StartseiteMCPWorkbenchSkills
StartseiteWorkbenchBenachrichtigungenMein Bereich
llms.txt · MCP-AnleitungDatenschutz · Nutzungsbedingungen · Supportv1.8.3
  1. Startseite
  2. /Reaktion

Ethanol → water TEOS

HRID 2073699
Drucken

Reaktionsgleichung

Reaktionsgleichung von HRID 2073699
[CH2:1]([O:3][Si:4]([O:11][CH2:12][CH3:13])([O:8][CH2:9][CH3:10])[O:5][CH2:6][CH3:7])[CH3:2].C(O)C.[N+]([O-])(O)=O>O>[OH2:3].[CH2:6]([O:5][Si:4]([O:8][CH2:9][CH3:10])([O:3][CH2:1][CH3:2])[O:11][CH2:12][CH3:13])[CH3:7]
KomponentenVersuchsvorschriftAufarbeitungQuellen und NachweiseNotizen zur Reaktion

Komponenten

5

Edukt 3

HCID 702EthanolHCID 944Nitric AcidHCID 6517Tetraethoxysilane

Produkt 1

HCID 87705869water TEOS

Reagenzien, Katalysatoren, Lösungsmittel 1

HCID 962WaterLösungsmittel

Versuchsvorschrift

A sol is formed by mixing 520 grams of tetraethoxysilane (TEOS) with 235 grams of reagent grade ethanol at 60° to 65° C. A solution of 1.6 grams of nitric acid in 78.5 grams of deionized water is added to the sol in four increments at about 15 minute intervals, producing a sol with a water/TEOS molar ratio of 1.75. The tetraethoxysilane is allowed to hydrolyze for one hour at 60° to 65° C. The sol is then allowed to cool to ambient temperature. The sol is vacuum distilled at 50° C. in a rotary evaporator. After distillation, the sol is rediluted with ethanol to a solids content of 53 percent. The sol is then aged until it reaches the desired spinning viscosity. The sol is placed in a sealed reservoir pressurized with 30 pounds per square inch of helium. The pressure forces the sol into a gear driven pump which delivers the sol to a spinnerette. The sol is continuously extruded through a 4-hole spinnerette with hole diameters of 280 microns. The continuously extruded fibers are drawn vertically downward through a spin tube about 9 feet (about 2.74 meters) long containing an atmosphere comprising ammonia in air. The concentration of NH3 is about 19,000 parts per million. After brief exposure to ammonia, the continuous fibers are non-tacky. The continuous non-tacky fibers are brought together by a guide to form a single compact strand. The continuous strand is then gathered on a take-up winder. After the strand is collected, it is fired to form the final silica fiber product. In this example, the fibers are placed in an oven programmed to raise the temperature 15° C. per minute. During this heating cycle, 200 cubic centimeters per minute of oxygen is introduced into the oven until the temperature reaches 500° C. The temperature is further raised to 850° C., at which the fibers are held for 5 minutes.

Aufarbeitung

  1. customA sol is formed

Quellen und Nachweise

ORD-Eintrag
ord-3d4995c2a0b8487fbfa7a422835a1328
Quelldatensatz
uspto-grants-1990_04
DOI
10.6084/m9.figshare.5104873.v1
Patentnummer
US04919871

Notizen zur Reaktion

Auf dieser SeiteKomponentenVersuchsvorschriftAufarbeitungQuellen und NachweiseNotizen zur Reaktion