홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Vinylidene fluoride → Hfp tfe

HRID 1835896
인쇄

반응식

HRID 1835896 반응식
S(OOS([O-])(=O)=O)([O-])(=O)=O.[NH4+].[NH4+].O.O.O.O.O.O.O.OP([O-])([O-])=O.[Na+].[Na+].[F:27][C:28]([F:51])([C:32]([F:50])([F:49])C(F)(F)C(F)(F)[C:35]([F:44])([F:43])[C:36](F)([F:41])[C:37]([F:40])([F:39])[F:38])C([O-])=O.[NH4+].FC(F)=C(F)F.C(F)(F)=C.FC(F)(F)C(F)=C(F)F>O.C(O)(C)C>[F:38][C:37]([F:40])([F:39])[C:36]([F:41])=[C:35]([F:44])[F:43].[F:27][C:28]([F:51])=[C:32]([F:50])[F:49]
참가 물질실험 절차후처리출처 및 근거반응 노트

참가 물질

9

반응물 6

HCID 6369Vinylidene fluorideHCID 8301TetrafluoroethyleneHCID 8302HexafluoropropyleneHCID 62648Ammonium PersulfateHCID 2776282Ammonium perfluorooctanoateHCID 6096963Phosphoric acid, disodium salt, heptahydrate

생성물 1

HCID 18927062
Hfp tfe

시약·촉매·용매 2

HCID 962Water용매HCID 3776Isopropanol용매

실험 절차

A VF2/HFP/TFE fluoroelastomer was prepared by a continuous emulsion polymerization process of the prior art in a well-stirred 4.0-liter stainless steel liquid full reaction vessel at 115° C. An aqueous solution, consisting of 3.59 g/hour (g/h) ammonium persulfate, 8.30 g/h sodium phosphate dibasic heptahydrate, 7.20 g/h ammonium perfluorooctanoate, and 2.30 g/h isopropanol in deionized water, was fed to the reactor at a rate of 10 L/hour. The reactor was maintained at a liquid-full level at a pressure of 6.2 MPa by means of a back-pressure control valve in the effluent line. After 30 minutes, polymerization was initiated by introduction of a gaseous monomer mixture consisting of 584 g/h tetrafluoroethylene (TFE), 1103 g/h vinylidene fluoride (VF2), and 921 g/h hexafluoropropylene (HFP) fed through a diaphragm compressor. After 2.0 hours, collection of the resulting fluoroelastomer latex was begun and continued for 6 hours. The latex, which had a pH of 3.5 and contained 19.3 wt. % solids, was separated from residual monomers in a degassing vessel at atmospheric pressure. Fluoroelastomer crumb product was isolated using aluminum sulfate solution. The coagulated fluoroelastomer polymer was allowed to settle, supernatant serum was removed, and the polymer was washed by reslurrying in water three times before filtering. The wet crumb was dried in an air oven at approximately 50°-65° C. to a moisture content of less than 1 wt. %. About 14 kg of fluoroelastomer was recovered at an overall conversion of 92.2%. The product, containing 24.0 wt. % TFE units, 44.3 wt. % VF2 units, and 31.7 wt. % HFP units, was an amorphous elastomer having a glass transition temperature of −12° C., as determined by DSC (heating mode, 10° C./minute, inflection point of transition). Inherent viscosity of the elastomer was 0.79 dL/g, measured at 30° C. in methyl ethyl ketone, and Mooney viscosity, ML (1+10), was 64.

후처리

  1. temperatureThe reactor was maintained at a liquid-full level at a pressure of 6.2 MPa by means of a back-pressure control valve in the effluent line
  2. custompolymerization
  3. waitAfter 2.0 hours
  4. customcollection of the resulting fluoroelastomer
  5. waitcontinued for 6 hours
  6. customwas separated from residual monomers in a degassing vessel at atmospheric pressure

출처 및 근거

ORD 기록
ord-696f914b79e947d38934833443eb5e28
출처 데이터셋
uspto-grants-2004_08
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US06774164B2

반응 노트

이 페이지에서참가 물질실험 절차후처리출처 및 근거반응 노트