기본 정보
- 표준 SMILES
c1ccc(-c2ccccc2-c2ccccc2)cc1- InChIKey
OIAQMFOKAXHPNH-UHFFFAOYSA-N- 분자식
- C18H14
- 평균 분자량
- 230.3 g/mol
- 단동위원소 질량
- 230.10955045
개요
O-terphenyl appears as colorless or light-yellow solid. mp: 58-59 °C, bp: 337 °C. Density: 1.16 g/cm3. Insoluble in water. Usually shipped as a solid mixture with its isomers m-terphenyl and p-terphenyl that is used as a heat-transfer fluid.
이름 및 식별자
- 우선 이름
- O-Terphenyl
- IUPAC
- 1,2-diphenylbenzene
- 현지명
- o-터페닐
- 영어명
- o-Terphenyl
- 분자식
- C18H14
- 분자량
- 230.3
이름 및 동의어
이름 더 보기
데이터베이스 식별자
- CAS
84-15-1- PubChem CID
- 6766
- DTXSID
DTXSID1049697- ChEMBL
CHEMBL3560258- UNII
- W5675R7KVW
- EC Number
- 201-517-6
- Nikkaji
- J3.534C
물성
구조 계산 물성
- XLogP
- 6
- 극성 표면적
- 0 Ų
- 수소 결합 공여자 수
- 0
- 수소 결합 수용자 수
- 0
- 회전 가능 결합 수
- 2
- 무거운 원자 수
- 18
- 형식 전하
- 0
- 복잡도
- 206
실험 및 물리화학적 성질
Density
1.1 (NIOSH, 2024) - Denser than water; will sink
1.1
Relative density (water = 1): 1.1
1.1
Color/Form
MONOCLINIC PRISMS FROM METHANOL
Colorless or light yellow solid.
Solubility
Insoluble (NIOSH, 2024)
SOL IN ACETONE, BENZENE, METHANOL, CHLOROFORM
Sparingly soluble in lower alcohols and glycols; very soluble in common aromatic solvents.
Water solubility = 1.24 mg/l at 25 °C
Solubility in water: none
Insoluble
Flash Point
325 °F (NIOSH, 2024)
163 °C
325 °F (163 °C) (OPEN CUP)
163 °C o.c.
(oc) 325 °F
Boiling Point
630 °F at 760 mmHg (NIOSH, 2024)
332 °C AT 760 MM HG
332 °C
630 °F
Melting Point
136 °F (NIOSH, 2024)
56.2 °C
Crumbly, wax-like flakes at room temperature and light amber liquids above the melting point /Commercial terphenyl mixtures/
56.2 °C
136 °F
Vapor Density
7.95 (AIR= 1)
Relative vapor density (air = 1): 7.9
Vapor Pressure
0.09 mmHg at 200 °F (NIOSH, 2024)
0.00025 [mmHg]
2.5X10-4 mm Hg at 25 °C, extrapolated from experimentally-derived coefficients
Vapor pressure, Pa at 25 °C: 0.0033
(200 °F): 0.09 mmHg
물리화학적 성질
- 녹는점
- 56 · 56-59 °C (lit.)
- 끓는 점
- 337 °C · 337 °C (lit.)
- 밀도
- 1 · 1,1 g/cm3
- 증기압
- 1 Pa · <1 Pa (25 °C)
- 굴절률
- 1.55 · 1.5500 (estimate)
- 인화점
- 230 °F · >230 °F
- 저장 조건
- 30 °C · Store below +30°C.
- 용해도
- 1.24 mg/L · 1.24mg/L
- 물리적 상태
- 액체
- 색상
- 흰색에서 거의 흰색
- 수용성
- 물에 불용성. 톨루엔의 용해도는 거의 투명합니다. 저급 알코올 및 글리콜에 거의 용해되지 않습니다. 일반적인 방향족 용매에 매우 잘 녹습니다.
- 비열
- 1.19 J/ · Cp(crystal): 1.19 J/(g·K); Cp(liquid): 1.6 J/(g·K), at 25℃
- BRN
- 1908446 · 1908446
- Henry's Law Constant
- 1.6 · 1.6×10-1 mol/(m3Pa) at 25℃, Duchowicz et al. (2020)
- InChI
- 1S/C18H14/c1-3-9-15(10-4-1)17-13-7-8-14-18(17)16-11-5-2-6-12-16/h1-14H
- InChIKey
- OIAQMFOKAXHPNH-UHFFFAOYSA-N
- SMILES
- c1ccc(cc1)-c2ccccc2-c3ccccc3
- EPA
- o-Terphenyl (84-15-1)
화학적 성질
White crystalline
안전 및 규제
GHS 분류
GHS Classification
Warning
H302 (100%): Harmful if swallowed [Warning Acute toxicity, oral]
P261, P264, P264+P265, P270, P271, P273, P280, P301+P317, P302+P352, P304+P340, P305+P351+P338, P319, P321, P330, P332+P317, P337+P317, P362+P364, P391, P403+P233, P405, and P501 (click each P-code to see the statement)
Aggregated GHS information provided per 58 reports by companies from 8 notifications to the ECHA C&L Inventory. Each notification may be associated with multiple companies.
Danger
H302: Harmful if swallowed [Warning Acute toxicity, oral]
유해성 정보
Regulatory Information
Chemical: 1,1':2',1''-Terphenyl
1,1':2',1''-Terphenyl is listed on the EPA's Chemical Data Reporting (CDR) system. Manufacturers and importers of 1,1':2',1''-Terphenyl are required to report information about their production and use of this chemical to the EPA under the Toxic Substances Control Act (TSCA). (40 eCFR Part 711)
1,2-Diphenylbenzene: Does not have an individual approval but may be used under an appropriate group standard
Hazards Summary
o-Terphenyl caused kidney injury in subchronic feeding studies in rats. Workers complained of eye and respiratory irritation after inhaling vapors of heated terphenyls. The TLV Basis for Terphenyls is upper respiratory tract and eye irritation; [ACGIH] A skin, eye, and respiratory tract irritant; [ICSC]
OSHA Standards
Permissible Exposure Limit: Table Z-1 Ceiling value: 1 ppm (9 mg/cu m). /Terphenyls/
Vacated 1989 OSHA PEL Ceiling limit 5 mg/cu m (0.5 ppm) is still enforced in some states. /Terphenyl (o-, m-, p- isomers)/
NFPA Hazard Classification
0 - Materials that, under emergency conditions, would offer no hazard beyond that of ordinary combustible materials.
1 - Materials that must be preheated before ignition can occur. Materials require considerable preheating, under all ambient temperature conditions, before ignition and combustion can occur.
0 - Materials that in themselves are normally stable, even under fire conditions.
안전 및 보호
First Aid Measures
Fresh air, rest. Refer for medical attention.
Remove contaminated clothes. Rinse and then wash skin with water and soap.
First rinse with plenty of water for several minutes (remove contact lenses if easily possible), then refer for medical attention.
Rinse mouth. Give one or two glasses of water to drink. Refer for medical attention .
First Aid
Excerpt from NIOSH Pocket Guide for o-Terphenyl:
(General first aid procedures)
Cleanup Methods
1. Remove all ignition sources. 2. Ventilate area of spill or leak. 3. For small quant, sweep onto paper or other suitable material, place in an appropriate container and burn in a safe place (such as a fume hood). Large quant may be reclaimed; however, if this is not practical, use a procedure similar to that for small quant. /Terphenyls/
Disposal Methods
SRP: At the time of review, criteria for land treatment or burial (sanitary landfill) disposal practices are subject to significant revision. Prior to implementing land disposal of waste residue (including waste sludge), consult with environmental regulatory agencies for guidance on acceptable disposal practices.
1. By making package of terphenyls in paper or other flammable material and burning in a suitable combustion chamber. 2. By dissolving terphenyls in a flammable solvent ... and atomizing in a suitable combustion chamber. /Terphenyls/
Spillage Disposal
Personal protection: particulate filter respirator adapted to the airborne concentration of the substance. Do NOT let this chemical enter the environment. Vacuum spilled material with specialist equipment. If appropriate, moisten first to prevent dusting. Carefully collect remainder. Then store and dispose of according to local regulations.
Preventive Measures
The worker should immediately wash the skin when it becomes contaminated.
Work clothing that becomes wet or significantly contaminated should be removed and replaced.
Workers whose clothing may have become contaminated should change into uncontaminated clothing before leaving the work premises.
독성 정보
Environmental Fate
TERRESTRIAL FATE: Based on a recommended classification scheme(1), an estimated Koc value of 3900(SRC), determined from a measured water solubility(2), indicates that o-terphenyl will have slight mobility in soil(SRC). Based on limited data o-terphenyl may be resistant to biodegradation(SRC). o-Terphenyl present in a waste water mixture, inoculated with three bacterial species, was not biodegraded after an incubation period of 130 hours(3). Volatilization of o-terphenyl may be important from moist soil surfaces(SRC) given an estimated Henry's Law constant of 6.2X10-5 atm-cu m/mole(SRC), from experimental values for water solubility(2) and vapor pressure(5), but not significant from dry soil surfaces(SRC) based on a vapor pressure of 2.5X10-4 mm Hg(SRC), determined from experimentally-derived coefficients(5).
AQUATIC FATE: Based on a recommended classification scheme(1), an estimated Koc of 3900(SRC), determined from a measured water solubility(2), indicates that o-terphenyl may adsorb to suspended solids and sediment in the water(SRC). Based on limited data o-terphenyl may be resistant to biodegradation(SRC). o-Terphenyl present in a waste water mixture, inoculated with three bacterial species, was not biodegraded after an incubation period of 130 hours(3). o-Terphenyl should volatilize from water surfaces based on an estimated Henry's Law constant of 6.1X10-5 atm-cu m/mole(SRC) from experimental values for water solubility(2) and vapor pressure(7). Estimated half-lives for a model river and model lake are 26 hours and 13 days, respectively(1,SRC). An experimental BCF value of 590(5), measured in goldfish, suggests that o-terphenyl will bioconcentrate in aquatic organisms(SRC), according to a recommended classification scheme(6).
ATMOSPHERIC FATE: According to a model of gas/particle partitioning of semivolatile organic compounds in the atmosphere(1), o-terphenyl, which has a vapor pressure of 2.5X10-4 mm Hg at 25 °C(2), determined from experimentally-derived coefficients, will exist in both the vapor and particulate phases in the ambient atmosphere. Vapor-phase o-terphenyl is degraded in the atmosphere by reaction with photochemically produced hydroxyl radicals(SRC); the half-life for this reaction in air is estimated to be about 2 days(3,SRC). Particulate-phase o-terphenyl may be physically removed from the air by dry deposition(SRC).
Exposure Routes
The substance can be absorbed into the body by ingestion and by inhalation.
inhalation, ingestion, skin and/or eye contact
Signs and Symptoms
Cough. Sore throat.
Redness. Pain.
Diarrhoea. Nausea. Vomiting.
irritation eyes, skin, mucous membrane; thermal skin burns; headache; sore throat; In Animals: liver, kidney damage
Soil Adsorption/Mobility
The Koc of o-terphenyl is estimated as approximately 3900(SRC), using an experimental water solubility of 1.24 mg/l(1) and a regression-derived equation(2,SRC). According to a recommended classification scheme(3), this estimated Koc value suggests that o-terphenyl has only slight mobility in soil(SRC).
TSCA Test Submissions
o-Terphenyl (CAS # 84-15-1) was evaluated for mutagenicity using the bacterium, Salmonella, at a concentration of 900 uM. No significant induced mutation occurred at the solubility limit. No further information was submitted.
m-Terphenyl (CAS # 92-06-8) was evaluated for mutagenicity using the bacterium, Salmonella, at a concentration of 900 uM. No significant induced mutation occurred at the solubility limit. No further information was submitted.
Human Toxicity Excerpts
... Concentrations of Santowax R vapor or condensate (a mixture of terphenyls containing 12% o-, 60% m-, and 28% p-terphenyl) in a reactor room under normal operating conditions ranged from 0.1 to 10 mg/cu m when the coolant was heated at 220 to 230 degree C. Concentrations above 10 mg/cu m (concentrations not specified) were associated with ocular and respiratory tract irritation in exposed workers. /Santowax R/
Artificial Pollution Sources
Terphenyl mixtures containing o-terphenyl are produced and used industrially as heat storage and transfer agents, as textile dye carriers, and as intermediates in the production of nonspreading lubricants(1) may result in o-terphenyl's release to the environment through various waste streams(SRC). From 1960-1970, technical grade terphenyls were also used as coolants for nuclear reactors, whereas contemporary use has been in solar-heating systems(1).
안전 데이터
- OEL
- Ceiling: 5 mg/m3 (0.5 ppm)
- wgk
- 3
- IDLA
- 500 mg/m3
- tsca
- TSCA listed
- rtecs
- WZ6472000
- ridadr
- UN 3077 9/PG 3
- 독성
- LD50 orally in Rabbit: 1900 mg/kg
- HS 번호
- 29029090
- risk_code
- 22-36/37/38-50/53-40-36/38-21/22-67-66-11-52/53-36-51/53
- hazard_code
- Xn,T,Xi,F,N
- safety_code
- 26-61-60-36/37-24/25-23-16-9
- 포장분류
- III
- 위험 등급
- 9
- Hazard Classifications
- Acute Tox. 3 InhalationAcute Tox. 4 OralAquatic Acute 1Aquatic Chronic 1Eye Irrit. 2
- 스토리지 클래스
- 6.1C - Combustible acute toxic Cat.3toxic compounds or compounds which causing chronic effects
- 유해 물질 데이터
- 84-15-1(Hazardous Substances Data)
화학 및 산업
약리 정보
Metabolism/Metabolites
MAJOR METABOLITES OF O- & M-TERPHENYL ARE GLUCOSIDURONIC ACIDS & FREE PHENOLS.
(14)C-LABELED O-TERPHENYL 80 MG/KG, ADMIN INTRAGASTRICALLY TO RATS, ABOUT 10% OF RADIOACTIVITY IN FECES DURING 1ST 24 HR WAS FOUND IN NON-METABOLIZED O-TERPHENYL, ABOUT 86% IN FREE PHENOLS, REMAINING 4% IN NON-HYDROLYZED, CONJUGATED POLAR METABOLITES.
(14)C-LABELED O-TERPHENYL 80 MG/KG ADMIN INTRAGASTRICALLY TO RABBITS, 12% OF RADIOACTIVITY IN URINE DURING 1ST 24 HR WAS FOUND IN NON-METABOLIZED O-TERPHENYL, 79% WAS FOUND IN FREE PHENOLS, & REMAINING 9% IN CONJUGATED POLAR METABOLITES.
Depending on the extent to which these compounds are absorbed, the various terphenyls were metabolized to glucuronic acid conjugates and phenol and excreted in the urine of treated rabbits. Following a single 1 gram oral dose of o-, m-, or p-terphenyl, 60% of the o-, 38% of the m-, and a trace of p-terphenyl were detected as their respective glucuronides in the urine. Zero, 15%, and 30% of the o-, m-, and p-terphenyls, respectively, were isolated unchanged in feces.
Absorption, Distribution and Excretion
AN INTRAGASTRIC DOSE OF (14)C LABELED O-TERPHENYL WAS RAPIDLY ABSORBED, DISTRIBUTED, AND ALMOST COMPLETELY EXCRETED WITHIN 48 HR, IN THE RAT MAINLY THROUGH THE BILE AND IN THE RABBIT MAINLY THROUGH URINARY EXCRETION. TEMPORARY ACCUM IN THE LIVER PEAKED AT 4.5 HR IN THE MOUSE AND WAS COMPLETELY CLEARED IN 1 WK.
RADIOACTIVITY FROM (14)C-LABELED O-TERPHENYL (80 MG/KG, INTRAGASTRICALLY) WAS ALMOST COMPLETELY EXCRETED WITHIN 48 HR PRIMARILY VIA BILIARY ROUTE IN RATS & URINARY TRACT IN RABBITS. DURING 1ST 24 HR, RATS EXCRETED 60% & RABBITS 72% OF ADMIN DOSE.
용도 및 제조
Uses
Terphenyl mixtures are used as heat transfer media, dye carriers, and in the production of lubricants; [ACGIH]
Terphenyl mixtures are used industrially as heat storage and transfer agents, as textile dye carriers, and as intermediates in the production of nonspreading lubricants. From 1960-1970, technical grade terphenyls were used as coolants for nuclear reactors, whereas contemporary use has been in solar-heating systems. /Terphenyl mixtures/
o-Terphenyl is used as a plasticizer for polystyrene for thermoplastic recording.
Methods of Manufacturing
Terphenyls are byproducts in the production of biphenyl by dehydrocondensation of benzene; they are found in the high-boiling fraction of the pyrolysis products. o-Terphenyl is readily separated from the terphenyl isomer mixture by distillation.
Formulations/Preparations
Santowax OM is composed of 64% o-terphenyl, 25% m-terphenyl, 6% p-terphenyl, and 5% diphenyl. A mixture of terphenyls, marketed as a heat-transfer medium in the late 1970s was composed of approximately 2-10% ortho-, 45-49% meta-, and 25-35% para-terphenyl with trace amounts of diphenyl, plus higher polyphenyls normally in the 2-18% range.
General Manufacturing Information
All Other Basic Organic Chemical Manufacturing
1,1':2',1''-Terphenyl: ACTIVE
IT /TERPHENYL/ OCCURS NATURALLY IN PETROLEUM OIL. ...3 CHEMICAL ISOMERS...OF WHICH ORTHO & PARA FORMS APPEAR INDUSTRIALLY MOST PREVALENT. /TERPHENYLS/
응용 분야
용도o-Terphenyl is used as a plasticizer for polystyrene for thermoplastic recording. Terphenyl mixtures are used industrially as heat storage and transfer agents, as textile dye carriers, and as intermediates in the production of nonspreading lubricants. From 1960-1970, technical grade terphenyls were used as coolants for nuclear reactors, whereas contemporary use has been in solar-heating systems.
일반 설명Colorless or light-yellow solid. Mp 58-59°C; bp: 337°C. Density: 1.16 g cm-3. Insoluble in water. Usually shipped as a solid mixture with its isomers m-terphenyl and p-terphenyl that is used as a heat-transfer fluid.
제조 방법
o-Terphenyl was synthesized via a Suzuki-Miyaura coupling between 2-bromobiphenyl and phenylboronic acid.
상·하류 제품 정보
상류 원료
하류 제품
관련 반응
연결된 노트
불러오는 중…