反应详情

All oligonucleotides are synthesized on an AKTAoligopilot synthesizer. Commercially available controlled pore glass solid support (dT-CPG, 500 Å, Prime Synthesis) and RNA phosphoramidites with standard protecting groups, 5′-β-dimethoxytrityl N6-benzoyl-2′-t-butyldimethylsilyl-adenosine-3′-O—N,N′-diisopropyl-2-cyanoethylphosphoramidite, 5′-O-dimethoxytrityl-N4-acetyl-2′-t-butyldimethylsilyl-cytidine-3′-O—N,N′-diisopropyl-2-cyanoethylphosphoramidite, 5′-O-dimethoxytrityl-N2-isobutryl-2′-t-butyldimethylsilyl-guanosine-3′-O—N,N′-diisopropyl-2-cyanoethylphosphoramidite, and 5′-O-dimethoxytrityl-2′-t-butyldimethylsilyl-uridine-3′-O—N,N′-diisopropyl-2-cyanoethylphosphoramidite (Pierce Nucleic Acids Technologies) were used for the oligonucleotide synthesis. The 2′-F phosphoramidites, 5′-O-dimethoxytrityl-N4-acetyl-2′-fluoro-cytidine-3′-O—N,N′-diisopropyl-2-cyanoethyl-phosphoramidite and 5′-O-dimethoxytrityl-2′-fluoro-uridine-3′-O—N,N′-diisopropyl-2-cyanoethyl-phosphoramidite are purchased from (Promega). All phosphoramidites are used at a concentration of 0.2M in acetonitrile (CH3CN) except for guanosine which is used at 0.2M concentration in 10% THF/ANC (v/v). Coupling/recycling time of 16 minutes is used. The activator is 5-ethyl thiotetrazole (0.75M, American International Chemicals); for the PO-oxidation iodine/water/pyridine is used and for the PS-oxidation PADS (2%) in 2,6-lutidine/ACN (1:1 v/v) is used. 3′-ligand conjugated strands are synthesized using solid support containing the corresponding ligand. For example, the introduction of cholesterol unit in the sequence is performed from a hydroxyprolinol-cholesterol phosphoramidite. Cholesterol is tethered to trans-4-hydroxyprolinol via a 6-aminohexanoate linkage to obtain a hydroxyprolinol-cholesterol moiety. 5′-end Cy-3 and Cy-5.5 (fluorophore) labeled siRNAs are synthesized from the corresponding Quasar-570 (Cy-3) phosphoramidite are purchased from Biosearch Technologies. Conjugation of ligands to 5′-end and or internal position is achieved by using appropriately protected ligand-phosphoramidite building block. An extended 15 min coupling of 0.1 M solution of phosphoramidite in anhydrous CH3CN in the presence of 5-(ethylthio)-1H-tetrazole activator to a solid-support-bound oligonucleotide. Oxidation of the internucleotide phosphite to the phosphate is carried out using standard iodine-water as reported (1) or by treatment with tert-butyl hydroperoxide/acetonitrile/water (10:87:3) with 10 min oxidation wait time conjugated oligonucleotide. Phosphorothioate is introduced by the oxidation of phosphite to phosphorothioate by using a sulfur transfer reagent such as DDTT (purchased from AM Chemicals), PADS and or Beaucage reagent. The cholesterol phosphoramidite is synthesized in house and used at a concentration of 0.1 M in dichloromethane. Coupling time for the cholesterol phosphoramidite is 16 minutes. Deprotection I (Nucleobase Deprotection) After completion of synthesis, the support is transferred to a 100 mL glass bottle (VWR). The oligonucleotide is cleaved from the support with simultaneous deprotection of base and phosphate groups with 80 mL of a mixture of ethanolic ammonia [ammonia:ethanol (3:1)] for 6.5 h at 55° C. The bottle is cooled briefly on ice and then the ethanolic ammonia mixture is filtered into a new 250-mL bottle. The CPG is washed with 2×40 mL portions of ethanol/water (1:1 v/v). The volume of the mixture is then reduced to ˜30 mL by roto-vap. The mixture is then frozen on dry ice and dried under vacuum on a speed vac. Deprotection II (Removal of 2′-TBDMS Group)

1. concentrationis used at 0.2M concentration in 10% THF/ANC (v/v)
2. customCoupling/recycling time of 16 minutes
3. customare synthesized
4. additioncontaining the corresponding ligand