홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Methanol → 4-Methyl-2,3,5,6-tetrafluorobenzyl alcohol

HRID 971184
인쇄

반응식

HRID 971184 반응식
CO.[F:3][C:4]1[C:11]([F:12])=[C:10]([CH2:13]Br)[C:9]([F:15])=[C:8]([F:16])[C:5]=1[CH2:6][OH:7]>[Pd].O>[F:3][C:4]1[C:11]([F:12])=[C:10]([CH3:13])[C:9]([F:15])=[C:8]([F:16])[C:5]=1[CH2:6][OH:7]
참가 물질실험 절차후처리출처 및 근거반응 노트

참가 물질

5

반응물 2

HCID 887MethanolHCID 11265752(4-(Bromomethyl)-2,3,5,6-tetrafluorophenyl)methanol

생성물 1

HCID 27342094-Methyl-2,3,5,6-tetrafluorobenzyl alcohol수율 89.4%

시약·촉매·용매 2

HCID 23938Palladium촉매HCID 962Water용매

실험 절차

The following procedures were carried out in a 1 litre glass autoclave (working volume 350-500 mls) fitted with a dispersion agitator (1000 rpm). H2 gas was fed through a dip-pipe via a Buchi gas controller (Type 6002). The increase/decrease of the temperature is controlled by a Jelabo FP40 external heating/cooling bath. Methanol (362 g, water (6 g, 2,3,5,6-tetrafluoro-4-(bromomethyl)benzyl alcohol (95.1 g 100% wt.), MgO (18.1 g and 5% palladium/carbon catalyst (0.8 g, 100 wt %; Type 58, provided by Johnson Matthey) were charged to the autoclave. The lid was sealed and the autoclave was initially purged with nitrogen to remove residual oxygen (nearly 0), then pressurized to 2.5 bar with hydrogen, and stirred. The pressure was maintained at 2.5 bar by the Buchi controller. The reaction temperature was controlled at 50° C. throughout the reaction by means of the external heating/cooling bath. The reaction was continued until the consumption of hydrogen ceased (typically 60 to 90 minutes). The residual pressure was released and the autoclave purged with nitrogen. The contents of the autoclave were discharged, followed by a small methanol (30 g wash. The spent catalyst and inorganic salts were removed and recovered by filtration. The filter cake was washed with a small amount of methanol (2×30 g. The filtrates and filter-cake washes were combined. On analysis, the reaction had produced 60.4 g of 2,3,5,6-tetrafluoro-4-methylbenzyl alcohol with a yield of 89.4%.

후처리

  1. customfitted with a dispersion agitator (1000 rpm)
  2. temperatureThe increase/decrease of the temperature
  3. customis controlled by a Jelabo FP40 external heating/cooling bath
  4. customThe lid was sealed
  5. customthe autoclave was initially purged with nitrogen
  6. customto remove residual oxygen (nearly 0),
  7. temperatureThe pressure was maintained at 2.5 bar by the Buchi controller
  8. customThe reaction temperature was controlled at 50° C. throughout the reaction by means of the external heating/cooling bath
  9. customThe reaction was continued until the consumption of hydrogen
  10. customtypically 60 to 90 minutes
  11. customthe autoclave purged with nitrogen
  12. washwash
  13. customThe spent catalyst and inorganic salts were removed
  14. filtrationrecovered by filtration
  15. washThe filter cake was washed with a small amount of methanol (2×30 g
  16. filtrationThe filtrates and filter-cake washes

출처 및 근거

ORD 기록
ord-fa0ca8c33fcd414dafb1468ac0f1e1d2
출처 데이터셋
uspto-grants-2007_12
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US07312366B2

반응 노트

이 페이지에서참가 물질실험 절차후처리출처 및 근거반응 노트