홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Nitromethane → 5-Cyano-2-(nitromethylthio)thiophene

HRID 1029768
인쇄

반응식

HRID 1029768 반응식
C([Li])CCC.CCCCCC.C(NC(C)C)(C)C.C(C1SC=CC=1)#N.[S].[Li].[C:28]([C:30]1[S:34][C:33]([SH:35])=[CH:32][CH:31]=1)#[N:29].[OH-].[Na+].[N+:38]([CH3:41])([O-:40])=[O:39]>CCOCC.O.[Fe-3](C#N)(C#N)(C#N)(C#N)(C#N)C#N.[K+].[K+].[K+]>[C:28]([C:30]1[S:34][C:33]([S:35][CH2:41][N+:38]([O-:40])=[O:39])=[CH:32][CH:31]=1)#[N:29]
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

13

반응물 9

HCID 6375NitromethaneHCID 7912DiisopropylamineHCID 8058HexaneHCID 14798Sodium HydroxideHCID 660872-ThiophenecarbonitrileHCID 3028194LithiumHCID 5362487SulfurHCID 19900837
5-Sulfanylthiophene-2-carbonitrile
HCID 178418339Butyllithium

생성물 1

HCID 199007545-Cyano-2-(nitromethylthio)thiophene수율 10%

시약·촉매·용매 3

HCID 178511488HCID 178511488, 화합물촉매HCID 962Water용매HCID 3283Diethyl Ether용매3회

반응 조건

온도
-70 °C

실험 절차

A 1.6 M solution of butyllithium in hexane (19.0 ml. 28 mmol) was added to a stirred solution of diisopropylamine (3.9 ml, 28 mmol) in dry ether (40 ml) at -70° C. under argon, and the resulting solution was stirred at -70° C. for 45 minutes. A solution of 2-cyanothiophene (2.6 ml, 28 mmol) in dry ether (10 ml) was then added. The mixture was stirred at -70° C, for 1 hour, then sulphur (1.27 g, 28 mmol) was added slowly at -50° C. After stirring the mixture at -50° C. for 1 hour, it was allowed to warm to ambient temperature and then stirred for a further 30 minutes. The resultant mixture, containing the lithium salt of 5-cyanothiophene-2-thiol, was diluted with ether (100 ml) and a solution of sodium hydroxide (1.68 g, 42 mmol) in water (100 ml) was added. Nitromethane (1.54 ml, 28 mmol) was then added to the vigorously stirred mixture followed by powdered potassium ferricyanide (9.34 g, 56 mmol), and the resultant mixture was stirred at ambient temperature for 1 hour. The mixture was filtered through diatomaceous earth to remove insoluble matter and the aqueous phase was separated and acidified to pH 1with 28% hydrochloric acid. The mixture was extracted with ethyl acetate, dried (MgSO4), and the solvent was removed by evaporation. The resultant oil (2.6 g) was purified by flash chromatography (Merck Kieselgel Art 9385) using ethyl acetate/hexane (1:4 v/v), to give 5-cyano-2-(nitromethylthio)thiophene as an oil (0.5 g, 10% yield); NMR: 5.4(s,2H), 7.4(q,2H).

후처리

  1. stirringThe mixture was stirred at -70° C, for 1 hour
  2. stirringAfter stirring the mixture at -50° C. for 1 hour
  3. temperatureto warm to ambient temperature
  4. stirringstirred for a further 30 minutes
  5. filtrationThe mixture was filtered through diatomaceous earth
  6. customto remove insoluble matter
  7. customthe aqueous phase was separated
  8. extractionThe mixture was extracted with ethyl acetate
  9. dry with materialdried (MgSO4)
  10. customthe solvent was removed by evaporation
  11. customThe resultant oil (2.6 g) was purified by flash chromatography (Merck Kieselgel Art 9385)

출처 및 근거

ORD 기록
ord-6533705d8bfa49b58c3212cffa611500
출처 데이터셋
uspto-grants-1992_04
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US05102905

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트