홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Acetone → 4-(Epoxyethyl)benzenesulfonylazide

HRID 267179
인쇄

반응식

HRID 267179 반응식
[N-:1]=[N+:2]=[N-:3].[Na+].[CH3:5][C:6]([CH3:8])=[O:7].C=CC1[CH:16]=[CH:15][C:14]([S:17](Cl)(=[O:19])=[O:18])=[CH:13][CH:12]=1.C(Cl)Cl>O>[O:7]1[CH:6]([C:8]2[CH:16]=[CH:15][C:14]([S:17]([N:1]=[N+:2]=[N-:3])(=[O:19])=[O:18])=[CH:13][CH:12]=2)[CH2:5]1
참가 물질실험 절차후처리출처 및 근거반응 노트

참가 물질

6

반응물 4

HCID 180AcetoneHCID 6344DichloromethaneHCID 33557Sodium AzideHCID 9855777Styrene-4-sulfonyl chloride

생성물 1

HCID 203005554-(Epoxyethyl)benzenesulfonylazide

시약·촉매·용매 1

HCID 962Water용매2회

실험 절차

To a slurry of 17.5 parts of sodium azide in 20 parts of water and 40 parts of acetone at room temperature was added with rapid stirring a solution of 18 parts of p-styrenesulfonyl chloride in 61 parts of methylene chloride. After stirring at room temperature for 18 hours the orange-colored reaction mixture was diluted with 150 parts of water and separated. The water layer was re-extracted with 61 parts of methylene chloride and then the combined methylene chloride layers were washed with water and dried over magnesium sulfate. After removal of the methylene chloride solvent 12 parts of the resulting p-styrenesulfonyl azide was dissolved in 110 parts of glacial acetic acid containing one part of sodium acetate at 20°C. To the solution was added with agitation 40% peracetic acid in an amount in excess of that required to convert the styrene group to an epoxy ethyl benzene group. The reaction was allowed to come to room temperature and stirred until the peracetic acid content remained constant. Then it was diluted with 250 parts of water and 133 parts of methylene chloride. The methylene chloride layer was removed and washed 6 times with water and then dried over sodium sulfate. The methylene chloride solvent was removed to give 12.5 parts of 4-(epoxyethyl)benzenesulfonyl azide. The product was analyzed by infrared analysis for azide nitrogen and oxirane oxygen. The results of this analysis are tabulated below:

후처리

  1. customseparated
  2. extractionThe water layer was re-extracted with 61 parts of methylene chloride
  3. washthe combined methylene chloride layers were washed with water
  4. dry with materialdried over magnesium sulfate
  5. customAfter removal of the methylene chloride solvent 12 parts of the resulting p-styrenesulfonyl azide
  6. dissolutionwas dissolved in 110 parts of glacial acetic acid containing one part of sodium acetate at 20°C
  7. additionTo the solution was added with agitation 40% peracetic acid in an amount in excess of
  8. customto come to room temperature
  9. stirringstirred until the peracetic acid content
  10. additionThen it was diluted with 250 parts of water and 133 parts of methylene chloride
  11. customThe methylene chloride layer was removed
  12. washwashed 6 times with water
  13. dry with materialdried over sodium sulfate
  14. customThe methylene chloride solvent was removed

출처 및 근거

ORD 기록
ord-48ea872812aa4985bebdfbdafd0d7610
출처 데이터셋
uspto-grants-1976_03
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US03941751

반응 노트

이 페이지에서참가 물질실험 절차후처리출처 및 근거반응 노트