홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Acrolein → Neopentyl 2-cyanopenta-2,4-dienoate

HRID 1770326
인쇄

반응식

HRID 1770326 반응식
[C:1]([CH2:3][C:4]([O:6][CH2:7][C:8]([CH3:11])([CH3:10])[CH3:9])=[O:5])#[N:2].[CH:12]([CH:14]=[CH2:15])=O>O1CCOCC1.[Cl-].[Zn+2].[Cl-]>[C:1]([C:3](=[CH:15][CH:14]=[CH2:12])[C:4]([O:6][CH2:7][C:8]([CH3:11])([CH3:10])[CH3:9])=[O:5])#[N:2]
참가 물질실험 절차후처리출처 및 근거반응 노트

참가 물질

5

반응물 2

HCID 7847AcroleinHCID 19389183Neopentyl cyanoacetate

생성물 1

HCID 53935007Neopentyl 2-cyanopenta-2,4-dienoate수율 38%

시약·촉매·용매 2

HCID 3007855Sinkkikloridi촉매HCID 312751,4-Dioxane용매3회

실험 절차

To a 1 liter, 3-necked glass reaction flask equipped with a mechanical stirrer, pressure compensating addition funnel and thermometer was added 1,4-dioxane (300 mls), zinc chloride (62.7 g; 0.46 moles), neopentyl cyanoacetate (116.25 g; 0.75 moles) and 1 ml of a solution of 1,4-hydroquinone, prepared by dissolving 1.22 g 1,4-hydroquinone in 100 mls 1,4-dioxane. The mixture was stirred and cooled by means of an ice bath, while a solution of acrolein (52.54 g; 0.94 moles) in 1,4-dioxane (200 mls) was added slowly from the addition funnel. The rate of addition was adjusted such that the reaction temperature did not exceed 40° C. After the reaction exotherm had subsided, the cooling bath was removed and the mixture stirred for a further 5 days. The solvent was removed by distillation under reduced pressure at 28° C. and 45 mbar and the reaction product was transferred to a 2-liter flask. Hexane (900 mls) was added and a yellow polymeric precipitate was formed. The hexane solution was decanted from the polymer and washed 3 times with 1200 ml portions of cold 0.1M hydrochloric acid solution, dried over anhydrous sodium sulfate and the solvent removed by distillation under reduced pressure to yield crude neopentyl 2-cyanopenta-2,4-dienoate (54.95 g; 38%) as a low viscosity orange colored liquid. The structure of the monomer was confirmed by proton NMR and IR analysis. The monomer was stabilized by the addition of 0.6 mg (approximately 10 ppm) of methane sulfonic acid. This monomer was used without further purification in the preparation of the BCPP-TMDS compositions.

후처리

  1. customTo a 1 liter, 3-necked glass reaction flask
  2. customequipped with a mechanical stirrer, pressure compensating addition funnel
  3. customprepared
  4. additionwas added slowly from the addition funnel
  5. additionThe rate of addition
  6. customdid not exceed 40° C
  7. customthe cooling bath was removed
  8. stirringthe mixture stirred for a further 5 days
  9. customThe solvent was removed by distillation under reduced pressure at 28° C.
  10. custom45 mbar and the reaction product was transferred to a 2-liter flask
  11. additionHexane (900 mls) was added
  12. customa yellow polymeric precipitate was formed
  13. customThe hexane solution was decanted from the polymer
  14. washwashed 3 times with 1200 ml portions of cold 0.1M hydrochloric acid solution
  15. dry with materialdried over anhydrous sodium sulfate
  16. customthe solvent removed by distillation under reduced pressure

출처 및 근거

ORD 기록
ord-f50e96a0ac3b4132bc324e66e529e4cd
출처 데이터셋
uspto-grants-1995_01
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US05386047

반응 노트

이 페이지에서참가 물질실험 절차후처리출처 및 근거반응 노트