홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Methanol → (Z)-9-Tricosene

HRID 1650006
인쇄

반응식

HRID 1650006 반응식
CO.[CH2:3](O)[CH2:4][CH2:5][CH2:6][CH2:7][CH2:8][CH2:9][CH2:10]/[CH:11]=[CH:12]\[CH2:13][CH2:14][CH2:15][CH2:16][CH2:17][CH2:18][CH2:19][CH3:20]>O>[CH3:20][CH2:19][CH2:18][CH2:17][CH2:16][CH2:15][CH2:14][CH2:13]/[CH:12]=[CH:11]\[CH2:10][CH2:9][CH2:8][CH2:7][CH2:6][CH2:5][CH2:4][CH2:3][CH2:3][CH2:4][CH2:5][CH2:6][CH3:7]
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

4

반응물 2

HCID 887MethanolHCID 5284499Oleyl Alcohol

생성물 1

HCID 5365075(Z)-9-Tricosene

시약·촉매·용매 1

HCID 962Water용매

반응 조건

온도
0 °C

실험 절차

A 12 l flask equipped with a reflux condenser, Firestone valve, mechanical stirrer, and addition funnel was flushed with N2. 500 g of oleyl alcohol and 1500 ml of tetrahydrofuran were added to the flask and the reaction mixture was cooled to 0° C. 1330 ml of n-butyllithium (1.6M in hexane) was added dropwise while maintaining the temperature below 5° C. The addition of butyllithium was completed in approximately 45 min. 420.6 g of p-toluenesulfonyl chloride was then added and the temperature was increased to 35°-40° C. using a heating mantle. The temperature was held at 40° C. for 3 hr. The reaction mixture was then cooled to 0° C. using a dry ice/isopropanol bath. 10 g of cuprous bromide was added followed by the dropwise addition of 1120 ml of n-pentylmagnesium bromide (2.5M in diethyl ether). This addition was completed in 48 min and the temperature was maintained near 0° C. during this time. The reaction mixture was stirred for 1 hr following the addition of n-pentylmagnesium bromide, then warmed to room temperature and held overnight under N2. 6.5 l of 4M HCl was added followed by phase separation. The organic phase was washed with 3 l of saturated sodium bicarbonate solution, followed by 2 volumes of a 1M KOH/MeOH solution (an aqueous KOH/MeOH solution as prepared by mixing one part of methanol and one part of water, with a final KOH concentration of 1M) the aqueous phase is then decanted. The organic solvent was removed by rotor evaporation and the residue distilled at 0.1 mm Hg vacuum. The distilled yield based on pure oleyl alcohol was 92.3%, with the final product containing 75% cis isomer.

후처리

  1. customA 12 l flask equipped with a reflux condenser
  2. additionFirestone valve, mechanical stirrer, and addition funnel
  3. customwas flushed with N2
  4. addition500 g of oleyl alcohol and 1500 ml of tetrahydrofuran were added to the flask
  5. addition1330 ml of n-butyllithium (1.6M in hexane) was added dropwise
  6. temperaturewhile maintaining the temperature below 5° C
  7. additionThe addition of butyllithium
  8. addition420.6 g of p-toluenesulfonyl chloride was then added
  9. temperaturethe temperature was increased to 35°-40° C.
  10. waitThe temperature was held at 40° C. for 3 hr
  11. temperatureThe reaction mixture was then cooled to 0° C.
  12. addition10 g of cuprous bromide was added
  13. additionfollowed by the dropwise addition of 1120 ml of n-pentylmagnesium bromide (2.5M in diethyl ether)
  14. additionThis addition
  15. waitwas completed in 48 min
  16. temperaturethe temperature was maintained near 0° C. during this time
  17. additionthe addition of n-pentylmagnesium bromide
  18. temperaturewarmed to room temperature
  19. waitheld overnight under N2
  20. addition6.5 l of 4M HCl was added
  21. customfollowed by phase separation
  22. washThe organic phase was washed with 3 l of saturated sodium bicarbonate solution
  23. customas prepared
  24. customwith a final KOH concentration of 1M) the aqueous phase is then decanted
  25. customThe organic solvent was removed by rotor evaporation
  26. distillationthe residue distilled at 0.1 mm Hg vacuum
  27. customThe distilled yield

출처 및 근거

ORD 기록
ord-e88dde01a5904621a2508902a945b9be
출처 데이터셋
uspto-grants-1990_05
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US04922049

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트