홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

1-Octene → 1-Octene

HRID 1178788
인쇄

반응식

HRID 1178788 반응식
[CH2:1]=[CH:2][CH2:3][CH2:4][CH2:5][CH2:6][CH2:7][CH3:8]>O>[CH2:1]=[CH:2][CH2:3][CH2:4][CH2:5][CH2:6][CH2:7][CH3:8].[CH3:1][CH2:2][CH2:3][CH2:4][CH2:5][CH2:6][CH:7]=[CH:8][CH2:1][CH2:2][CH2:3][CH2:4][CH2:5][CH3:6]
참가 물질실험 절차후처리출처 및 근거반응 노트

참가 물질

4

반응물 1

HCID 81251-Octene

생성물 2

HCID 81251-OcteneHCID 25209Tetradec-7-ene

시약·촉매·용매 1

HCID 962Water용매

실험 절차

Reactions were carried out in a 100 ml three-necked flask fitted with a reflux condenser, thermometer and septum. The reflux condenser was connected to a cooling bath to ensure a constant flow of chilled water through the jacket, thereby preventing loss of octene. The top of the condenser was connected to a cold trap and bubbler in order to monitor liquid losses and gas emissions. The thermometer was positioned below the level of the reaction solution to ensure correct temperature monitoring. The reaction flask was purged with argon to ensure removal of oxygen. The reagents [EP or PCy3, RuCl3.xH2O and 1,4-butynedioldiacetate (BDD) and 1-octene)] were added to the flask under inert conditions, then a slow hydrogen sparge (2 bubbles per second) was started and maintained during the reaction. The reaction mixture was heated, with stirring, to the desired temperature. Samples were taken at regular intervals with a syringe through the septum and quenched with a mixture of toluene and two drops of t-butylhydroperoxide. Samples were analyzed by GC using a Pona column. Unless otherwise stated, 20 ml of octene was employed in all experiments, and catalyst, solvent and additive amounts were calculated relative to this. Octadecane in an amount of 0.5 ml was used as internal standard. The conversion percentages (as molar %) of 1-octene to 7-tetradecene are provided in FIGS. 1 and 2.

후처리

  1. customReactions were carried out in a 100 ml three-necked flask
  2. customfitted with a reflux condenser
  3. customThe reflux condenser was connected to a cooling bath
  4. customThe top of the condenser was connected to a cold trap
  5. customThe reaction flask was purged with argon
  6. customremoval of oxygen
  7. additionxH2O and 1,4-butynedioldiacetate (BDD) and 1-octene)] were added to the flask under inert conditions
  8. customa slow hydrogen sparge (2 bubbles per second)
  9. temperaturemaintained during the reaction
  10. temperatureThe reaction mixture was heated
  11. customSamples were taken at regular intervals with a syringe through the septum
  12. customquenched with a mixture of toluene and two drops of t-butylhydroperoxide

출처 및 근거

ORD 기록
ord-edab9a052ff34a80bca47face338f759
출처 데이터셋
uspto-grants-2007_10
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US07276616B2

반응 노트

이 페이지에서참가 물질실험 절차후처리출처 및 근거반응 노트