홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Trisodium citrate → 4-Phenylpyridine

HRID 1062849
인쇄

반응식

HRID 1062849 반응식
[C:1]1([Mg]Cl)[CH:6]=[CH:5][CH:4]=[CH:3][CH:2]=1.[S-]C1C=CC=CC=1.[Li+].C([C:19]1[CH:24]=[CH:23][N:22]=[CH:21][CH:20]=1)#N.C1([Mg]Cl)C=CC=CC=1.C1(S[Li])C=CC=CC=1.C([O-])(=O)CC(CC([O-])=O)(C([O-])=O)O.[Na+].[Na+].[Na+]>C1COCC1.C/C(/[O-])=C/C(C)=O.C/C(/[O-])=C/C(C)=O.[Ni+2].CP(C)C>[C:1]1([C:19]2[CH:24]=[CH:23][N:22]=[CH:21][CH:20]=2)[CH:6]=[CH:5][CH:4]=[CH:3][CH:2]=1
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

9

반응물 5

HCID 6224Trisodium citrateHCID 75064-CyanopyridineHCID 10975459Lithium thiophenolateHCID 178478979HCID 178478979, 화합물HCID 178478981HCID 178478981, 화합물

생성물 1

HCID 136514-Phenylpyridine수율 94.5%

시약·촉매·용매 3

HCID 68983Trimethylphosphine촉매
HCID 9834912Nickel(II) acetylacetonate촉매
HCID 8028Tetrahydrofuran용매

반응 조건

온도
60 °C

실험 절차

In a 1L 3-neck flask, equipped with a mechanical stirrer, were mixed phenyl magnesium chloride (96.1 mL; 192 mmol; 2.00M in THF) and lithium thiophenoxide (211 mL; 211 mmol; 1.00M THF) under a blanket of nitrogen. This mixture was heated to 60° C. for 1 h, and then cooled to 0-5° C. with an ice bath. In a separate 150 mL flask, nickel acetylacetonate (“anhydrous”; 0.617 g; 2.40 mmol; 0.025 equiv.) was dissolved under nitrogen in anhydrous THF (100 mL). To this green solution was added trimethylphosphine (4.8 mL; 4.80 mmol; 1.00M in toluene; 0.05 equiv.) forming a blue solution. After stirring for 10 min, solid 4-cyanopyridine (10.0 g; 96.1 mmol; 1 equiv.) was added to the catalyst mixture forming a green solution. This solution was added via addition funnel to the PhMgCl/PhSLi reaction solution at a rate which maintained the reaction temperature below 15° C. After the addition was complete, the reaction was heated at 60° C. for 2 h. The reaction was then allowed to cool to room temperature, and was poured into 1M aqueous sodium citrate (500 mL). The organic layer was separated and the aqueous layer extracted three times with MTBE (265 mL each). The combined organic phase was extracted three times with 2N aqueous HCl (250 mL each) and this combined aqueous extract was basified to pH≈12 with 1N aqueous NaOH. This mixture was then extracted three times with MTBE (330 mL each) and the combined organic phase was dried over anhydrous magnesium sulfate. After filtration of the drying agent, solvent was removed in vacuo leaving 14.1 g (91% yield) of 4-phenylpyridine as a light yellow solid. GC analysis of the product showed it to be >95% pure.

후처리

  1. temperaturecooled to 0-5° C. with an ice bath
  2. customforming a blue solution
  3. customforming a green solution
  4. temperaturemaintained the reaction temperature below 15° C
  5. additionAfter the addition
  6. temperaturethe reaction was heated at 60° C. for 2 h
  7. temperatureto cool to room temperature
  8. customThe organic layer was separated
  9. extractionthe aqueous layer extracted three times with MTBE (265 mL each)
  10. extractionThe combined organic phase was extracted three times with 2N aqueous HCl (250 mL each)
  11. extractionthis combined aqueous extract
  12. extractionThis mixture was then extracted three times with MTBE (330 mL each)
  13. dry with materialthe combined organic phase was dried over anhydrous magnesium sulfate
  14. filtrationAfter filtration of the drying agent, solvent
  15. customwas removed in vacuo

출처 및 근거

ORD 기록
ord-9a650e1ceab5407c9c415c71d09cdf51
출처 데이터셋
uspto-grants-2005_11
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US06962999B2

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트