for MERCURIC BROMIDE (8 total), please visit the HSDB record page.

Excerpt from ERG Guide 154 [Substances - Toxic and/or Corrosive (Non-Combustible)]:；SMALL FIRE: Dry chemical, CO2 or water spray.；LARGE FIRE: Dry chemical, CO2, alcohol-resistant foam or water spray. If it can be done safely, move undamaged containers away from the area around the fire. Dike runoff from fire control for later disposal.；FIRE INVOLVING TANKS, RAIL TANK CARS OR HIGHWAY TANKS: Fight fire from maximum distance or use unmanned master stream devices or monitor nozzles. Do not get water inside containers. Cool containers with flooding quantities of water until well after fire is out. Withdraw immediately in case of rising sound from venting safety devices or discoloration of tank. ALWAYS stay away from tanks in direct contact with flames. (ERG, 2024)

Excerpt from ERG Guide 154 [Substances - Toxic and/or Corrosive (Non-Combustible)]:；Refer to the "General First Aid" section. Specific First Aid: For corrosives, in case of contact, immediately flush skin or eyes with running water for at least 30 minutes. Additional flushing may be required. (ERG, 2024)

1) Ventilate area of spill. 2) Collect spilled material for reclamation using commercially available mercury vapor depressants or specialized vacuum cleaners.

Mercury spills should be cleaned up immediately by use of a special vacuum cleaner. Then the area should be washed with a dilute calcium sulfide solution. Small quantities of mercury can be picked up by mixing with copper metal granules. ... /Mercury/

Mercury removal from waste water can be accomplished by these processes: BMS process; Chlorine is added to the waste water, oxidizing any mercury present to the ionic state. The BMS adsorbent (an activated carbon concentrate of sulfur cmpd on its surface) is used to collect ionic mercury. The spent adsorbent is then distilled to recover the mercury, leaving a carbon residue for reuse or disposal. TMR IMAC Process; Waste water is fed into a reactor, whereby a slight excess of chlorine is maintained, oxidizing any mercury present to ionic mercury. The liquid is then passed through the TMR IMAC ion-exchange resin where mercury ions are adsorbed. The mercury is then stripped from the spent resin with hydrochloric acid solution. /Mercury cmpds/

SPILLED MERCURY CMPD OR SOLN CAN BE CLEANED UP BY ANY METHOD THAT DOES NOT CAUSE EXCESSIVE AIRBORNE CONTAMINATION OR SKIN CONTACT. /MERCURY COMPOUNDS/

1) Ventilate area of spill. 2) Collect spilled material for reclamation using commercially available mercury vapor depressants or specialized vacuum cleaners. /Inorganic mercury/

Excerpt from ERG Guide 154 [Substances - Toxic and/or Corrosive (Non-Combustible)]:；ELIMINATE all ignition sources (no smoking, flares, sparks or flames) from immediate area. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Stop leak if you can do it without risk. Prevent entry into waterways, sewers, basements or confined areas. Absorb or cover with dry earth, sand or other non-combustible material and transfer to containers. DO NOT GET WATER INSIDE CONTAINERS. (ERG, 2024)

SRP: At the time of review, criteria for land treatment or burial (sanitary landfill) disposal practices are subject to significant revision. Prior to implementing land disposal of waste residue (including waste sludge), consult with environmental regulatory agencies for guidance on acceptable disposal practices.

SRP: The scientific literature for the use of contact lenses in industry is conflicting. The benefit or detrimental effects of wearing contact lenses depend not only upon the substance, but also on factors including the form of the substance, characteristics and duration of the exposure, the uses of other eye protection equipment, and the hygiene of the lenses. However, there may be individual substances whose irritating or corrosive properties are such that the wearing of contact lenses would be harmful to the eye. In those specific cases, contact lenses should not be worn. In any event, the usual eye protection equipment should be worn even when contact lenses are in place.

If material not involved in fire: Keep material out of water sources and sewers.

Personnel protection: Avoid breathing dusts, and fumes from burning material. Keep upwind. Avoid bodily contact with the material. ... Do not handle broken packages unless wearing appropriate personal protective equipment. Wash away any material which may have contacted the body with copious amounts of water or soap and water. ... If contact with the material anticipated, wear appropriate chemical protective clothing.

Preventative measure: adequate ventilation; careful attention to good housekeeping, e.g., avoidance of spills, and prompt and proper cleaning if a spill occurs; all containers of mercury and its compounds should be kept tightly closed; should be washed on a regular basis with dilute calcium sulfide solution or other suitable reactant; floors should be nonporous; all workers directly involved in the plant operation should shower thoroughly each day before leaving. /Mercury compounds/

Excerpt from ERG Guide 154 [Substances - Toxic and/or Corrosive (Non-Combustible)]:；IMMEDIATE PRECAUTIONARY MEASURE: Isolate spill or leak area in all directions for at least 50 meters (150 feet) for liquids and at least 25 meters (75 feet) for solids.；SPILL: Increase the immediate precautionary measure distance, in the downwind direction, as necessary.；FIRE: If tank, rail tank car or highway tank is involved in a fire, ISOLATE for 800 meters (1/2 mile) in all directions; also, consider initial evacuation for 800 meters (1/2 mile) in all directions. (ERG, 2024)

0.02 [mg/m3], as Hg

8 hr Time Weighted Avg (TWA): 0.025 mg/cu m, skin /Mercury, elemental and inorganic forms, Hg/

Excursion Limit Recommendation: Excursions in worker exposure levels may exceed 3 times the TLV-TWA for no more than a total of 30 minutes during a work day, and under no circumstances should they exceed 5 times the TLV-TWA, provided that the TLV-TWA is not exceeded. /Mercury, elemental and inorganic forms, as Hg/

A4: Not classifiable as a human carcinogen. /Mercury, elemental and inorganic forms, as Hg/

Biological Exposure Index (BEI): Determinant: total inorganic mercury in urine; Sampling Time: Prior to shift; BEI: 35 ug/g creatinine. The determinant may be present in biological specimens collected from subjects who have not been occupationally exposed, at a concentration which could affect interpretation of the result. Such background concentrations are incorporated in the BEI value. /Mercury/

Biological Exposure Index (BEI): Determinant: total inorganic mercury in blood; Sampling Time: end of shift at end of workweek; BEI: 15 ug/L. The determinant may be present in biological specimens collected from subjects who have not been occupationally exposed, at a concentration which could affect interpretation of the result. Such background concentrations are incorporated in the BEI value. /Mercury/

EYES: irrigate opened eyes for several minutes under running water. INGESTION: do not induce vomiting. Rinse mouth with water (never give anything by mouth to an unconscious person). Seek immediate medical advice. SKIN: should be treated immediately by rinsing the affected parts in cold running water for at least 15 minutes, followed by thorough washing with soap and water. If necessary, the person should shower and change contaminated clothing and shoes, and then must seek medical attention. INHALATION: supply fresh air. If required provide artificial respiration.

Mercury mainly affects the nervous system. Exposure to high levels of metallic, inorganic, or organic mercury can permanently damage the brain, kidneys, and developing fetus. Effects on brain functioning may result in irritability, shyness, tremors, changes in vision or hearing, and memory problems. Acrodynia, a type of mercury poisoning in children, is characterized by pain and pink discoloration of the hands and feet. Mercury poisoning can also cause Hunter-Russell syndrome and Minamata disease. Bromine vapour causes irritation and direct damage to the mucous membranes. Elemental bromine also burns the skin. The bromide ion is a central nervous system depressant and chronic exposure produces neuronal effects. This is called bromism and can result in central reactions reaching from somnolence to coma, cachexia, exicosis, loss of reflexes or pathologic reflexes, clonic seizures, tremor, ataxia, loss of neural sensitivity, paresis, papillar edema of the eyes, abnormal speech, cerebral edema, delirium, aggressiveness, and psychoses. (L625, L626, L627, L7)

High-affinity binding of the divalent mercuric ion to thiol or sulfhydryl groups of proteins is believed to be the major mechanism for the activity of mercury. Through alterations in intracellular thiol status, mercury can promote oxidative stress, lipid peroxidation, mitochondrial dysfunction, and changes in heme metabolism. Mercury is known to bind to microsomal and mitochondrial enzymes, resulting in cell injury and death. For example, mercury is known to inhibit aquaporins, halting water flow across the cell membrane. It also inhibits the protein LCK, which causes decreased T-cell signalling and immune system depression. Mercury is also believed to inhibit neuronal excitability by acting on the postsynaptic neuronal membrane. It also affects the nervous system by inhibiting protein kinase C and alkaline phosphatase, which impairs brain microvascular formation and function, as well as alters the blood-brain barrier. Mercury also produces an autoimmune response, likely by modification of major histocompatibility complex (MHC) class II molecules, self peptides, T-cell receptors, or cell-surface adhesion molecules. Bromine is a powerful oxidizing agent and is able to release oxygen free radicals from the water in mucous membranes. These free radicals are also potent oxidizers and produce tissue damage. In additon, the formation of hydrobromic and bromic acids will result in secondary irritation. The bromide ion is also known to affect the central nervous system, causing bromism. This is believed to be a result of bromide ions substituting for chloride ions in the in actions of neurotransmitters and transport systems, thus affecting numerous synaptic processes. (L626, L627, A543, L7, A8, A25, A26)

In the atmosphere, particulate bound mercury constitutes only approximately 2% of total mercury in the air and has normally been found to be less than 0.1 ng/cu m in regions unaffected by local sources(1). Some other mercury compounds which may exist in the atmosphere are mercuric chloride, mercuric bromide, mercuric hydroxide, mercuric sulfide, and mercuric cyanide(1). The rest is elemental mercury in the gaseous phase. In remote areas over the Atlantic and Pacific oceans, mercury bound to particulate matter concns are generally at or below the picogram per cubic meter level(1).

Toxic by ingestion, inhalation, and skin absorption.

Contact with eyes causes ulceration of conjunctiva & cornea.

CLASSIFICATION: D; not classifiable as to human carcinogenicity. BASIS FOR CLASSIFICATION: No human data are available. Animal and supporting data are inadequate. HUMAN CARCINOGENICITY DATA: None. /Mercury (inorganic)/

A4: Not classifiable as a human carcinogen. /Mercury, elemental and inorganic forms, as Hg/

Chemical: Mercury bromide (HgBr2)

Mercury (II) bromide: HSNO Approval: HSR004544 Approved with controls

D009; A solid waste containing mercury may or may not become characterized as a hazardous waste when subjected to the Toxicity Characteristic Leaching Procedure listed in 40 CFR 261.24, and if so characterized, must be managed as a hazardous waste. /Mercury/

Listed as a hazardous air pollutant (HAP) generally known or suspected to cause serious health problems. The Clean Air Act, as amended in 1990, directs EPA to set standards requiring major sources to sharply reduce routine emissions of toxic pollutants. EPA is required to establish and phase in specific performance based standards for all air emission sources that emit one or more of the listed pollutants. Mercuric bromide is included on this list.

Mercury is absorbed mainly via ingestion and inhalation, then distributed throughout the body via the bloodstream, where a portion binds to sulfhydryl groups on haemoglobin. Mercury can undergo oxidation to mercuric mercury, which takes place via the catalase-hydrogen peroxide pathway. The mercury atom is able to diffuse down the cleft in the catalase enzyme to reach the active site where the heme ring is located. Oxidation most likely occurs in all tissue, as the catalase hydrogen peroxide pathway is ubiquitous. Following oxidation, mercury tends to accumulate in the kidneys. Mercury is excreted mainly by exhalation and in the faeces. Bromine is mainly absorbed via inhalation, but may also enter the body through dermal contact. Bromine salts can be ingested. Due to its reactivity, bromine quickly forms bromide and may be deposited in the tissues, displacing other halogens. (L626, A6, L7)

The transport and binding of inorganic mercury compounds in rat intestinal tissues were studied in vitro. Everted intestinal sacs and intestinal brush border membrane vesicles from male Wistar rats were incubated for 30 and 10 minutes, respectively, with 1X 10(-4) molar mercuric acetate, mercuric chloride, mercuric thiocyanate, mercuric bromide, or mercuric cyanide at pHs of 5.5, 6.4, or 7.4. The tissues were analyzed for mercury. The amount of each compound transported through the sac and brush border membrane vesicle walls and the amount bound to the tissues were calculated. The data were compared with the stability constants of the compounds. In the intestinal sacs increases in pH tended to increase the transport of each compound through the wall and tended to decrease the amount bound. Mercuric acetate was transported through the intestinal wall to the greatest extent, followed by mercuric chloride, mercuric thiocyanate, mercuric bromide, and mercuric cyanide, in that order. The degree of transport of the compounds correlated inversely with the logarithm of their stability constants. In brush border membrane vesicles, uptake of the compounds also correlated inversely with the logarithm of their stability constants. Increases in pH significantly increased uptake of all compounds except mercuric cyanide. Mercuric acetate, mercuric chloride, mercuric thiocyanate, mercuric bromide, and mercuric-cyanide were incubated with rat brush border membrane vesicles at pH 5.5, 6.4, or 7.4 in hypertonic medium to assess the effects of osmolarity on uptake. Uptake of mercuric acetate and mercuric chloride at each pH decreased linearly with increasing osmolarity. Uptake of mercuric thiocyanate and mercuric bromide at each pH tended to decrease with increasing osmolarity. Uptake of mercuric cyanide was not affected by changes in osmolarity.

Used in medicines, reagents, intermediates, and catalysts; [HSDB]

/In prepn of/ medicines

... Convert inorg mercury to methylmercury. /Mercuric salts/

Used as a reagent for arsenic and antimony, as an intermediate in the production of bromine-containing organomercury compounds, and as a catalyst in organic synthesis. The melt is used as a nonaqueous solvent.

Mercury(II) bromide is used mainly as a laboratory reagent. (L440)

By adding potassium bromide to a solution of mercuric salt and crystallizing.

Prepared by precipitation, using mercuric nitrate and sodium bromide solution.

By dissolution of mercury(II) oxide in hydrobromic acid.