홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

tert-Butylacrylamide → vinyl acetate N-t-butyl acrylamide

HRID 614439
인쇄

반응식

HRID 614439 반응식
[C:1]([O:4][CH:5]=[CH2:6])(=[O:3])[CH3:2].[C:7]([NH:11][C:12](=[O:15])[CH:13]=[CH2:14])([CH3:10])([CH3:9])[CH3:8].C(OOC(C)(C)C)(=O)C(C)(C)C.C(NC(=O)C=C)CCC>CO.O>[C:1]([O:4][CH:5]=[CH2:6])(=[O:3])[CH3:2].[C:7]([NH:11][C:12](=[O:15])[CH:13]=[CH2:14])([CH3:10])([CH3:9])[CH3:8]
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

7

반응물 4

HCID 7877tert-Butylacrylamide2회HCID 7904Vinyl Acetate2회HCID 61238tert-BUTYL PEROXYPIVALATE3회HCID 642908n-Butyl-2-propenamide

생성물 1

HCID 86736402vinyl acetate N-t-butyl acrylamide

시약·촉매·용매 2

HCID 887Methanol
용매
3회
HCID 962Water용매

반응 조건

온도
50 °C

실험 절차

A 2-liter separable flask equipped with a stirring device, a condenser, a thermometer and three metering pumps was used as a polymerization reactor, and charged with 200 ml of methanol, 25.8 g (0.3 mole) of vinyl acetate, and 10.7 g (0.08 mole) of N-t-butyl acrylamide in an atmosphere of nitrogen. With stirring, the temperature of the reaction system was raised to 50° C. When the temperature of the reaction system reached 50° C., 3.48 g (0.02 mole) of t-butyl peroxypivalate was added, and the copolymerization was started. The copolymerization was continued while continuously feeding 172.2 g (2.0 moles) of vinyl acetate from a first metering pump for 2 hours at a rate of 1 mole/hr, a solution of 366.3 g (2.88 moles) of N-t-butyl acrylamide in 800 ml of methanol from a second metering pump for 2 hours and 20 minutes so that the rate of N-butyl acrylamide fed was 1 mole/hr, and a solution of 6.97 g (0.04 mole) of t-butyl peroxypivalate in 200 ml of methanol from a third metering pump for 2.5 hours so that the feed rate of the t-butyl peroxypivalate became 0.01 mole/hr. The copolymerization proceeded while maintaining a homogeneous system. After the copolymerization for 2.5 hours, the polymerization reaction mixture was poured into a large amount of water. The resulting copolymer precipitated and came afloat on the surface of the water. The copolymer was collected, washed thoroughly with water, pulverized by a mixer into a powder, collected by filtration, and dried at 40° C. in vacuo. The amount of the vinyl acetate/N-t-butyl acrylamide copolymer so obtained was 465 g. NMR spectroscopy in deuterochloroform showed that the N-t-butyl acrylamide unit content of the copolymer was 51 mole%.

후처리

  1. customA 2-liter separable flask equipped with a stirring device, a condenser
  2. customa thermometer and three metering pumps was used as a polymerization reactor
  3. customreached 50° C.
  4. customfor 2 hours
  5. custom20 minutes
  6. temperaturewhile maintaining a homogeneous system
  7. customAfter the copolymerization for 2.5 hours
  8. customthe polymerization reaction mixture
  9. customThe resulting copolymer precipitated
  10. customThe copolymer was collected
  11. washwashed thoroughly with water
  12. filtrationcollected by filtration
  13. customdried at 40° C. in vacuo

출처 및 근거

ORD 기록
ord-c0fb47afb50a453895c2c55e6915411f
출처 데이터셋
uspto-grants-1979_03
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US04144388

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트