홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Ethylene Glycol → Ethylene 4,4'-biphenyldicarboxylate

HRID 846828
인쇄

반응식

HRID 846828 반응식
[C:1]1([C:11]2[CH:16]=[CH:15][C:14]([C:17]([O:19][CH3:20])=[O:18])=[CH:13][CH:12]=2)[CH:6]=[CH:5][C:4]([C:7]([O:9][CH3:10])=[O:8])=[CH:3][CH:2]=1.C1(C2C=CC(C(OC)=O)=CC=2)C=CC=C(C(OC)=O)C=1.C(O)CO>CC(C)[O-].CC(C)[O-].CC(C)[O-].CC(C)[O-].[Ti+4]>[C:11]12[C:1]3[CH:6]=[CH:5][C:4](=[CH:3][CH:2]=3)[C:7](=[O:8])[O:9][CH2:10][CH2:20][O:19][C:17](=[O:18])[C:14]([CH:15]=[CH:16]1)=[CH:13][CH:12]=2
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

5

반응물 3

HCID 174Ethylene GlycolHCID 13099Dimethyl 4,4'-biphenyldicarboxylateHCID 108747(1,1'-Biphenyl)-3,4'-dicarboxylic acid, 3,4'-dimethyl ester

생성물 1

HCID 67910781Ethylene 4,4'-biphenyldicarboxylate

시약·촉매·용매 1

HCID 11026Titanium isopropoxide촉매

반응 조건

온도
260 °C

실험 절차

A clear solution of 243.3 g (0.900 mole) of dimethyl 4,4'-biphenyldicarboxylate, 81.2 g of dimethyl 3,4'-biphenyldicarboxylate, 150.5 g (2.43 mole) of ethylene glycol and 50 μL of titanium tetraisopropoxide is stirred at 217° C. under nitrogen in a 1-L round bottom flask equipped with a paddle stirrer, Vigreaux column, distillation head, condenser, receiver and nitrogen inlet. The apparatus is heated in a molten salt bath until methanol begins to distill. After 2.7 hours, the temperature is slowly increased to 260° C. where it is held for 45 minutes. The distillate (104 mL) that has collected is discarded. Over the next 48 minutes the temperature is increased to 300° C. and the pressure is slowly reduced to 1 mm Hg. More liquid is distilled. The viscosity of the clear reaction mass slowly increases. After 8 minutes at 300° C., the heating bath is lowered and nitrogen is admitted. The polymer solidifies to an opaque creamy white solid when it cools. It is ground to coarse granules in a Wiley mill. The copolyester has an inherent viscosity of 0.72 dL/g, a Tg of 122° C. and a Tm of 293° C. The molecular weight of this polymer is advanced in the solid state by stirring the granules at 240° C. and 1 mm Hg for 3.2 hours. The advanced polymer has an inherent viscosity of 1.05 dL/g. It is injection molded into standard one eight-inch thick test bars at 316° C. into a mold held at 65° C. using an Arburg 170CDM injection molding machine. The tensile modulus and impact strength of these test bars are measured using procedures described in ASTM Test Nos. D638 and D256, respectively. The tensile modulus is 578 kpsi and the notched Izod impact strength is 1.2 ft. lb./in.

후처리

  1. customequipped with a paddle stirrer
  2. distillationVigreaux column, distillation head, condenser, receiver and nitrogen inlet
  3. temperatureThe apparatus is heated in a molten salt bath until methanol
  4. distillationto distill
  5. waitis held for 45 minutes
  6. distillationThe distillate (104 mL) that has collected
  7. temperatureOver the next 48 minutes the temperature is increased to 300° C.
  8. distillationMore liquid is distilled
  9. temperatureThe viscosity of the clear reaction mass slowly increases
  10. waitAfter 8 minutes at 300° C.
  11. customa Tm of 293° C
  12. wait1 mm Hg for 3.2 hours
  13. custommolded into standard one eight-inch thick test bars at 316° C. into a mold
  14. customheld at 65° C.

출처 및 근거

ORD 기록
ord-b12b9b51348f4fafadf247cbce024451
출처 데이터셋
uspto-grants-1992_08
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US05138022

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트