홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Diisopropylamine → 1-(3-Methoxyphenyl)-2-pyridin-4-ylethane-1,2-diol

HRID 862198
인쇄

반응식

HRID 862198 반응식
C(NC(C)C)(C)C.C([Li])CCC.[Si]([O:20][CH2:21][C:22]1[CH:27]=[CH:26][N:25]=[CH:24][CH:23]=1)(C(C)(C)C)(C)C.[CH:28](=[O:37])[C:29]1[CH:34]=[CH:33][CH:32]=[C:31]([O:35][CH3:36])[CH:30]=1.C(=O)([O-])O.[Na+]>O1CCCC1>[CH3:36][O:35][C:31]1[CH:30]=[C:29]([CH:28]([OH:37])[CH:21]([C:22]2[CH:23]=[CH:24][N:25]=[CH:26][CH:27]=2)[OH:20])[CH:34]=[CH:33][CH:32]=1
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

7

반응물 5

HCID 7912DiisopropylamineHCID 115693-MethoxybenzaldehydeHCID 516892Sodium BicarbonateHCID 109878804-(Tert-butyldimethylsilyloxymethyl)pyridineHCID 178418339Butyllithium

생성물 1

HCID 187047701-(3-Methoxyphenyl)-2-pyridin-4-ylethane-1,2-diol

시약·촉매·용매 1

HCID 8028Tetrahydrofuran용매4회

반응 조건

온도
-20 °C

실험 절차

To a stirring solution of diisopropylamine (4.5 g, 5.8 mL, 44 mmol) in tetrahydrofuran (170 mL) at -78° C. was added n-butyllithium (17.7 mL of a 2.5M solution in tetrahydrofuran) dropwise. After ten minutes, a solution of 4-pyridylcarbinol t-butyldimethylsilyl ether (9.0 g, 40 mmol) in tetrahydrofuran (35 mL) was added dropwise, and the temperature allowed to rise to -15° C. The solution was recooled to -78° C. and to it was added a solution of 3-anisaldehyde (5.5 g, 4.9 mL, 40 mmol) in tetrahydrofuran (35 mL) dropwise. The solution was allowed to warm to -20° C. and poured into saturated aqueous sodium hydrogen carbonate (300 mL). The aqueous layer was extracted with ethyl acetate (3×200 mL) and the organic layers were combined, dried over anhydrous magnesium sulfate, filtered and concentrated at reduced pressure. The resulting oil was dissolved in tetrahydrofuran (120 mL) and to this solution was added tetrabutylammonium fluoride (48 mL of a 1.0M solution in tetrahydrofuran) dropwise. After ten minutes, the reaction mixture was concentrated at reduced pressure and the resulting oil was chromatographed on silica gel eluting with 97:3 ethyl acetate:methanol to give a mixture of diastereomeric diols as a foam (8.5 g) which was used without further purification.

후처리

  1. waitAfter ten minutes
  2. customto rise to -15° C
  3. customwas recooled to -78° C. and to it
  4. extractionThe aqueous layer was extracted with ethyl acetate (3×200 mL)
  5. dry with materialdried over anhydrous magnesium sulfate
  6. filtrationfiltered
  7. concentrationconcentrated at reduced pressure
  8. dissolutionThe resulting oil was dissolved in tetrahydrofuran (120 mL) and to this solution
  9. additionwas added tetrabutylammonium fluoride (48 mL of a 1.0M solution in tetrahydrofuran) dropwise
  10. waitAfter ten minutes
  11. concentrationthe reaction mixture was concentrated at reduced pressure
  12. customthe resulting oil was chromatographed on silica gel eluting with 97:3 ethyl acetate
  13. custommethanol to give
  14. customwas used without further purification

출처 및 근거

ORD 기록
ord-ea383873bab343559b4d2f08c64524a2
출처 데이터셋
uspto-grants-1998_02
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US05717100

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트