홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Ethanol → water TEOS

HRID 2073699
인쇄

반응식

HRID 2073699 반응식
[CH2:1]([O:3][Si:4]([O:11][CH2:12][CH3:13])([O:8][CH2:9][CH3:10])[O:5][CH2:6][CH3:7])[CH3:2].C(O)C.[N+]([O-])(O)=O>O>[OH2:3].[CH2:6]([O:5][Si:4]([O:8][CH2:9][CH3:10])([O:3][CH2:1][CH3:2])[O:11][CH2:12][CH3:13])[CH3:7]
참가 물질실험 절차후처리출처 및 근거반응 노트

참가 물질

5

반응물 3

HCID 702EthanolHCID 944Nitric AcidHCID 6517Tetraethoxysilane

생성물 1

HCID 87705869water TEOS

시약·촉매·용매 1

HCID 962Water용매

실험 절차

A sol is formed by mixing 520 grams of tetraethoxysilane (TEOS) with 235 grams of reagent grade ethanol at 60° to 65° C. A solution of 1.6 grams of nitric acid in 78.5 grams of deionized water is added to the sol in four increments at about 15 minute intervals, producing a sol with a water/TEOS molar ratio of 1.75. The tetraethoxysilane is allowed to hydrolyze for one hour at 60° to 65° C. The sol is then allowed to cool to ambient temperature. The sol is vacuum distilled at 50° C. in a rotary evaporator. After distillation, the sol is rediluted with ethanol to a solids content of 53 percent. The sol is then aged until it reaches the desired spinning viscosity. The sol is placed in a sealed reservoir pressurized with 30 pounds per square inch of helium. The pressure forces the sol into a gear driven pump which delivers the sol to a spinnerette. The sol is continuously extruded through a 4-hole spinnerette with hole diameters of 280 microns. The continuously extruded fibers are drawn vertically downward through a spin tube about 9 feet (about 2.74 meters) long containing an atmosphere comprising ammonia in air. The concentration of NH3 is about 19,000 parts per million. After brief exposure to ammonia, the continuous fibers are non-tacky. The continuous non-tacky fibers are brought together by a guide to form a single compact strand. The continuous strand is then gathered on a take-up winder. After the strand is collected, it is fired to form the final silica fiber product. In this example, the fibers are placed in an oven programmed to raise the temperature 15° C. per minute. During this heating cycle, 200 cubic centimeters per minute of oxygen is introduced into the oven until the temperature reaches 500° C. The temperature is further raised to 850° C., at which the fibers are held for 5 minutes.

후처리

  1. customA sol is formed

출처 및 근거

ORD 기록
ord-3d4995c2a0b8487fbfa7a422835a1328
출처 데이터셋
uspto-grants-1990_04
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US04919871

반응 노트

이 페이지에서참가 물질실험 절차후처리출처 및 근거반응 노트