HomeMCPWorkbenchSkills
HomeWorkbenchNotificationsMe
llms.txt · MCP GuidePrivacy Policy · Terms of Service · Supportv1.8.3
  1. Home
  2. /Reaction

Water → Butyl prop-2-enoate--methyl 2-methylprop-2-enoate (1/1)

HRID 748553
Print

Reaction equation

HRID 748553 reaction equation
O.[C:2]([O:6][CH2:7][CH2:8][CH2:9][CH3:10])(=[O:5])[CH:3]=[CH2:4].[C:11](=O)([O-])[O-].[Ca+2]>C(OC)(=O)C(C)=C.N(C(C#N)(C)CCC(O)=O)=NC(C#N)(C)CCC(O)=O>[C:2]([O:6][CH3:7])(=[O:5])[C:3]([CH3:11])=[CH2:4].[C:2]([O:6][CH2:7][CH2:8][CH2:9][CH3:10])(=[O:5])[CH:3]=[CH2:4]
ParticipantsProcedureWorkupSources & evidenceReaction notes

Participants

6

Reactant 3

HCID 962WaterHCID 8846Butyl AcrylateHCID 10112Calcium Carbonate

Product 1

HCID 62802Butyl prop-2-enoate--methyl 2-methylprop-2-enoate (1/1)

Reagents, catalysts & solvents 2

HCID 929384,4-Azobis(4-cyanovaleric acid)Catalyst
HCID 6658
Methyl Methacrylate
Solvent
2×

Procedure

(wherein Me represents methyl and Ph represents phenyl), was dissolved in 3.0 g of methyl methacrylate as a monomer, and the solution was added into the reactor. After 20 minutes, as a polymerization initiator, 555 mg of 4,4′-azobis(4-cyanovaleric acid) together with 12 g of distilled water was added into the reactor. Stirring was performed at 80° C. for 20 minutes, and then 52.0 g of methyl methacrylate was dripped from the dropping funnel for over 90 minutes. After 30 minutes, 61.0 g of n-butyl acrylate as a monomer was dripped from the dropping funnel for over 1 hour. Stirring was performed at 80° C. for 6 hours, and the emulsion was salted out with calcium carbonate, followed by washing with distilled water. Thereby, 94.1 g of a methyl methacrylate-n-butyl acrylate diblock copolymer was produced. GPC confirmed that in the polymer, Mw=59,800, Mn=44,400, and Mw/Mn=1.35. 1H NMR analysis confirmed that the weight ratio of the poly(methyl methacrylate) portion to the poly(n-butyl acrylate) portion was 48:52, and that thiocarbonylthio groups were introduced at the poly(n-butyl acrylate) ends with an introduction rate of 84%.

Workup

  1. additionthe solution was added into the reactor
  2. waitwas performed at 80° C. for 20 minutes
  3. customwas dripped from the dropping funnel for over 90 minutes
  4. waitAfter 30 minutes
  5. customwas dripped from the dropping funnel for over 1 hour
  6. stirringStirring
  7. waitwas performed at 80° C. for 6 hours
  8. washby washing with distilled water

Sources & evidence

ORD record
ord-79d2beca13714bea92273351fdd836a0
Source dataset
uspto-grants-2008_07
DOI
10.6084/m9.figshare.5104873.v1
Patent number
US07399801B2

Reaction notes

On this pageParticipantsProcedureWorkupSources & evidenceReaction notes