홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Itaconic acid → Lactic acid itaconic acid

HRID 1044466
인쇄

반응식

HRID 1044466 반응식
[C:1]([OH:6])(=[O:5])[C@H:2]([CH3:4])[OH:3].[C:7]([OH:15])(=[O:14])[C:8]([CH2:10][C:11]([OH:13])=[O:12])=[CH2:9].OCC(CO)(CO)CO.[Sn+2]>O>[C:1]([OH:6])(=[O:5])[CH:2]([CH3:4])[OH:3].[C:7]([OH:15])(=[O:14])[C:8]([CH2:10][C:11]([OH:13])=[O:12])=[CH2:9]
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

6

반응물 4

HCID 811Itaconic acidHCID 8285PentaerythritolHCID 104883Stannous cationHCID 107689L-Lactic Acid

생성물 1

HCID 86597549Lactic acid itaconic acid

시약·촉매·용매 1

HCID 962Water용매

반응 조건

온도
180 °C

실험 절차

Into a 2 liter Rotavapor equipment, used as the reactor, 437.5 g of L-lactic acid was added (88% water solution corresponding to 89 mole-%), 47.9 g of itaconic acid (9 mole-%), 14.5 g of pentaerythritol (2 mole-%) and 0.19 g of tin(II) octoate. Dry nitrogen was led into the reactor and a 500 mbar absolute pressure was established. The reactor vessel was partly immersed in an oil bath with a temperature of 90° C. The temperature of the oil bath was increased at a rate of 30° C./h to 120° C., and the reaction mixture was mixed by starting the rotation at a speed of 100 rpm. The temperature of the oil bath was evenly increased by 15° C./h until 180° C., where it was kept until the end of the polymerisation. The pressure was decreased every hour by the following steps: 500 (start)—500-450-400-350-290-190-140-90-60-50-40-30 mbar, at which pressure it was kept to the end of the polymerisation. Bubbling of nitrogen was continued throughout the polymerisation and the formed water was collected as it evolved. Total polymerisation time was 24 hours.

후처리

  1. customThe reactor vessel was partly immersed in an oil bath with a temperature of 90° C
  2. temperatureThe temperature of the oil bath was increased at a rate of 30° C./h to 120° C.
  3. additionthe reaction mixture was mixed
  4. customwhere it was kept until the end of the polymerisation
  5. waitThe pressure was decreased every hour by the following steps
  6. custom500 (start)—500-450-400-350-290-190-140-90-60-50-40-30 mbar, at which pressure it was kept to the end of the polymerisation
  7. customBubbling of nitrogen
  8. customwas continued throughout the polymerisation
  9. customthe formed water was collected as it
  10. customTotal polymerisation time

출처 및 근거

ORD 기록
ord-18c60520748747cdb4b8e368fa21c1d6
출처 데이터셋
uspto-grants-2013_10
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US08563664B2

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트