홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Triethylamine → 2,2,6,6-Tetramethylpiperidin-4-ol 2-butyl-2-ethyl-1,3-propanediol phosphite

HRID 2117725
인쇄

반응식

HRID 2117725 반응식
[CH3:1][C:2]1([CH3:11])[CH2:7][CH:6]([OH:8])[CH2:5][C:4]([CH3:10])([CH3:9])[NH:3]1.C(N(CC)CC)C.[CH2:19]([C:23]([CH2:28][CH3:29])([CH2:26][OH:27])[CH2:24][OH:25])[CH2:20][CH2:21][CH3:22].[P:30](Cl)([O-:32])[O-:31].P(Cl)([O-])[O-:35]>C1(C)C=CC=CC=1>[CH3:1][C:2]1([CH3:11])[CH2:7][CH:6]([OH:8])[CH2:5][C:4]([CH3:10])([CH3:9])[NH:3]1.[CH2:19]([C:23]([CH2:28][CH3:29])([CH2:24][OH:25])[CH2:26][OH:27])[CH2:20][CH2:21][CH3:22].[P:30]([O-:32])([O-:35])[O-:31]
참가 물질실험 절차후처리출처 및 근거반응 노트

참가 물질

6

반응물 4

HCID 8471TriethylamineHCID 754714-Hydroxy-2,2,6,6-tetramethylpiperidine2회HCID 22015288ChlorophosphiteHCID 866083742-Butyl-2-ethyl-1,3-propanediol chlorophosphite

생성물 1

HCID 866083732,2,6,6-Tetramethylpiperidin-4-ol 2-butyl-2-ethyl-1,3-propanediol phosphite

시약·촉매·용매 1

HCID 1140
Toluene
용매

실험 절차

Into a one liter, four-necked, round-bottom reaction flask was weighed 69.2 grams (0.44 mole) of 2,2,6,6-tetramethylpiperidin-4-ol, 101.2 grams (1.00 mole) of triethylamine and 250 grams of toluene. The flask was equipped with a stir shaft and paddle, temperature probe, dropping funnel, and nitrogen inlet. The reaction mixture was placed under a nitrogen blanket. Most of the 2,2,6,6-tetramethylpiperidin-4-ol was soluble in the solvents at room temperature. 2-Butyl-2-ethyl-1,3-propanediol-chlorophosphite (89.9 grams (0.40 mole)) was weighed into the dropping funnel and then slowly added to the reaction flask. White solids formed immediately. The chlorophosphite was added at a rate of addition such that the reaction temperature stayed between 18 and 22° C. Occasional cooling with an ice bath was necessary to keep the temperature under control. The total addition time was 30 minutes. The ice bath was removed and the mixture was allowed to warm slowly to room temperature. Fifty grams of additional toluene was added to rinse the dropping funnel. The white solids were waxy and difficult to stir at 18° C. After two hours, the mixture was heated to a temperature of 65° C., and stirring was continued for another hour. The mixture was then heated to 80° C. and held there for one hour to ensure the reaction is complete. The mixture was cooled to room temperature and vacuum-filtered to remove any solids. The clear filtrate was evaporated to dryness under vacuum. The product was obtained as a pale yellow liquid. (Yield: 122.8 grams) (GC Purity: 98%). The product was analyzed by 31P-NMR analysis, giving a characteristic signal with a shift of δ=125 ppm.

후처리

  1. customInto a one liter, four-necked, round-bottom reaction flask was weighed
  2. customThe flask was equipped with a stir shaft and paddle, temperature probe
  3. customwas soluble in the solvents at room temperature
  4. additionslowly added to the reaction flask
  5. customWhite solids formed immediately
  6. customstayed between 18 and 22° C
  7. temperatureOccasional cooling with an ice bath
  8. additionThe total addition time
  9. customThe ice bath was removed
  10. additionFifty grams of additional toluene was added
  11. washto rinse the dropping funnel
  12. waitAfter two hours
  13. temperaturethe mixture was heated to a temperature of 65° C.
  14. stirringstirring
  15. waitwas continued for another hour
  16. temperatureThe mixture was then heated to 80° C.
  17. waitheld there for one hour
  18. temperatureThe mixture was cooled to room temperature
  19. filtrationvacuum-filtered
  20. customto remove any solids
  21. customThe clear filtrate was evaporated to dryness under vacuum
  22. customThe product was obtained as a pale yellow liquid
  23. customgiving a characteristic signal with a shift of δ=125 ppm

출처 및 근거

ORD 기록
ord-978124c32435424e8afb456d0530124e
출처 데이터셋
uspto-grants-2008_10
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US07442732B2

반응 노트

이 페이지에서참가 물질실험 절차후처리출처 및 근거반응 노트