Zurück
HuagongsheHuagongshe Chemie-Druckbericht · Nur für Forschungszwecke
HRID 1478272Erstellt: 25. Oktober 2026

Acetonitrile → Isopropyl 4-(3-(2-ethoxypyridin-3-yl)pyrazolo[1,5-a]pyrimidin-5-yl)piperazine-1-carboxylate

https://huagongshe.com/reaction/1478272

Reaktionsgleichung

Beteiligte Stoffe

RolleNameHCIDEinwaage
EduktAcetonitrileHCID 6342—
EduktPotassium CarbonateHCID 11430—
Edukt2-Ethoxypyridine-3-boronic acidHCID 11309733—
EduktIsopropyl 4-(3-bromopyrazolo[1,5-a]pyrimidin-5-yl)piperazine-1-carboxylateHCID 86697433—
LösungsmittelWaterHCID 962—
LösungsmittelEthyl AcetateHCID 8857—
ProduktIsopropyl 4-(3-(2-ethoxypyridin-3-yl)pyrazolo[1,5-a]pyrimidin-5-yl)piperazine-1-carboxylateHCID 8980843868,1%

Reaktionsbedingungen

Temperatur85 °C

Reaktionsschritte

To a 1 liter round bottom flask was added 15.00 g (40.76 mmol) of isopropyl 4-(3-bromopyrazolo[1,5-a]pyrimidin-5-yl)piperazine-1-carboxylate, 8.85 g (52.99 mmol) of (2-ethoxypyridin-3-yl)boronic acid, 14.06 g (101.90 mmol) of K2CO3, 1.41 g (1.22 mmol) of P(PPh3)4, and a stirring rod. After adding all the solids, 200 ml of MeCN was added, followed by the addition of 100 mL of water. The reaction flask was plunged into an oil bath pre-heated to 85° C., and stirred vigorously. This reaction was setup to reflux. After stirring at 85° C. for about 16 hr, it was allowed to cool to RT and diluted with 200 mL of EtOAc. The organic layer was separated, and the aqueous layer was extracted twice with 80 mL portions of EtOAc. The combined organic layers was washed with brine, dried over MgSO4, and concentrated. A small volume of DCM was used to dissolve the crude mixture, and then loaded directly onto a 750 g silica gel column for separation on the ISCO-XL. A gradient of 50% EtOAc/hex to 100% EtOAc was run for the first 35 minutes. The desired product did not elute, only some impurities eluted. However, about 10 minutes into running with 100% EtOAc, the desbromo side product starts eluting together with the desired product. Even though the desbromo compound is spread through all the fractions containing the desired product, the percentage of the desbromo compound seem to decrease with time. Therefore, the initial fractions containing the highest percentages of the desbromo were discarded, and the remaining fractions were concentrated to obtain 13.46 g of about 86% purity at 254 nm. (with about 14% desbromo compound). This material was recrystallized twice, using IPAC and heptanes, to obtain 11.4 g (68%) of the desired product. 1H NMR (400 MHz, CHLOROFORM-d) δ ppm 1.30 (d, J=6.32 Hz, 6 H) 1.53 (t, J=7.07 Hz, 3 H) 3.59-3.70 (m, 4H) 3.70-3.81 (m, 4 H) 4.53 (q, J=7.07 Hz, 2 H) 5.00 (dt, J=12.44, 6.28 Hz, 1 H) 6.38 (d, J=7.83 Hz, 1 H) 6.98 (dd, J=7.45, 4.93 Hz, 1 H) 8.01 (dd, J=4.93, 1.89 Hz, 1H) 8.37 (d, J=7.83 Hz, 1 H) 8.70 (s, 1 H) 8.76 (dd, J=7.45, 1.89 Hz, 1 H). LRMS (ESI) m/e 411 [(M+H)+, calcd for C21H26N6O3 410].

Herkunft & Nachweise

DOI10.6084/m9.figshare.5104873.v1
PatentnummerUS09403832B2
Quelldatensatzuspto-grants-2016_08
ORD IDord-c25bf40755ae401d9e5cb1dc73501ede
Quellennotizuspto-grants-2016_08