홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Diisopropylamine → alpha-Amino-N-(2-hydroxy-1-methyl-2-phenylethyl)-N-methyl-1, 3-dioxolane-2-pentanamide

HRID 1067898
인쇄

반응식

HRID 1067898 반응식
C(NC(C)C)(C)C.[CH2:8]([Li])[CH2:9][CH2:10][CH3:11].[OH2:13].[OH:14][CH:15]([C:24]1[CH:29]=[CH:28][CH:27]=[CH:26][CH:25]=1)[CH:16]([N:18]([CH3:23])[C:19](=[O:22])[CH2:20][NH2:21])[CH3:17].[Cl-].[Li+].[O:32]1[CH2:36][CH2:35]CC1>>[NH2:21][CH:20]([CH2:11][CH2:10][CH2:9][CH:8]1[O:32][CH2:36][CH2:35][O:13]1)[C:19]([N:18]([CH:16]([CH3:17])[CH:15]([OH:14])[C:24]1[CH:29]=[CH:28][CH:27]=[CH:26][CH:25]=1)[CH3:23])=[O:22]
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

6

반응물 5

HCID 7912DiisopropylamineHCID 8028Tetrahydrofuran2회HCID 433294Lithium ChlorideHCID 70213195N-(2-hydroxy-1-methyl-2-phenylethyl)-N-methyl-alpha-aminoacetamide monohydrateHCID 178418339Butyllithium

생성물 1

HCID 20665105alpha-Amino-N-(2-hydroxy-1-methyl-2-phenylethyl)-N-methyl-1, 3-dioxolane-2-pentanamide

반응 조건

온도
-50 °C

실험 절차

A 0.5-1, 5-necked, round-bottom flask, equipped with an overhead stirrer, thermocouple, addition funnel and a nitrogen inlet/outlet was charged with diisopropylamine (45.52 g) and tetrahydrofuran (175 ml). After cooling to −50° C., a 2.49M solution of freshly titrated n-butyllithium in hexanes (176.7 ml) was added while maintaining the temperature at −5° C. to 21° C. This mixture was allowed to stir at 21° C. for 45 minutes and was then cooled to −5° C. This cooled solution was added to a tetrahydrofuran (700 ml, −5° C.) slurry of [R-(R*,R*)]-N-(2-hydroxy-1-methyl-2-phenylethyl)-N-methyl-α-aminoacetamide monohydrate (50 g) and lithium chloride (57.21 g, was dried in vacuo at 130° C. for 6 hours and then at 100° C. for 18 hours prior to use) maintaining the temperature in the range −7° to 7° C. After the addition was complete, the mixture was stirred for an additional hour at 0° to 3° C. 2-(3-Iodopropyl)-1,3-dioxolane (51.72 g) was added to the reaction mixture as a tetrahydrofuran (50 ml) solution over 15 minutes with agitation. The reaction was stirred for 3 hours at 0° C. until it was determined to be complete (HPLC analysis). The reaction was quenched by the addition of water (450 ml) and the tetrahydrofuran/hexane phase was separated from the lower aqueous phase and set aside. The pH of the aqueous phase was adjusted from about 11 to about 8 by the addition of concentrated hydrochloric acid (10 ml) and then extracted with methylene chloride (2×250 ml). The methylene chloride phases were combined and concentrated in vacuo (bath temperature less than or equal to 40° C.) to afford [αS-[αR*(1S*,2S*)]]-α-amino-N-(2-hydroxy-1-methyl-2-phenylethyl)-N-methyl-1,3-dioxolane-2-pentanamide as an oil (60 g). The oil was dissolved in water (300 ml) with heating and was refluxed for 12 hours until it was judged to be complete (HPLC analysis). After cooling, the reaction mixture was extracted with methylene chloride (2×250 ml) and the rich aqueous phase was concentrated in vacuo to afford the crude product as a yellow solid. The yellow solid was recrystallized from aqueous ethanol (water 75 ml, absolute ethanol 500 ml) and dried in vacuo to give 18.8 g of desired product as a white crystalline solid.

후처리

  1. customA 0.5-1, 5-necked, round-bottom flask, equipped with an overhead stirrer
  2. additionthermocouple, addition funnel and a nitrogen inlet/outlet
  3. temperaturewhile maintaining the temperature at −5° C. to 21° C
  4. temperaturewas then cooled to −5° C
  5. customwas dried in vacuo at 130° C. for 6 hours
  6. waitat 100° C. for 18 hours
  7. temperaturemaintaining the temperature in the range −7° to 7° C
  8. additionAfter the addition
  9. stirringthe mixture was stirred for an additional hour at 0° to 3° C
  10. addition2-(3-Iodopropyl)-1,3-dioxolane (51.72 g) was added to the reaction mixture as a tetrahydrofuran (50 ml) solution over 15 minutes with agitation
  11. stirringThe reaction was stirred for 3 hours at 0° C. until it
  12. customThe reaction was quenched by the addition of water (450 ml)
  13. customthe tetrahydrofuran/hexane phase was separated from the lower aqueous phase
  14. additionThe pH of the aqueous phase was adjusted from about 11 to about 8 by the addition of concentrated hydrochloric acid (10 ml)
  15. extractionextracted with methylene chloride (2×250 ml)
  16. concentrationconcentrated in vacuo (bath temperature less than or equal to 40° C.)

출처 및 근거

ORD 기록
ord-b01cbf04aca845768ff9508ef753e9f3
출처 데이터셋
uspto-grants-2001_06
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US06248882B1

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트