홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Iodine → (2,6-Difluoro-3-iodophenyl)methyl acetate

HRID 1732642
인쇄

반응식

HRID 1732642 반응식
FC(F)(F)C([O-])=O.FC(F)(F)C([O-])=O.FC(F)(F)C([O-])=O.[Tl+3].[C:23]([O:26][CH2:27][C:28]1[C:33]([F:34])=[CH:32][CH:31]=[CH:30][C:29]=1[F:35])(=[O:25])[CH3:24].[I:36]I.O>FC(F)(F)C(O)=O.C(OCC)C>[C:23]([O:26][CH2:27][C:28]1[C:29]([F:35])=[CH:30][CH:31]=[C:32]([I:36])[C:33]=1[F:34])(=[O:25])[CH3:24]
참가 물질실험 절차후처리출처 및 근거반응 노트

참가 물질

7

반응물 4

HCID 807IodineHCID 962WaterHCID 90200Thallium(III) trifluoroacetateHCID 12084134Acetic acid 2,6-difluorobenzyl ester

생성물 1

HCID 20304296(2,6-Difluoro-3-iodophenyl)methyl acetate수율 67.3%

시약·촉매·용매 2

HCID 3283Diethyl Ether
용매
HCID 6422Trifluoroacetic acid용매

실험 절차

Thallium tris(trifluoroacetate) (24.5 g, 0.045 mole) was added to a stirred solution of 16.8 g (0.090 mole) of (2,6-difluorophenyl)methyl acetate in 60 ml of trifluoroacetic acid. The reaction mixture was heated at 40°-50° C. for 15 minutes then 12.7 g (0.05 mole) of iodine was added. Upon complete addition the reaction mixture was heated under reflux for an additional 2 hours. The solvent was removed under reduced pressure and replaced with an equal volume of methylene chloride. The methylene chloride was removed under reduced pressure to give an oily residue. The residue was poured onto ice, using water and diethyl ether to rinse. The mixture was stirred for 30 minutes as 10 g of sodium metabisulfite and then 40 ml of a 5% aqueous solution of sodium hydroxide were added. The aqueous phase was separated and the organic phase was washed with two portions of water, one portion of a 5% aqueous solution of sodium thiosulfate, two portions of water, and finally one portion of a saturated aqueous solution of sodium chloride. The organic layer was dried with magnesium sulfate, filtered, and the filtrate concentrated under reduced pressure to give a residual oil. The oil was distilled under reduced pressure to give 10.5 g of (2,6-difluoro-3-iodophenyl)methyl acetate, b.p. 70°-80° C./2.2 mm. The nmr spectrum was consistent with the proposed structure.

후처리

  1. temperatureThe reaction mixture was heated at 40°-50° C. for 15 minutes
  2. additionUpon complete addition the reaction mixture
  3. temperaturewas heated
  4. temperatureunder reflux for an additional 2 hours
  5. customThe solvent was removed under reduced pressure
  6. customThe methylene chloride was removed under reduced pressure
  7. customto give an oily residue
  8. additionThe residue was poured onto ice
  9. washto rinse
  10. addition40 ml of a 5% aqueous solution of sodium hydroxide were added
  11. customThe aqueous phase was separated
  12. washthe organic phase was washed with two portions of water, one portion of a 5% aqueous solution of sodium thiosulfate, two portions of water, and finally one portion of a saturated aqueous solution of sodium chloride
  13. dry with materialThe organic layer was dried with magnesium sulfate
  14. filtrationfiltered
  15. concentrationthe filtrate concentrated under reduced pressure
  16. customto give a residual oil
  17. distillationThe oil was distilled under reduced pressure

출처 및 근거

ORD 기록
ord-7afdf7eba0f546c2856971ff8b93c3b2
출처 데이터셋
uspto-grants-1980_12
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US04238505

반응 노트

이 페이지에서참가 물질실험 절차후처리출처 및 근거반응 노트