홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Ammonium Chloride → 1,6-anhydro-3,4-dideoxy-4-C-methyl-beta-D-erythrohexopyranose-2-ulose

HRID 1587107
인쇄

반응식

HRID 1587107 반응식
[Li].C[Cu]C.[CH3:5][Li].[CH2:7]1[O:14][C@@H:13]2[O:15][C@H:8]1[CH:9]=[CH:10][C:11]2=[O:12].[Cl-].[NH4+]>[Cu](I)I.CCOCC>[CH3:5][C@@H:9]1[C@H:8]2[CH2:7][O:14][C@H:13]([O:15]2)[C:11](=[O:12])[CH2:10]1
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

7

반응물 4

HCID 25517Ammonium ChlorideHCID 699486LevoglucosenoneHCID 178418348HCID 178418348, 화합물HCID 178477771HCID 178477771, 화합물

생성물 1

HCID 108555621,6-anhydro-3,4-dideoxy-4-C-methyl-beta-D-erythrohexopyranose-2-ulose수율 84.3%

시약·촉매·용매 2

HCID 83717
Copper iodide
촉매
HCID 3283Diethyl Ether용매

반응 조건

온도
-20 °C

실험 절차

To dimethyl copper lithium solution prepared by adding 66.6 g of copper iodide (350 mmol) to 500 ml of methyl lithium (1.4 N, 700 mmol) according to a general method, 50 ml of anhydrous ether solution in which 44.1 g of levoglucosenone (350 mmol) is dissolved were added dropwise at -60° C. Thereafter, the resultant solution was stirred at -60° C. for thirty minutes, and then its reaction temperature was raised to -20° C. Next, the reacted solution was poured into saturated ammonium chloride aqueous solution, followed by stirring at room temperature for an hour, The resultant solution was filtered to remove insoluble substances. Next, the organic solvent layer was separated from the obtained filtrate. The residual aqueous layer was extracted with methylene chloride to obtain an extract, This extract and the organic layer as separated before were combined. The organic layer thus combined was washed with a saturated aqueous sodium chloride solution, and dried with anhydrous magnesium sulfate. The resultant organic layer was further filtered, and the filtrate was concentrated. The obtained residue was distilled under reduced pressure, thereby yielding 41.9 g of 1,6-anhydro-3,4-dideoxy-4-C-methyl-β-D-erythrohexopyranose-2-ulose (yield: 84.3%). This product exhibited the following physical properties;

후처리

  1. dissolutionis dissolved
  2. additionwere added dropwise at -60° C
  3. customits reaction temperature
  4. filtrationThe resultant solution was filtered
  5. customto remove insoluble substances
  6. customNext, the organic solvent layer was separated from the obtained filtrate
  7. extractionThe residual aqueous layer was extracted with methylene chloride
  8. customto obtain an extract
  9. extractionThis extract
  10. customthe organic layer as separated
  11. washThe organic layer thus combined was washed with a saturated aqueous sodium chloride solution
  12. dry with materialdried with anhydrous magnesium sulfate
  13. concentrationthe filtrate was concentrated
  14. distillationThe obtained residue was distilled under reduced pressure

출처 및 근거

ORD 기록
ord-780c2ecc41e94c6185ef0e557a57acd6
출처 데이터셋
uspto-grants-1993_06
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US05216177

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트