홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Tetrabutylammonium → Methacrylic Acid

HRID 1588122
인쇄

반응식

HRID 1588122 반응식
C[O:2][C:3]([O:7][Si](C)(C)C)=[C:4]([CH3:6])[CH3:5].C([N+](CC[CH2:27][CH3:28])(CCCC)CCCC)CCC.[C:29]([O:34][Si](C)(C)C)(=[O:33])[C:30]([CH3:32])=[CH2:31].C(OCCC1C=CC=CC=1)(=[O:43])C(C)=C.C(O)(=O)C(C)=C.[CH2:59]([O:61][CH:62]([OH:71])[CH2:63][O:64][CH2:65][CH2:66][O:67]CCO)[CH3:60].O.O.O.[F-].C([N+](CCCC)(CCCC)CCCC)CCC>C1(=O)OC(C)CO1.C1COCC1.CO>[C:3]([OH:7])(=[O:2])[C:4]([CH3:6])=[CH2:5].[C:29]([OH:34])(=[O:33])[C:30]([CH3:32])=[CH2:31].[CH3:60][CH2:59][O:61][CH:62]([OH:71])[CH2:63][O:64][CH2:65][CH2:66][O:67][CH2:27][CH2:28][OH:43]
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

11

반응물 6

HCID 16028Tetrabutylammonium3회HCID 772602-Phenylethyl methacrylateHCID 552336Silane, ((1-methoxy-2-methyl-1-propenyl)oxy)trimethyl-HCID 27338392-Propenoic acid, 2-methyl-, trimethylsilyl ester2회HCID 11726816Tetrabutylammonium Fluoride TrihydrateHCID 86746980b-Ethoxytriethylene glycol methacrylate
2회

생성물 2

HCID 4093Methacrylic AcidHCID 86746980b-Ethoxytriethylene glycol methacrylate

시약·촉매·용매 3

HCID 887Methanol용매HCID 7924Propylene Carbonate용매3회HCID 8028Tetrahydrofuran용매

반응 조건

온도
30 °C

실험 절차

To a solution of 22.6 g (26.2 mL, 130 mmol) of 1-methoxy-1-trimethylsiloxy-2-methyl-1-propene and 0.1 mL of tetrabutylammonium biacetate (0.1 M in propylene carbonate) in 300 mL of THF was added dropwise 268 g (304 mL, 1.69 mole) of trimethylsilyl methacrylate. During the course of the addition the temperature of the reaction mixture rose slowly to 50° C. To increase the rate of polymerization, an additional 1.5 mL of tetrabutylammonium biacetate (0.1 M in propylene carbonate) was added in 7 portions. After all of the monomer had been added, the temperature began to fall, and the solution was cooled with a bath to 30° C. The addition of 248 g (245 mL, 1.3 mole) of 2-phenylethyl methacrylate (purified by passage over a column of basic alumina under argon) was begun. An additional 0.6 mL of tetrabutylammonium biacetate (0.1 M in propylene carbonate) was added. During the addition the temperature rose 48° C. When the addition was complete and the temperature began to fall, the solution was cooled to 31° C., 0.15 mL of tetrabutylammonium biacetate (0.1 M in propylene carbonate) was added, and 128 g (128 mL, 0.52 mole) of ethoxytriethylene glycol methacrylate (purified by passage over a column of basic alumina under argon) was added dropwise from an addition funnel. Since little temperature change was observed, an additional 0.15 mL of tetrabutylammonium biacetate (0.1 M in propylene carbonate) was added to insure completion of the polymerization. Analysis of an aliquot of the solution by 1H nmr showed that there was no residual monomer present. To the solution of poly(trimethylsilyl methacrylate [48 mol %]-b-2-phenylethyl methacrylate [37 mol %]-b-ethoxytriethylene glycol methacrylate [15 mol %]) was added 350 mL of 0.03 M tetrabutylammonium fluoride trihydrate in methanol. The resulting mixture was refluxed for 16 hr and evaporated in a rotary evaporator under reduced pressure. The residual polymer was dried for 48 hr in a vacuum oven to give 515 g of poly(methacrylic acid [48 mol %]-b-2-phenylethyl methacrylate [37 mol %]-b-ethoxytriethylene glycol methacrylate [15 mol %]). 1NMR analysis of the product showed that no trimethylsilyl ester groups remained.

후처리

  1. additionDuring the course of the addition the temperature of the reaction mixture
  2. customrose slowly to 50° C
  3. temperatureTo increase
  4. customthe rate of polymerization
  5. additionAfter all of the monomer had been added
  6. custompurified by passage over a column of basic alumina under argon)
  7. additionAn additional 0.6 mL of tetrabutylammonium biacetate (0.1 M in propylene carbonate) was added
  8. additionDuring the addition the temperature
  9. customrose 48° C
  10. additionWhen the addition
  11. temperaturethe solution was cooled to 31° C.
  12. addition0.15 mL of tetrabutylammonium biacetate (0.1 M in propylene carbonate) was added
  13. additionwas added dropwise from an addition funnel
  14. customcompletion of the polymerization
  15. temperatureThe resulting mixture was refluxed for 16 hr
  16. customevaporated in a rotary evaporator under reduced pressure
  17. customThe residual polymer was dried for 48 hr in a vacuum oven

출처 및 근거

ORD 기록
ord-b5400a2134324a16b4a94336163b0aac
출처 데이터셋
uspto-grants-1993_06
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US05219945

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트