StartseiteMCPWorkbenchSkills
StartseiteWorkbenchBenachrichtigungenMein Bereich
llms.txt · MCP-AnleitungDatenschutz · Nutzungsbedingungen · Supportv1.8.3
  1. Startseite
  2. /Reaktion

Nitrogen → 2-Pent-4-ynyl-cyclopropanol

HRID 1518899
Drucken

Reaktionsgleichung

Reaktionsgleichung von HRID 1518899
N#N.[CH2:3]1[CH2:7][O:6][CH2:5][CH2:4]1.[CH2:8]([Li])[CH2:9][CH2:10][CH2:11]CC.C1(O)CC1>CN1C(=O)N(C)CCC1>[CH2:5]([CH:4]1[CH2:3][CH:7]1[OH:6])[CH2:11][CH2:10][C:9]#[CH:8]
KomponentenReaktionsbedingungenVersuchsvorschriftAufarbeitungQuellen und NachweiseNotizen zur Reaktion

Komponenten

6

Edukt 4

HCID 947Nitrogen2×HCID 8028TetrahydrofuranHCID 123361CyclopropanolHCID 178506865HCID 178506865, Verbindung

Produkt 1

HCID 781002602-Pent-4-ynyl-cyclopropanolAusbeute 98 %

Reagenzien, Katalysatoren, Lösungsmittel 1

HCID 81646
2(1H)-Pyrimidinone, tetrahydro-1,3-dimethyl-
Lösungsmittel

Reaktionsbedingungen

Temperatur
0 °C

Versuchsvorschrift

To a 2-neck 15-mL round bottomed flask equipped with a temperature probe, N2 inlet, and septum was added 1 g of 4 (7.28 mmol, 1.0 equiv) and 3.0 mL THF. The solution was cooled to an internal temperature of 0° C. with an ice bath. To this solution was added 2.95 mL of 33 wt % n-Hexyllithium (7.28 mmol, 1.0 equiv) slowly via syringe pump over 1 hour. Internal temperature rose to 6.8° C. and solution became yellow. In a separate 3-neck 100-mL round bottomed flask equipped with a temperature probe, N2 inlet, and septum 0.82 g of lithium acetylide-ethylenediamine complex (8.01 mmol, 1.1 equiv) was slurried in 5.0 mL of DMPU at room temperature. To this room temperature slurry, the cold solution of the deprotonated cyclopropanol was transferred via cannula over 5 min. After the addition, the brown mixture was heated to an internal temperature of 52° C. with a heating mantle for 3 hours or until greater than 98% conversion was observed by GC. The brown mixture was cooled with an ice bath to 3° C. and then the ice bath was removed to prevent freezing. To this was slowly added 17.5 mL of 0.5 N HCl and an ice bath was applied to maintain an internal temperature below 21° C. The mixture was then diluted with 10 mL MTBE and 5 mL of water before transfer to a separatory funnel and removal of the aqueous layer. The aqueous layer was extracted once with 15 mL MTBE and then the combined organic layers were washed with 20 mL water followed by 20 mL brine. The organic layer was then concentrated in vacuo to afford 1.27 g of rac-5 as a yellow oil (72 wt %, 98% yield). 1H NMR (400 MHz, CDCl3) δ 3.24 (dt, 1H, J=2.6, 5.3 Hz), 2.25 (dt, 2H, J=2.6, 7.6 Hz), 1.96 (t, 1H, J=2.6 Hz), 1.92 (s, 1H, OH), 1.64 (pent, 2H, J=7.3 Hz), 1.38 (sext, 1H, J=6.9 Hz), 1.24 (sext, 1H, J=6.9 Hz), 0.93 (m, 1H), 0.72 (m, 1H), 0.35 (q, 1H, J=6.0 Hz); 13C NMR (100 MHz, CDCl3) δ 84.49, 68.37, 52.45, 30.50, 27.74, 20.17, 18.01, 14.25; GC: HP1 (30 m×0.32 mm; 0.25 μm), 25 psi, 200° C. front inlet. 5 min @ 50° C., ramp 25° C./min to 250° C. then hold for 4 min, tr(4)=7.15 min, tr(rac-5)=6.72 min.

Aufarbeitung

  1. customrose to 6.8° C.
  2. additionAfter the addition
  3. temperaturethe brown mixture was heated to an internal temperature of 52° C. with a heating mantle for 3 hours or until greater than 98% conversion
  4. temperatureThe brown mixture was cooled with an ice bath to 3° C.
  5. customthe ice bath was removed
  6. temperatureto maintain an internal temperature below 21° C
  7. additionThe mixture was then diluted with 10 mL MTBE and 5 mL of water before transfer to a separatory funnel
  8. customremoval of the aqueous layer
  9. extractionThe aqueous layer was extracted once with 15 mL MTBE
  10. washthe combined organic layers were washed with 20 mL water
  11. concentrationThe organic layer was then concentrated in vacuo
  12. customto afford 1.27 g of rac-5 as a yellow oil (72 wt %, 98% yield)
  13. customHP1 (30 m×0.32 mm; 0.25 μm), 25 psi, 200° C. front inlet
  14. custom5 min
  15. custom@ 50° C.
  16. customtr(4)=7.15 min, tr(rac-5)=6.72 min.

Quellen und Nachweise

ORD-Eintrag
ord-a06507434067440daf3ca54aabf195e3
Quelldatensatz
uspto-grants-2015_07
DOI
10.6084/m9.figshare.5104873.v1
Patentnummer
US09073825B2

Notizen zur Reaktion

Auf dieser SeiteKomponentenReaktionsbedingungenVersuchsvorschriftAufarbeitungQuellen und NachweiseNotizen zur Reaktion