ホームMCPワークベンチSkills
ホームワークベンチ通知マイページ
llms.txt · MCPガイドプライバシーポリシー · 利用規約 · サポートv1.8.3
  1. ホーム
  2. /反応

Diisopropylamine → alpha-Amino-N-(2-hydroxy-1-methyl-2-phenylethyl)-N-methyl-1, 3-dioxolane-2-pentanamide

HRID 2269696
印刷

反応式

HRID 2269696 の反応式
C(NC(C)C)(C)C.[CH2:8]([Li])[CH2:9][CH2:10][CH3:11].[OH2:13].[OH:14][CH:15]([C:24]1[CH:29]=[CH:28][CH:27]=[CH:26][CH:25]=1)[CH:16]([N:18]([CH3:23])[C:19](=[O:22])[CH2:20][NH2:21])[CH3:17].[Cl-].[Li+].[O:32]1[CH2:36][CH2:35]CC1>>[NH2:21][CH:20]([CH2:11][CH2:10][CH2:9][CH:8]1[O:32][CH2:36][CH2:35][O:13]1)[C:19]([N:18]([CH:16]([CH3:17])[CH:15]([OH:14])[C:24]1[CH:29]=[CH:28][CH:27]=[CH:26][CH:25]=1)[CH3:23])=[O:22]
参加物反応条件実験手順後処理出典と根拠反応ノート

参加物

6

反応物 5

HCID 7912DiisopropylamineHCID 8028Tetrahydrofuran2 回HCID 433294Lithium ChlorideHCID 70213195N-(2-hydroxy-1-methyl-2-phenylethyl)-N-methyl-alpha-aminoacetamide monohydrateHCID 178418339Butyllithium

生成物 1

HCID 20665105alpha-Amino-N-(2-hydroxy-1-methyl-2-phenylethyl)-N-methyl-1, 3-dioxolane-2-pentanamide

反応条件

温度
-5 °C

実験手順

A 0.5-1, 5-necked, round-bottom flask, equipped with an overhead stirrer, thermocouple, addition funnel and a nitrogen inlet/outlet was charged with diisopropylamine (45.52 g) and tetrahydrofuran (175 ml). After cooling to −5° C., a 2.49M solution of freshly titrated n-butyllithium in hexanes (176.7 ml) was added while maintaining the temperature at −5° C. to 21° C. This mixture was allowed to stir at 21° C. for 45 minutes and was then cooled to −5° C. This cooled solution was added to a tetrahydrofuran (700 ml, −5° C. ) slurry of [R-(R*,R*)]-N-(2-hydroxy-1-methyl-2-phenylethyl)-N-methyl-α-aminoacetamide monohydrate (50 g) and lithium chloride (57.21 g, was dried in vacuo at 130° C. for 6 hours and then at 100° C. for 18 hours prior to use) maintaining the temperature in the range −7° to 7° C. After the addition was complete, the mixture was stirred for an additional hour at 0° to 3° C. 2-(3-Iodopropyl)-1,3-dioxolane (51.72 g) was added to the reaction mixture as a tetrahydrofuran (50 ml) solution over 15 minutes with agitation. The reaction was stirred for 3 hours at 0° C. until it was determined to be complete (HPLC analysis). The reaction was quenched by the addition of water (450 ml) and the tetrahydrofuran/hexane phase was separated from the lower aqueous phase and set aside. The pH of the aqueous phase was adjusted from about 11 to about 8 by the addition of concentrated hydrochloric acid (10 ml) and then extracted with methylene chloride (2×250 ml). The methylene chloride phases were combined and concentrated in vacuo (bath temperature less than or equal to 40° C.) to afford [αS-[αR*(1S*,2S*)]]-α-amino-N-(2-hydroxy-1-methyl-2-phenylethyl)-N-methyl-1,3-dioxolane-2-pentanamide as an oil (60 g). The oil was dissolved in water (300 ml) with heating and was refluxed for 12 hours until it was judged to be complete (HPLC analysis). After cooling, the reaction mixture was extracted with methylene chloride (2×250 ml) and the rich aqueous phase was concentrated in vacuo to afford the crude product as a yellow solid. The yellow solid was recrystallized from aqueous ethanol (water 75 ml, absolute ethanol 500 ml) and dried in vacuo to give 18.8 g of desired product as a white crystalline solid.

後処理

  1. customA 0.5-1, 5-necked, round-bottom flask, equipped with an overhead stirrer
  2. additionthermocouple, addition funnel and a nitrogen inlet/outlet
  3. temperaturewhile maintaining the temperature at −5° C. to 21° C
  4. temperaturewas then cooled to −5° C
  5. customwas dried in vacuo at 130° C. for 6 hours
  6. waitat 100° C. for 18 hours
  7. temperaturemaintaining the temperature in the range −7° to 7° C
  8. additionAfter the addition
  9. stirringthe mixture was stirred for an additional hour at 0° to 3° C
  10. addition2-(3-Iodopropyl)-1,3-dioxolane (51.72 g) was added to the reaction mixture as a tetrahydrofuran (50 ml) solution over 15 minutes with agitation
  11. stirringThe reaction was stirred for 3 hours at 0° C. until it
  12. customThe reaction was quenched by the addition of water (450 ml)
  13. customthe tetrahydrofuran/hexane phase was separated from the lower aqueous phase
  14. additionThe pH of the aqueous phase was adjusted from about 11 to about 8 by the addition of concentrated hydrochloric acid (10 ml)
  15. extractionextracted with methylene chloride (2×250 ml)
  16. concentrationconcentrated in vacuo (bath temperature less than or equal to 40° C.)

出典と根拠

ORDレコード
ord-36e12b0744f24e968fb8862c798633e4
出典データセット
uspto-grants-2001_12
DOI
10.6084/m9.figshare.5104873.v1
特許番号
US06329542B1

反応ノート

このページの内容参加物反応条件実験手順後処理出典と根拠反応ノート