홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Ethylene → Ethene propene 1-butene

HRID 1361576
인쇄

반응식

HRID 1361576 반응식
[CH2:1]=[CH:2][CH2:3][CH3:4].[CH2:5]([Al](CC(C)C)CC(C)C)[CH:6](C)C.C=CC.C=C.[Al]>[Cl-].[Cl-].C[Zr](C)(=[SiH2])(C1C2C(=C(C3C=CC=CC=3)C=CC=2)C=C1C)C1C2C(=C(C3C=CC=CC=3)C=CC=2)C=C1C.CO.C1(C)C=CC=CC=1.CCCCCC>[CH2:1]=[CH:2][CH3:3].[CH2:5]=[CH2:6].[CH2:1]=[CH:2][CH2:3][CH3:4]
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

10

반응물 5

HCID 6325Ethylene2회HCID 78441-ButeneHCID 8252PropyleneHCID 5359268AluminumHCID 16682931Triisobutylaluminum

생성물 1

HCID 168434Ethene propene 1-butene

시약·촉매·용매 4

HCID 178421807
HCID 178421807, 화합물
촉매
HCID 887Methanol용매
HCID 1140Toluene용매
HCID 8058Hexane용매

반응 조건

온도
20 °C

실험 절차

To a 4000 ml polymerization apparatus dried under reduced pressure and thoroughly purged with nitrogen, 1716 ml of dry hexane, 66.6 g of 1-butene, and triisobutylaluminum (1.0 mmol) were charged at normal temperature, then the temperature inside the polymerization apparatus was maintained at 20° C., and the polymerization apparatus was pressurized with propylene to 0.55 MPa and subsequently pressurized with ethylene to 0.80 MPa. Thereafter, a toluene solution in which 0.002 mmol of rac-dimethylsilylenebis(2-methyl-4-phenyl-indenyl)zirconium dichloride and methylaluminoxane (manufactured by Tosoh Finechem Corp.) in terms of 0.3 mmol of aluminum were contacted, was added to the polymerization vessel, and polymerization was conducted for 40 minutes while maintaining the internal temperature at 20° C. and the total pressure at 0.80 MPa by continuously supplying ethylene. The polymerization was stopped by adding 20 ml of methanol. After depressurizing, a polymer was precipitated out of the polymerization solution in 2 L of methanol, and was dried in a vacuum at 130° C. for 12 hours. The obtained polymer was 109.1 g and the polymerization activity was 163.7 kg/mmol-cat-hr. The polymer had a composition of 57.4 mol % of propylene content, 28.0 mol % of ethylene content and 14.6 mol % of 1-butene content, and had an intrinsic viscosity [η] of 2.98 dl/g.

후처리

  1. customTo a 4000 ml polymerization apparatus
  2. customdried under reduced pressure
  3. additionwere charged at normal temperature
  4. additionwas added to the polymerization vessel, and polymerization
  5. temperaturewhile maintaining the internal temperature at 20° C.
  6. customa polymer was precipitated out of the polymerization solution in 2 L of methanol
  7. customwas dried in a vacuum at 130° C. for 12 hours

출처 및 근거

ORD 기록
ord-f7ed3a07b49e49c882bcc1031473cf84
출처 데이터셋
uspto-grants-2011_02
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US07879960B2

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트