tert-부틸알코올

Fire Extinguishing Agents Not to Be Used: Water may be ineffective on fire

Use water spray, alcohol-resistant foam, powder, carbon dioxide. In case of fire: keep drums, etc., cool by spraying with water.

Fresh air, rest. Refer for medical attention.

Remove contaminated clothes. Rinse skin with plenty of water or shower.

First rinse with plenty of water for several minutes (remove contact lenses if easily possible), then refer for medical attention.

Rinse mouth. Give one or two glasses of water to drink. Do NOT induce vomiting. Refer for medical attention .

EYES: First check the victim for contact lenses and remove if present. Flush victim's eyes with water or normal saline solution for 20 to 30 minutes while simultaneously calling a hospital or poison control center. Do not put any ointments, oils, or medication in the victim's eyes without specific instructions from a physician. IMMEDIATELY transport the victim after flushing eyes to a hospital even if no symptoms (such as redness or irritation) develop.

(General first aid procedures)

Flash back possible over considerable distance.

Suitable extinguishing media: Use water spray, alcohol-resistant foam, dry chemical or carbon dioxide.

Wear self contained breathing apparatus for fire fighting if necessary.

In case of fire: Evacuate area. Fight fire remotely due to the risk of explosion.Use water spray to cool unopened containers.

Flammable in the presence of a source of ignition when the temperature is above the flash point. Keep away from heat/sparks/open flame/hot surface. No smoking.

Personal precautions: Use personal protective equipment. Avoid breathing vapors, mist or gas. Ensure adequate ventilation. Remove all sources of ignition. Evacuate personnel to safe areas. Beware of vapors accumulating to form explosive concentrations. Vapors can accumulate in low areas. Environmental precautions: Prevent further leakage or spillage if safe to do so. Do not let product enter drains. Methods and materials for containment and cleaning up: Contain spillage, and then collect with an electrically protected vacuum cleaner or by wet-brushing and place in container for disposal according to local regulations.

SMALL SPILLS AND LEAKAGE: If you spill this chemical, FIRST REMOVE ALL SOURCES OF IGNITION. Then, use absorbent paper to pick up all liquid spill material. Seal the absorbent paper, as well as any of your clothing which may be contaminated, in a vapor-tight plastic bag for eventual disposal. Wash any surfaces you may have contaminated with a soap and water solution. Do not reenter the contaminated area until the Safety Officer (or other responsible person) has verified that the area has been properly cleaned.

SRP: Wastewater from contaminant suppression, cleaning of protective clothing/equipment, or contaminated sites should be contained and evaluated for subject chemical or decomposition product concentrations. Concentrations shall be lower than applicable environmental discharge or disposal criteria. Alternatively, pretreatment and/or discharge to a permitted wastewater treatment facility is acceptable only after review by the governing authority and assurance that "pass through" violations will not occur. Due consideration shall be given to remediation worker exposure (inhalation, dermal and ingestion) as well as fate during treatment, transfer and disposal. If it is not practicable to manage the chemical in this fashion, it must be evaluated in accordance with EPA 40 CFR Part 261, specifically Subpart B, in order to determine the appropriate local, state and federal requirements for disposal.

1. Absorbing in vermiculite, dry sand, earth or similar material & disposing in secured sanitary landfill. 2. Atomizing in suitable combustion chamber.

/t-Butyl alcohol/ is a waste chemical stream constituent which may be subjected to ultimate disposal by controlled incineration. /Butanols, from table/

Incineration & landfill: Incinerate waste by atomizing into a suitable combustion chamber. Bury absorbed waste in an approved landfill.

Remove all ignition sources. Evacuate danger area! Consult an expert! Personal protection: self-contained breathing apparatus. Ventilation. Collect leaking liquid in sealable containers. Absorb remaining liquid in sand or inert absorbent. Then store and dispose of according to local regulations. Wash away remainder with plenty of water.

t-Butyl alcohol was identified, not quantified, in mother's milk(1,2). Results of blood analysis were reported for t-butyl alcohol from the 15 participants in the third National Health and Nutrition Examination Survey (NHANES III) and 18 Fairbanks, AK workers exposed to gasoline fumes and/or combustion products of gasoline(3). t-Butyl alcohol blood levels in the NHANES III study were 0.4-6.0 ug/L with a mean of 1.9 ug/L; Fairbanks post-shift workers blood levels were 1.6-76.5 ug/L with a mean of 23.1 ug/L(3). Twelve road-tanker truck drivers that worked various depot routes in Finland had t-butyl alcohol levels in urine of 173 to 1293 nmol/L (mean 461 nmol/L), immediately after the shift; 16 hours later the mean concentration was 322 nmol/L(4).

t-Butyl alcohol levels in blood and urine samples from tank-lorry drivers from Helsinki, Finland were reported(1).[Table#88]

Tertiary butyl alcohol and trichloroacetic acid are known to be contaminants in drinking water. In order to evaluate the interactive toxicity of t-butyl alcohol with trichloroacetic acid, young male Wistar rats were dosed through water at a dose level of t-butyl alcohol (TBA)-0.5% (v/v), trichloroacetic acid (TCA)-25 ppm and a combined dose of TBA + TCA (0.5% v/v TBA-25 ppm TCA) for a period of 10 weeks ad libitum and were maintained on normal diet. The control animals received plain water and normal diet. The liver and kidney histology was undertaken to see whether subtoxic administration of TBA and TCA individually as well as combined administration for a period of 10 weeks would bring about any histological alterations. It was observed that TBA, TCA and TBA + TCA caused histological alterations in the liver such as centrilobular necrosis, vacuolation in hepatocytes and loss of hepatic architecture. TBA and TBA + TCA caused periportal proliferation and lymphocytic infiltration. Hypertrophy of hepatocytes in the periportal area was a characteristic feature in the liver of TCA treated rats. Moreover, in the histology of the kidney, in the three treated groups, degeneration of renal tubules, with syncitial arrangements of the nucleus of renal tubular epithelial cells was evident. In addition to this, degeneration of the basement membrane of the Bowmans capsule, diffused glomeruli and vacuolation of glomeruli was also evident in the three treated rat kidneys. Renal tubular proliferation in certain areas was also evident in certain areas of the kidney in TCA treated rats. The results indicate that, TBA and TCA do bring about alterations in histology of liver and kidney, but on combined administration, do not show enhanced toxicity in the form of increased hepatic and renal injury.

Urinary

Eyes, skin, respiratory system, central nervous system

LD100; Species: Semolitus atromaculatus (creek chub) 6000 mg/L for 24 hr in Detroit river water /Conditions of bioassay not specified/

LC50; Species: Poecilia reticulata (guppy) 3550 ppm for 7 days /Conditions of bioassay not specified/

LC50; Species: Xenopus laevis (African Clawed Frog) age 3-4 wk; Conditions: freshwater, static, 20 °C; Concentration: 2450000 ug/L for 48 hr /formulated product/

EC50; Species: Daphnia magna (Water Flea); Conditions: freshwater, static; Effect: equilibrium; Concentration: 5050000 ug/L for 24 hr /formulated product/

For more Ecotoxicity Values (Complete) data for T-BUTYL ALCOHOL (6 total), please visit the HSDB record page.

TERRESTRIAL FATE: Based on a classification scheme(1), a Koc value of 37(2-3), indicates that t-butyl alcohol is expected to have very high mobility in soil(SRC). Volatilization of t-butyl alcohol from moist soil surfaces is expected to be an important fate process(SRC) given a Henry's Law constant of 9.05X10-6 atm-cu m/mole(4). t-Butyl alcohol is expected to volatilize from dry soil surfaces(SRC) based upon a vapor pressure of 40.7 mm Hg at 25 °C(5). The half-life of t-butyl alcohol under anoxic conditions in a non-amended soil was about 200 days, but the half-lives in the same soil amended with nitrate and sulfate nutrients were 100 and 50 days, respectively(6). Biodegradation of t-butyl alcohol in unamended soils collected at different depths had rates of <0.01 to 0.15 mg/L/day/gram dry soil(7).

Degradation rates have been reported to be 4.01X10-8, 4.46X10-8 and 3.26X10-7/s for t-butyl alcohol(1). Primary persistence in soil, water and air are reported as 148, 160 and 64.6 days, respectively. Secondary persistence in soil, water and air are reported as 134, 156 and 123 days, respectively. Joint persistence with its parent compound methyl-t-butyl ether in soil, water and air are reported as 87.9, 105 and 81.5 days, respectively(1).

AQUATIC FATE: Based on a classification scheme(1), a reported Koc value of 37(2-3), indicates that t-butyl alcohol is not expected to adsorb to suspended solids and sediment(SRC). Volatilization from water surfaces is expected(4) based upon a Henry's Law constant of 9.05X10-6 atm-cu m/mole(5). Using this Henry's Law constant and an estimation method(4), volatilization half-lives for a model river and model lake are 3.6 and 29 days, respectively(SRC). According to a classification scheme(6), a BCF of <5 in carp(7), suggests for bioconcentration in aquatic organisms is low(SRC). t-Butyl alcohol is not expected to undergo hydrolysis in the environment due to the lack of functional groups that hydrolyze under environmental conditions(4). The biodegradation half-life of t-butyl alcohol was reported to range from about 28 to 180 days in aerobic water and 100 to 500 days in anaerobic water(8).

ATMOSPHERIC FATE: According to a model of gas/particle partitioning of semivolatile organic compounds in the atmosphere(1), t-butyl alcohol, which has a vapor pressure of 40.7 mm Hg at 25 °C(2), is expected to exist solely as a vapor in the ambient atmosphere. Vapor-phase t-butyl alcohol is degraded in the atmosphere by reaction with photochemically-produced hydroxyl radicals(SRC); the half-life for this reaction in air is estimated to be 14 days(SRC), calculated from its rate constant of 1.12X10-12 cu cm/molecule-sec at 25 °C(3). t-Butyl alcohol does not contain chromophores that absorb at wavelengths >290 nm(4) and, therefore, is not expected to be susceptible to direct photolysis by sunlight(SRC).

The substance can be absorbed into the body by inhalation of its vapour and by ingestion.

inhalation, ingestion, skin and/or eye contact

Dizziness. Drowsiness. Nausea. Headache. Vomiting.

Redness.

Redness. Pain.

See Inhalation.

irritation eyes, skin, nose, throat; drowsiness, narcosis

Defoaming agents used in coatings. The defoaming agents described in this section may be safely used as components of articles intended for use in producing, manufacturing, packing, processing, preparing, treating, packaging, transporting, or holding food, subject to the provisions of this section. tert-Butyl alcohol is included on this list.

Section 8(a) of TSCA requires manufacturers of this chemical substance to report preliminary assessment information concerned with production, exposure, and use to EPA as cited in the preamble in 51 FR 41329. Effective date: 1/26/94; Reporting date: 3/28/94.

Pursuant to section 8(d) of TSCA, EPA promulgated a model Health and Safety Data Reporting Rule. The section 8(d) model rule requires manufacturers, importers, and processors of listed chemical substances and mixtures to submit to EPA copies and lists of unpublished health and safety studies. t-Butyl alcohol is included on this list. Effective date: 1/26/94; Sunset date: 6/30/98.

As the federal pesticide law FIFRA directs, EPA is conducting a comprehensive review of older pesticides to consider their health and environmental effects and make decisions about their continued use. Under this pesticide reregistration program, EPA examines newer health and safety data for pesticide active ingredients initially registered before November 1, 1984, and determines whether the use of the pesticide does not pose unreasonable risk in accordance to newer saftey standards, such as those described in the Food Quality Protection Act of 1996. Pesticides for which EPA had not issued Registration Standards prior to the effective date of FIFRA '88 were divided into three lists based upon their potential for human exposure and other factors, with List B containing pesticides of greater concern than those on List C, and with List C containing pesticides of greater concern than those on List D. Butyl alcohol is found on List D. Case No: 4003; Pesticide type: insecticide, fungicide, herbicide, antimicrobial; Case Status: RED Approved 3/95; OPP has made a decision that some/all uses of the pesticide are eligible for reregistration, as reflected in a Reregistration Eligibility Decision (RED) document .; Active ingredient (AI): butyl alcohol; AI Status: The active ingredient is no longer contained in any registered products. Thus, we characterize it as "cancelled.".

This action promulgates standards of performance for equipment leaks of Volatile Organic Compounds (VOC) in the Synthetic Organic Chemical Manufacturing Industry (SOCMI). The intended effect of these standards is to require all newly constructed, modified, and reconstructed SOCMI process units to use the best demonstrated system of continuous emission reduction for equipment leaks of VOC, considering costs, non air quality health and environmental impact and energy requirements. t-Butyl alcohol is produced, as an intermediate or a final product, by process units covered under this subpart.

(CA) CALIFORNIA 12 ug/L

(MA) MASSACHUSETTS 120 ug/L

(NH) NEW HAMPSHIRE 40 ug/L

(NJ) NEW JERSEY 100 ug/L

CIR ingredient: t-Butyl Alcohol

Used to manufacture flavors and perfumes; also used as a solvent, alcohol denaturant, and gasoline additive; [ACGIH] Used in lacquers and paint removers; [HSDB]

Painting (Solvents) [Category: Paint]

For t-butyl alcohol (USEPA/OPP Pesticide Code: 001505) there are 0 labels match. /SRP: Not registered for current use in the U.S., but approved pesticide uses may change periodically and so federal, state and local authorities must be consulted for currently approved uses./

The active ingredient is no longer contained in any registered products ... "cancelled.".

The solvent sector is the major field of application. 2-Methyl-2-propanol is also used as an agent for introducing the tert-butyl group into organic compounds (e.g., tert-butylphenol for the preparation of oil-soluble resins and antioxidants, trinitro-tert-butyltoluene as artificial musk) and as a starting material for the preparation of peroxides (polymerization catalysts).

(1972) NEGLIGIBLE

(1984) LESS THAN 3.69X10+8 g

2023: 5,500,000,000 - <7,000,000,000 lb

(1984) Less than 8.52X10+11 g

t-Butyl alcohol is listed as a High Production Volume (HPV) chemical (65FR81686). Chemicals listed as HPV were produced in or imported into the U.S. in >1 million pounds in 1990 and or 1994. The HPV list is based on the 1990 Inventory Update Rule. (IUR ) (40 CFR part 710 subpart B; 51FR21438).

Production volumes for non-confidential chemicals reported under the Inventory Update Rule.[Table#93]

Production volume for non-confidential chemicals reported under the 2006 Inventory Update Rule. Chemical: 2-Propanol, 2-methyl-. Aggregated National Production Volume: 1 billion pounds and greater.

Non-confidential 2012 Chemical Data Reporting (CDR) information on the production and use of chemicals manufactured or imported into the United States. Chemical: 2-Propanol, 2-methyl-. National Production Volume: 4,193,475,865 lb/yr.

... 2-Methyl-2-propanol can be obtained by the acid-catalyzed addition of water to ... 2-methylpropene ... The water adds at the double bond in accordance with the Markovnikov rule. The difference in olefin reactivity can be used for the selective manufacture of ... 2-methyl-2-propanol from technical C4-fractions where the ... alcohol /is/ prepared in turn and isolated.

2-Methyl-2-propanol is formed during the manufacture of propylene oxide from 2-methylpropane in an amount of about 1.2 /ton/ ... per ton of propylene oxide.

2-Methyl-2-propanol is obtained as a byproduct ... /during/ the splitting of methyl tert-butyl ether to highly pure 2-methylpropene or 2-methyl-2-propanol. Similarly, the methyl tert-butyl ether synthesis with slight traces of water in the feedstock (methanol and C4-olefins) produces 2-methyl-2-propanol as a byproduct.

Hydration, in the presence of sulfuric acid, of 1-butene and isobutylene, leads to the production of 2-butanol and tert-butyl alcohol. tert-Butanol is also produced as a by-product from the isobutane oxidation process for manufacture of propylene oxide.

For more Methods of Manufacturing (Complete) data for T-BUTYL ALCOHOL (7 total), please visit the HSDB record page.

2-Methyl-2-propanol is supplied both as a product of at least 99.8 wt% purity and as an azeotropic mixture with 11 to 12 wt% water.

Grade: Technical

Cosmetics product ingredient: Tertiary butyl alcohol (TBA) (t-Butyl alcohol)

Information on 104 consumer products that contain t-Butyl alcohol in the following categories is provided:

Fragrance Ingredients

Cosmetics -> Denaturant; Solvent

All Other Chemical Product and Preparation Manufacturing

2-Propanol, 2-methyl-: ACTIVE