Huagongshe화공사 화학 정보 인쇄 보고서 · 연구 참고용
아니졸
아니솔 · 아니졸 · METHOXYBENZENE · ANISOL · MOB · FEMA 2097 · METHYL PHENYL ETHER · Phenoxymethane
식별자 및 물리적 특성
| CAS No. | 100-66-3 |
|---|---|
| 분자식 | C7H8O |
| 평균 분자량 | 108.14 g/mol |
| 단동위원소 질량 | 108.05751487 g/mol |
| SMILES | COc1ccccc1 |
| InChIKey | RDOXTESZEPMUJZ-UHFFFAOYSA-N |
| PubChem CID | 7519 |
| ChEMBL | CHEMBL278024 |
| ChEBI | CHEBI:16579 |
| EC No. | 202-876-1 |
| DTXSID | DTXSID4041608 |
| 현지명 | 아니졸 |
화학 및 물리적 성질
| XLogP | 2.1 |
|---|---|
| 극성 표면적 | 9.2 |
| 수소 결합 공여자 수 | 0 |
| 수소 결합 수용자 수 | 1 |
| 회전 가능 결합 수 | 1 |
| 무거운 원자 수 | 8 |
| 형식 전하 | 0 |
| 복잡도 | 55 |
| LogP(분배 계수) | Log Kow = 2.11 |
| 냄새 | SWEET ANISE-LIKE ODORAgreeable aromatic odorSpicy-sweet페놀, 아니스 냄새 |
| 맛 | SWEET |
| 밀도 | 0.9956 AT 18 °C/4 °CPER CENT IN SATURATED AIR: 0.41DENSITY OF SATURATED AIR: 1.1 (AIR= 1)Relative density (water = 1): 0.990.990-0.9931.515 @25 °C0.995 g/mL at 25 °C (lit.) |
| Viscosity | 1.52 centipoise at 15 °C0.778 centipoise at 30 °C |
| Color/Form | MOBILE LIQUID, CLEAR STRAW COLORColorless liquid |
| 용해도 | SOLUBLE IN ALCOHOL AND ETHERVERY SOLUBLE IN ACETONEWater solubility = 1520 mg/LWater solubility = 10,400 mg/LWater solubility = 143 mg/L1.04 mg/mL at 25 °C1.71g/L |
| 인화점 | 125 °F (NFPA, 2010)52 °C125 °F (52 °C) (OPEN CUP)52 °C o.c. |
| 끓는 점 | 155.5 °C AT 760 MM HG153.00 to 155.00 °C. @ 760.00 mm Hg155 °C154 °C153.8 °C @760 [mm Hg]154 °C (lit.) |
| Decomposition | When heated to decomp, emits acrid fumes. |
| 녹는점 | -37.3 °C-37.5 °C-37 °C-37 °C (lit.) |
| 증기 밀도 | 3.72 (AIR= 1)Relative vapor density (air = 1): 3.73.7 (vs air) |
| 증기압 | 10 mm Hg ( 42.2 °C) |
| 굴절률 | n20/D 1.516(lit.) |
| FEMA | 2097 | ANISOLE |
| 저장 조건 | Store below +30°C. |
| 물리적 상태 | 액체 |
| 색상 | 무색의 |
| 향취 유형 | 페놀성 |
| 후각 역치 | 0.057ppm |
| 생물학적 소스 | synthetic |
| 폭발한계 | 0.34-6.3%(V) |
| 용해도 | 1.6g/L(20℃) |
| JECFA Number | 1241 |
| Merck | 14,669 |
| BRN | 506892 |
| 헨리 상수 | 2.9×10-2 mol/(m3Pa) at 25℃, Brockbank (2013) |
| 유전율 | 4.3(20℃) |
| 안정성 | 안정적인. 가연성. 강한 산화제와 호환되지 않습니다. |
| 화장품 원료 기능 | 향수 |
| InChI | 1S/C7H8O/c1-8-7-5-3-2-4-6-7/h2-6H,1H3 |
| InChIKey | RDOXTESZEPMUJZ-UHFFFAOYSA-N |
| SMILES | COc1ccccc1 |
| LogP(분배 계수) | 2.62 at 30℃ |
| NIST | Benzene, methoxy-(100-66-3) |
| EPA | Anisole (100-66-3) |
화학적 성질
Anisole is a colorless to yellowish liquid with a characteristic pleasant, anise-like, agreeable, aromatic, spicy-sweet odor. It is used in perfumery.
안전 및 규제
| GHS 분류 | This chemical does not meet GHS hazard criteria for < 0.1% (1 of 2013) of reports.WarningH226 (> 99.9%): Flammable liquid and vapor [Warning Flammable liquids]H315 (76.5%): Causes skin irritation [Warning Skin corrosion/irritation]H319 (78.1%): Causes serious eye irritation [Warning Serious eye damage/eye irritation]H336 (13.1%): May cause drowsiness or dizziness [Warning Specific target organ toxicity, single exposureNarcotic effects]P210, P233, P240, P241, P242, P243, P261, P264, P264+P265, P271, P280, P302+P352, P303+P361+P353, P304+P340, P305+P351+P338, P319, P321, P332+P317, P337+P317, P362+P364, P370+P378, P403+P233, P403+P235, P405, and P501 (click each P-code to see the statement)Aggregated GHS information provided per 2013 reports by companies from 29 notifications to the ECHA C&L Inventory. Each notification may be associated with multiple companies.Reported as not meeting GHS hazard criteria per 1 of 2013 reports by companies.There are 28 notifications provided by 2012 of 2013 reports by companies with hazard statement code(s).Information may vary between notifications depending on impurities, additives, and other factors. The percentage value in parenthesis indicates the notified classification ratio from companies that provide hazard codes. Only hazard codes with percentage values above 10% are shown. For more detailed information, please visit ECHA C&L website. |
|---|---|
| 규제 정보 | Chemical: Benzene, methoxy-Commission Regulation (EC) No 1565/2000 (Repealed by Com. Implementing Reg. (EU) No 872/2012)Benzene, methoxy- is listed on the EPA's Chemical Data Reporting (CDR) system. Manufacturers and importers of Benzene, methoxy- are required to report information about their production and use of this chemical to the EPA under the Toxic Substances Control Act (TSCA). (40 eCFR Part 711)Status: Active Update: 06-10-2022 https://echa.europa.eu/registration-dossier/-/registered-dossier/14423Status: Active Update: 16-09-2015 https://echa.europa.eu/registration-dossier/-/registered-dossier/16204Status: Active Update: 21-11-2012 https://echa.europa.eu/registration-dossier/-/registered-dossier/6974Status: Active Update: 03-07-2020 https://echa.europa.eu/registration-dossier/-/registered-dossier/31271Benzene, methoxy-: HSNO Approval: HSR001037 Approved with controlsThe New Jersey Worker and Community Right to Know Act requires public and private employers to provide information about hazardous substances at their workplaces. (N.J.S.A. 34:5A-1 et. seq.) |
| 운송 라벨(DOT) | Flammable Liquid |
| 화재 위험 | Excerpt from ERG Guide 128 [Flammable Liquids (Water-Immiscible)]:HIGHLY FLAMMABLE: Will be easily ignited by heat, sparks or flames. Vapors may form explosive mixtures with air. Vapors may travel to source of ignition and flash back. Most vapors are heavier than air. They will spread along the ground and collect in low or confined areas (sewers, basements, tanks, etc.). Vapor explosion hazard indoors, outdoors or in sewers. Those substances designated with a (P) may polymerize explosively when heated or involved in a fire. Runoff to sewer may create fire or explosion hazard. Containers may explode when heated. Many liquids will float on water. Substance may be transported hot. For hybrid vehicles, ERG Guide 147 (lithium ion or sodium ion batteries) or ERG Guide 138 (sodium batteries) should also be consulted. If molten aluminum is involved, refer to ERG Guide 169. (ERG, 2024)· HIGHLY FLAMMABLE: Will be easily ignited by heat, sparks or flames.· Vapors may form explosive mixtures with air.· Vapors may travel to source of ignition and flash back.· Most vapors are heavier than air. They will spread along the ground and collect in low or confined areas (sewers, basements, tanks, etc.).· Vapor explosion hazard indoors, outdoors or in sewers.· Those substances designated with a (P) may polymerize explosively when heated or involved in a fire.· Runoff to sewer may create fire or explosion hazard.· Containers may explode when heated.· Many liquids will float on water.· Substance may be transported hot.· For hybrid vehicles, GUIDE 147 (lithium ion or sodium ion batteries) or GUIDE 138 (sodium batteries) should also be consulted.· If molten aluminum is involved, refer to GUIDE 169.Flammable. Above 52 °C explosive vapour/air mixtures may be formed. |
| 건강 유해성 | Excerpt from ERG Guide 128 [Flammable Liquids (Water-Immiscible)]:CAUTION: Petroleum crude oil (UN1267) may contain TOXIC hydrogen sulphide gas. Inhalation or contact with material may irritate or burn skin and eyes. Fire may produce irritating, corrosive and/or toxic gases. Vapors may cause dizziness or asphyxiation, especially when in closed or confined areas. Runoff from fire control or dilution water may cause environmental contamination. (ERG, 2024)CAUTION: Petroleum crude oil (UN1267) may contain TOXIC hydrogen sulphide gas.· Inhalation or contact with material may irritate or burn skin and eyes.· Fire may produce irritating, corrosive and/or toxic gases.· Vapors may cause dizziness or asphyxiation, especially when in closed or confined areas.· Runoff from fire control or dilution water may cause environmental contamination. |
| 유해성 요약 | Causes CNS depression in high-dose animal studies[HSDB] A skin, eye, and respiratory tract irritant[ICSC] May cause irritation[MSDSonline] |
| 운송 번호 및 가이드(DOT) | 2222 128 |
| FDA 요건 | Anisole is a food additive permitted for direct addition to food for human consumption as a synthetic flavoring substance and adjuvant in accordance with the following conditions: 1) the quantity added to food does not exceed the amount reasonably required to accomplish its intended physical, nutritive, or other technical effect in food, and 2) when intended for use in or on food it is of appropriate food grade and is prepared and handled as a food ingredient. |
| 반응성 그룹 | Ethers |
| UN 분류 | UN Hazard Class: 3UN Pack Group: III |
| Special Reports | OPDYKE DL JMONOGRAPHS ON FRAGRANCE RAW MATERIALS. ANISOLEFOOD TOXICOL 17(3) 243 (1979). A REVIEW WITH 37 REF ON ANISOLE INCLUDING TOXICITY, IRRITATION, SENSITIZATION, METAB, PHARMACOLOGY, TUMOR PROMOTING ACTIVITY, & CYTOTOXICITY.Schultz TW et alJ Appl Toxicol 13 (6): 429-34 (1993). Predicted toxicities of aryl alkanols and related compounds /including anisole to Tetrahymena pyriformis in a population growth impairment assay/. |
| Reactivity Alerts | Highly FlammablePeroxidizable Compound |
| Reactivity Profile | Ethers, such as ANISOLE can act as bases. They form salts with strong acids and addition complexes with Lewis acids. The complex between diethyl ether and boron trifluoride is an example. Ethers may react violently with strong oxidizing agents. In other reactions, which typically involve the breaking of the carbon-oxygen bond, ethers are relatively inert. |
| 소화 | Excerpt from ERG Guide 128 [Flammable Liquids (Water-Immiscible)]:CAUTION: The majority of these products have a very low flash point. Use of water spray when fighting fire may be inefficient. CAUTION: For mixtures containing alcohol or polar solvent, alcohol-resistant foam may be more effective.SMALL FIRE: Dry chemical, CO2, water spray or regular foam. If regular foam is ineffective or unavailable, use alcohol-resistant foam.LARGE FIRE: Water spray, fog or regular foam. If regular foam is ineffective or unavailable, use alcohol-resistant foam. Avoid aiming straight or solid streams directly onto the product. If it can be done safely, move undamaged containers away from the area around the fire.FIRE INVOLVING TANKS, RAIL TANK CARS OR HIGHWAY TANKS: Fight fire from maximum distance or use unmanned master stream devices or monitor nozzles. Cool containers with flooding quantities of water until well after fire is out. For petroleum crude oil, do not spray water directly into a breached tank car. This can lead to a dangerous boil over. Withdraw immediately in case of rising sound from venting safety devices or discoloration of tank. ALWAYS stay away from tanks in direct contact with flames. For massive fire, use unmanned master stream devices or monitor nozzlesif this is impossible, withdraw from area and let fire burn. (ERG, 2024)Use foam, powder, carbon dioxide. In case of fire: keep drums, etc., cool by spraying with water. |
| 응급 조치 | Fresh air, rest.Remove contaminated clothes. Rinse and then wash skin with water and soap.First rinse with plenty of water for several minutes (remove contact lenses if easily possible), then refer for medical attention.Rinse mouth. Do NOT induce vomiting. Refer for medical attention . |
| 누출 비상 조치 | · CALL 911. Then call emergency response telephone number on shipping paper. If shipping paper not available or no answer, refer to appropriate telephone number listed on the inside back cover.· Keep unauthorized personnel away.· Stay upwind, uphill and/or upstream.· Ventilate closed spaces before entering, but only if properly trained and equipped.· ELIMINATE all ignition sources (no smoking, flares, sparks or flames) from immediate area.· All equipment used when handling the product must be grounded.· Do not touch or walk through spilled material.· Stop leak if you can do it without risk.· Prevent entry into waterways, sewers, basements or confined areas.· A vapor-suppressing foam may be used to reduce vapors.· Absorb or cover with dry earth, sand or other non-combustible material and transfer to containers.· Use clean, non-sparking tools to collect absorbed material.Large Spill· Dike far ahead of liquid spill for later disposal.· Water spray may reduce vapor, but may not prevent ignition in closed spaces. |
| 응급 처치 | Excerpt from ERG Guide 128 [Flammable Liquids (Water-Immiscible)]:Refer to the "General First Aid" section. Specific First Aid: Wash skin with soap and water. In case of burns, immediately cool affected skin for as long as possible with cold water. Do not remove clothing if adhering to skin. (ERG, 2024)General First Aid:· Call 911 or emergency medical service.· Ensure that medical personnel are aware of the material(s) involved, take precautions to protect themselves and avoid contamination.· Move victim to fresh air if it can be done safely.· Administer oxygen if breathing is difficult.· If victim is not breathing:-- DO NOT perform mouth-to-mouth resuscitationthe victim may have ingested or inhaled the substance.-- If equipped and pulse detected, wash face and mouth, then give artificial respiration using a proper respiratory medical device (bag-valve mask, pocket mask equipped with a one-way valve or other device).-- If no pulse detected or no respiratory medical device available, provide continuous compressions. Conduct a pulse check every two minutes or monitor for any signs of spontaneous respirations.· Remove and isolate contaminated clothing and shoes.· For minor skin contact, avoid spreading material on unaffected skin.· In case of contact with substance, remove immediately by flushing skin or eyes with running water for at least 20 minutes.· For severe burns, immediate medical attention is required.· Effects of exposure (inhalation, ingestion, or skin contact) to substance may be delayed.· Keep victim calm and warm.· Keep victim under observation.· For further assistance, contact your local Poison Control Center.· Note: Basic Life Support (BLS) and Advanced Life Support (ALS) should be done by trained professionals.Specific First Aid:· Wash skin with soap and water. |
| 안전 보관 | Fireproof. |
| 노출 관리 및 개인 보호 | · Wear positive pressure self-contained breathing apparatus (SCBA).· Structural firefighters' protective clothing provides thermal protection but only limited chemical protection. |
| 소화 절차 | If material on fir or involved in fire: Do not extinguish fire unless flow can be stopped or safely confined. Use water in flooding quantities as fog. Solid streams of water may be ineffective. Cool all affected containers with flooding quantities of water. Apply water from as far a distance as possible. Use foam, dry chemical, or carbon dioxide. Keep run-off water out of sewers and water sources. |
| 비화재 누출 대응 | Excerpt from ERG Guide 128 [Flammable Liquids (Water-Immiscible)]:ELIMINATE all ignition sources (no smoking, flares, sparks or flames) from immediate area. All equipment used when handling the product must be grounded. Do not touch or walk through spilled material. Stop leak if you can do it without risk. Prevent entry into waterways, sewers, basements or confined areas. A vapor-suppressing foam may be used to reduce vapors. Absorb or cover with dry earth, sand or other non-combustible material and transfer to containers. Use clean, non-sparking tools to collect absorbed material.LARGE SPILL: Dike far ahead of liquid spill for later disposal. Water spray may reduce vapor, but may not prevent ignition in closed spaces. (ERG, 2024) |
| 처리 방법 | SRP: At the time of review, criteria for land treatment or burial (sanitary landfill) disposal practices are subject to significant revision. Prior to implementing land disposal of waste residue (including waste sludge), consult with environmental regulatory agencies for guidance on acceptable disposal practices. |
| 누출 처리 | Ventilation. Remove all ignition sources. Collect leaking and spilled liquid in sealable containers as far as possible. Absorb remaining liquid in sand or inert absorbent. Then store and dispose of according to local regulations. |
| Preventive Measures | If material not on fire and not involved in fire: keep sparks, flames, and other sources of ignition away. Keep material out of water sources and sewers. Build dikes to contain flow as necessary. Attempt to stop leak if without undue personnel hazard. Use water spray to knock-down vapors.Personnel protection: Avoid breathing vapors. Keep upwind. Avoid bodily contact with the material. ... Do not handle broken packages unless wearing appropriate personal protective equipment. Wash away any material which may have contacted the body with copious amounts of water or soap and water. ... If contact with the material anticipated, wear appropriate chemical protective clothing. |
| Isolation and Evacuation | Excerpt from ERG Guide 128 [Flammable Liquids (Water-Immiscible)]:IMMEDIATE PRECAUTIONARY MEASURE: Isolate spill or leak area for at least 50 meters (150 feet) in all directions.LARGE SPILL: Consider initial downwind evacuation for at least 300 meters (1000 feet).FIRE: If tank, rail tank car or highway tank is involved in a fire, ISOLATE for 800 meters (1/2 mile) in all directionsalso, consider initial evacuation for 800 meters (1/2 mile) in all directions. (ERG, 2024)Immediate precautionary measure· Isolate spill or leak area for at least 50 meters (150 feet) in all directions.· Consider initial downwind evacuation for at least 300 meters (1000 feet).· If tank, rail tank car or highway tank is involved in a fire, ISOLATE for 800 meters (1/2 mile) in all directionsalso, consider initial evacuation for 800 meters (1/2 mile) in all directions. |
| 환경 거동 | TERRESTRIAL FATE: Based on a recommended classification scheme(2), the experimentally-determined Koc value for anisole of 35(1) suggests that it will be highly mobile in soil and may leach(SRC). Its estimated Henry's Law constant(3), 4.35X10-3 atm-cu m/mole(SRC), vapor pressure, 3.4 mm Hg at 25 °C(5), and low adsorptivity to soil indicate that volatilization may be an important fate process from both moist and dry soil surfaces(4,SRC). Anisole has been demonstrated to be readily biodegradable in screening tests(6-8) and therefore may readily biodegrade in soil(SRC).AQUATIC FATE: Anisole should volatilize from water based on its estimated Henry's Law constant of 4.4X10-3 atm-cu m/mole(SRC), derived from a fragment constant estimation method(3). Estimated half-lives for a model river and model lake are 3.2 hr and 4.2 days, respectively(4,SRC). Anisole has been demonstrated to be readily biodegradable in screening tests(5,6) and therefore may biodegrade in natural water(SRC). When anisole was added to a model aquatic ecosystem with fish, mosquito larva, alga, daphnia, and snails and incubated for 24 hr, the concentration of anisole was considerably reduced (by approximately 93%) and degradation products were found in the water(1). A Russian study reported that anisole was stable in water for 4 days(2). The details of the study were not available. According to a recommended classification scheme(8), experimental bioaccumulation factors obtained from a model aquatic ecosystem along with evidence of metabolism in aquatic organisms(1) suggests that bioaccumulation of anisole should not be a concern(SRC).ATMOSPHERIC FATE: According to a theory of gas/particle partitioning of semivolatile organic compounds in the atmosphere(2), anisole, which has a vapor pressure of 3.5 mm Hg at 25 °C(3) will exist in the ambient atmosphere as a vapor(SRC). Vapor-phase anisole is degraded in the atmosphere by reaction with photochemically-produced hydroxyl radicals(SRC)the half-life for this reaction in air is estimated to be 22 hr(1,SRC). Anisole's water solubility in water is 1520 mg/L(4), and therefore it may be washed out of the atmosphere by rain(SRC). |
| 식품 조사 수치 | Anisole is a meat flavor volatile(1). |
| 유해 작용 | Neurotoxin - Acute solvent syndrome |
| 노출 경로 | The substance can be absorbed into the body by inhalation. |
| Signs and Symptoms | Burning sensation. Cough. Sore throat.Dry skin. Redness.Redness. Pain. |
| Effluent Concentrations | In a comprehensive survey of wastewater from 4000 industrial and publicly owned treatment works (POTWs) sponsored by the Effluent Guidelines Division of the U.S. EPA, anisole was identified in discharges of the following industrial category (positive occurrences, median concn in ppb): organics and plastics (564.8) and organic chemicals (3025.4)(1). The highest effluent concn in these industrial categories was 8660 ppb and 753 ppb, respectively(1). Anisole was found in 1 of 3 samples of trench leachate from the West Valley waste disposal site at a concn of 2.7 mg/L(2). Anisole was found in ponds holding wastes from olive oil production(3). It has also been detected in wastewater from coal gasification plants(4,5) and in one case reported to be 0.2 mg/L(4). Anisole was present in raw wastewater and final effluent from a dye manufacturing plant at levels of 37-190 ppb and 5-71 ppb, respectively(6). |
| Soil Adsorption/Mobility | An experimental Koc of 35 has been reported for anisole(1). Using an estimation method based on molecular connectivity indices(2), the Koc for anisole is estimated to be 118(SRC). According to a suggested classification scheme(3), these Koc values respectively suggest that anisole would be very highly mobile and highly mobile in soil and would readily leach(SRC). |
| Natural Pollution Sources | Anisole was identified as a compound isolated from essential oil of ocmum selloi.Anisole has been found in lakes in the vicinity of Mount St Helens that received pyroclastic flow resulting from the volcanic eruption(1). It may also be formed during the combustion of hydrocarbons(2-4). This suggests that anisole may be formed naturally in the environment when hydrocarbons are burned(SRC). Since anisole has been reported as a meat flavor volatile(5), it may naturally occur in meat or be formed during cooking(SRC). |
| Human Toxicity Excerpts | ... Human volunteers exposed to 200 mg/cu m /exposure time not specified/ experienced burning in the throat, irritation of the eyes and a foreign taste in the mouth. |
| Artificial Pollution Sources | Anisole may be released to the environment during its manufacture, transport, disposal, and use(SRC) as an intermediate in the manufacture of organic compounds, for example fragrances and pharmaceuticals, and as a solvent and heat transfer medium(2). Anisole is formed as an impurity in the production of o-cresol and 2,6-xylenol by the alkylation of phenol with methanol(1). Anisole may be emitted from kerosine space heaters(3) and may occur in automobile exhaust(4,5). |
| Environmental Biodegradation | In a 2-week biodegradation screening test (MITI test) using anisole (100 ppm) and an activated sludge inoculum, 56% of BOD was removed and at the end of the 2-week period there was an upward trend in BOD consumption(1). Anisole was readily biodegradable in another screening test>70% DOC and >60% BOD were removed in this test(3). Anisole completely degraded in a biodegradation test that utilized a soil inoculum(2). |
| Environmental Bioconcentration | Using its log Kow, 2.11(2), one estimates a BCF of 24 for anisole using a recommended regression equation(3). The bioconcentration of anisole in aquatic organisms was determined in a model aquatic ecosystem maintained at 26.7 °C with 12 hr of simulated daylight exposure(1). After 24 hr exposure, the ecological magnification for anisole was (organism, bioaccumulation factor): fish, 22mosquito larva, 27algae, 563daphnia, 771snails, 899(1). There were signs of considerable metabolism in all species. O-dealkylate occurred in fish and snail, hydroxylation to o- and p-methoxyphenols occurred in all species except daphnia, and conjugation occurred in alga and snails(1). According to a recommended classification scheme(4), this BCF value and its metabolism in aquatic organisms would indicate that anisole has a low potential for bioconcentration in fish and aquatic organisms(SRC). |
| 수질 위해 등급(WGK) | 2 |
| TSCA 등재 상태 | TSCA listed |
| RTECS 번호 | BZ8050000 |
| 운송 번호(UN) | UN 2222 |
| 독성 | LD50 orally in rats: 3700 mg/kg (Taylor) |
| 관세 코드 | 29093090 |
| 위험 문구(R) | 10-38-20-36/37 |
| 위험 표시 | Xn,Xi |
| 안전 문구(S) | 37/39-26-16-24/25 |
| 포장분류 | III |
| 위험 등급 | 3Flam. Liq. 3STOT SE 3 |
| 기존화학 물질 | KE-23213 |
| 자연 발화 온도 | 887 °F |
| 저장 분류 | 3 - Flammable liquids |
| 유해 물질 데이터 | 100-66-3(Hazardous Substances Data) |
용도
개요
Anisole is a colorless liquid with a spicy-sweet smell. Anisole can be produced by all the aforementioned methods. It is an important intermediate in the synthesis of organic compounds, for example fragrances and pharmaceuticals. The compound is also used as a solvent and as a heat transfer medium.
출처
Anisole is a natural product found in apple juice and in the oil of Artemisia dracunculus var. turkestanica; also reported found in butter, Camembert cheese, roasted beef, olive (Olea europae), Malay apple, Jerusalem artichoke (Helianthus tuberosus), Bourbon vanilla, truffles, crab and sopadilla fruit (Achras sapota L.).
용도
Anisole is widely used as a solvent for the synthesis of various organic compounds, anethole, nonylphenol isomer 4-(3',6'-dimethyl-3-heptyl)phenol, perfumes, insect pheromones and pharmaceuticals. It finds application in the preparation of inorganic complexes and materials such as tin-core/tin oxide nanoparticles.
일반 설명
A clear straw-colored liquid with an aromatic odor. Insoluble in water and the same density as water. Vapors heavier than air. Flash point 125°F. Boiling point 307°F. Moderately toxic by ingestion. A skin irritant. Used to make perfumes, flavorings and as a solvent.
제조 및 합성 방법
제조 방법
Anisole is synthesized by reacting phenol and dimethyl sulfate in the presence of aqueous NaOH; by passing methyl chloride into a suspension of sodium phenolate in liquid ammonia.