홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Tetrahydrofuran → alpha-Amino-N-(2-hydroxy-1-methyl-2-phenylethyl)-N-methyl-1, 3-dioxolane-2-pentanamide

HRID 2269694
인쇄

반응식

HRID 2269694 반응식
[Cl-].[Li+].O1CCCC1.O.[OH:9][CH:10]([C:19]1[CH:24]=[CH:23][CH:22]=[CH:21][CH:20]=1)[CH:11]([N:13]([CH3:18])[C:14](=[O:17])[CH2:15][NH2:16])[CH3:12].I[CH2:26][CH2:27][CH2:28][CH:29]1[O:33][CH2:32][CH2:31][O:30]1>O>[NH2:16][CH:15]([CH2:26][CH2:27][CH2:28][CH:29]1[O:33][CH2:32][CH2:31][O:30]1)[C:14]([N:13]([CH:11]([CH3:12])[CH:10]([OH:9])[C:19]1[CH:24]=[CH:23][CH:22]=[CH:21][CH:20]=1)[CH3:18])=[O:17]
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

6

반응물 4

HCID 8028Tetrahydrofuran2회HCID 433294Lithium ChlorideHCID 5521552-(3-Iodopropyl)-1,3-dioxolaneHCID 70213195N-(2-hydroxy-1-methyl-2-phenylethyl)-N-methyl-alpha-aminoacetamide monohydrate

생성물 1

HCID 20665105alpha-Amino-N-(2-hydroxy-1-methyl-2-phenylethyl)-N-methyl-1, 3-dioxolane-2-pentanamide

시약·촉매·용매 1

HCID 962
Water
용매

반응 조건

온도
-78 °C

실험 절차

A 0.5 liter, 4-necked, round-bottom flask, equipped with an overhead stirrer, thermocouple, addition funnel and a nitrogen inlet/outlet was charged with 11.4 g of lithium chloride (dried in vacuo at 130° C. for 6 hours and then at 100° C. for 18 hours prior to use), 9.1 g of diisoproylamine and 80 ml of tetrahydrofuran. After cooling to −78° C., a 2.5 M solution of n-butyllithium in hexanes (35 ml) was added over about 20 minutes while maintaining the temperature at less than or equal to −60° C. This mixture was allowed to stir at −78° C. for 45 minutes. A tetrahydrofuran solution of [R-(R*,R*)]-N-(2-hydroxy-1-methyl-2-phenylethyl)-N-methyl-α-aminoacetamide monohydrate [10 g., 0.04 mol, prepared as described by Myers et al., Tetrahedron Letters, Vol. 36, p. 4555-4558 (1995)] was added over 50 minutes while maintaining the temperature at less than or equal to−68° C. After the addition was complete, the mixture was stirred for an additional 45 minutes. The solution was allowed to warm to about 0° C. and held at that temperature for 45 minutes. The 2-(3-iodopropyl)-1,3-dioxolane (12g) from part (a) was added as a tetrahydrofuran (10 ml) solution in one portion. After 3 hours reaction time at 0° C., TLC analysis indicated no observable starting material present and water (100 ml) was added as a quench. The tetrahydrofuran/hexane phase was separated from the lower aqueous phase. The aqueous phase was extracted with methylene chloride (4×100 ml). The methylene chloride phases were combined with the tetrahydrofuran/hexane phase and washed with 100 ml of brine. After drying over sodium sulfate and filtration, concentration in vacuo (bath temperature less than or equal to 40° C.) afforded an oil (9.57g). The oil was chromatographed over silica gel 60 (column size: 3.5 cm×21 cm) eluting with 5% triethylamine in methylene chloride, collecting 100 ml fractions. Fractions number 6 through 12 were combined and concentrated in vacuo (bath temperature less than or equal to 45° C.) to afford an oil. This oil was dissolved in toluene (100 ml) and concentrated to remove residual triethylamine and give 4.54 g of the desired product as an oil.

후처리

  1. customA 0.5 liter, 4-necked, round-bottom flask, equipped with an overhead stirrer
  2. additionthermocouple, addition funnel and a nitrogen inlet/outlet
  3. customdried in vacuo at 130° C. for 6 hours
  4. additiona 2.5 M solution of n-butyllithium in hexanes (35 ml) was added over about 20 minutes
  5. temperaturewhile maintaining the temperature at less than or equal to −60° C
  6. temperaturewhile maintaining the temperature at less than or
  7. custom68° C
  8. additionAfter the addition
  9. stirringthe mixture was stirred for an additional 45 minutes
  10. temperatureto warm to about 0° C.
  11. waitheld at that temperature for 45 minutes
  12. customAfter 3 hours reaction time at 0° C.
  13. customThe tetrahydrofuran/hexane phase was separated from the lower aqueous phase
  14. extractionThe aqueous phase was extracted with methylene chloride (4×100 ml)
  15. washwashed with 100 ml of brine
  16. dry with materialAfter drying over sodium sulfate and filtration, concentration in vacuo (bath temperature less than or equal to 40° C.)

출처 및 근거

ORD 기록
ord-6defe82295784032a1e3ed19d8aa7838
출처 데이터셋
uspto-grants-2001_12
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US06329542B1

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트