홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Sodium Carbonate → 4-Methyl-4-(methyldisulfanyl)pentanoic acid

HRID 78554
인쇄

반응식

HRID 78554 반응식
[SH:1][C:2]([CH3:9])([CH3:8])[CH2:3][CH2:4][C:5]([OH:7])=[O:6].C(=O)([O-])[O-].[Na+].[Na+].[CH3:16][S:17]S(C)(=O)=O>O.C(O)C>[CH3:8][C:2]([S:1][S:17][CH3:16])([CH3:9])[CH2:3][CH2:4][C:5]([OH:7])=[O:6]
참가 물질실험 절차후처리출처 및 근거반응 노트

참가 물질

6

반응물 3

HCID 10340Sodium CarbonateHCID 18064S-Methyl methanethiosulfonate2회HCID 115791564-Mercapto-4-methylpentanoic acid

생성물 1

HCID 115646344-Methyl-4-(methyldisulfanyl)pentanoic acid수율 70%

시약·촉매·용매 2

HCID 702Ethanol용매HCID 962
Water
용매

실험 절차

A solution of mercaptopentanoic acid 7 (6.0 mL, 40 mmol) was dissolved in 50 mL of deionized water in a 250 mL flask. The solution was magnetically stirred as sodium carbonate (6.4 g, 60 mmol) was added to the acid at a rate that would not cause excessive frothing. The flask was equipped with a 100 mL addition funnel, which was charged with a solution of methyl methanethiolsulfonate (7.5 g, 60 mmol) dissolved in 30 mL of glass-distilled 100% ethanol. The flask was cooled in an ice/water bath and the system was maintained under an argon atmosphere. The methyl methanethiolsulfonate solution was added drop-wise to the flask as rapidly as possible but without causing excessive frothing. The cooling bath was removed and the reaction mixture was allowed to stir for an additional 3 hours. Solvent was removed by rotary evaporation under vacuum, until approximately 20 mL remained. After which 10 mL of saturated sodium bicarbonate and 30 mL of deionized water were added. The mixture was washed three times with 25 mL portions of ethyl acetate in a separatory funnel. The aqueous layer was adjusted to approximately pH 2 with 5 M HCl and was extracted twice with 120 mL portions of ethyl acetate. The organic layers were combined and washed with 20 mL of a solution composed of saturated NaCl and 1M HCl at a ratio of 4:1. The organic layer was then dried over 14 g of anhydrous sodium sulfate and solvent was removed by rotary evaporation under vacuum to give 5.4 g of product 8 (70% yield). The material can be taken to the next step without further purification. 1H NMR (CDCl3): δ1.54 (6H, s), 2.15-2.21 (2H, m), 2.64 (3H, s), 2.69-2.72 (2H, m). MS (M+Na+) calc.: 217.0, found: 217.1

후처리

  1. additionwas added to the acid at a rate that would not
  2. customThe flask was equipped with a 100 mL addition funnel
  3. temperatureThe flask was cooled in an ice/water bath
  4. temperaturethe system was maintained under an argon atmosphere
  5. customThe cooling bath was removed
  6. customSolvent was removed by rotary evaporation under vacuum, until approximately 20 mL
  7. additionAfter which 10 mL of saturated sodium bicarbonate and 30 mL of deionized water were added
  8. washThe mixture was washed three times with 25 mL portions of ethyl acetate in a separatory funnel
  9. extractionwas extracted twice with 120 mL portions of ethyl acetate
  10. washwashed with 20 mL of a solution
  11. dry with materialThe organic layer was then dried over 14 g of anhydrous sodium sulfate and solvent
  12. customwas removed by rotary evaporation under vacuum

출처 및 근거

ORD 기록
ord-a8b8fd4a1a4d4796877a486b3166cac4
출처 데이터셋
uspto-grants-2014_09
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US08841425B2

반응 노트

이 페이지에서참가 물질실험 절차후처리출처 및 근거반응 노트