홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Dichloromethane → 4-(Perfluoro3-iodopropyl)phenyl acetate

HRID 1112134
인쇄

반응식

HRID 1112134 반응식
[C:1]([O:4][C:5]1[CH:10]=[CH:9][C:8](I)=[CH:7][CH:6]=1)(=[O:3])[CH3:2].[I:12][C:13]([F:22])([F:21])[C:14]([F:20])([F:19])[C:15]([F:18])([F:17])I.[Cl-].[NH4+].C(Cl)Cl>CS(C)=O.[Cu]>[C:1]([O:4][C:5]1[CH:10]=[CH:9][C:8]([C:15]([F:18])([F:17])[C:14]([F:20])([F:19])[C:13]([F:22])([F:21])[I:12])=[CH:7][CH:6]=1)(=[O:3])[CH3:2]
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

7

반응물 4

HCID 6344DichloromethaneHCID 25517Ammonium ChlorideHCID 1417934-IodophenylacetateHCID 109164621,1,2,2,3,3-Hexafluoro-1,3-diiodopropane

생성물 1

HCID 213310104-(Perfluoro3-iodopropyl)phenyl acetate수율 57.4%

시약·촉매·용매 2

HCID 23978
Copper
촉매
2회
HCID 679Dimethyl Sulfoxide용매

반응 조건

온도
120 °C

실험 절차

A solution of p-iodophenyl acetate (27.5 g, 105 mmol) and 1,3-diiodohexafluoropropane (52.0 g, 128.7 mmol) in 100 ml of anhydrous dimethyl sulfoxide was heated to 120° C. under nitrogen. Copper powder (13.5 g, 211 g atoms) was added to the vigorously stirred solution in five approximately equal amounts at 20 minute intervals. After the addition of copper was complete, the reaction mixture was stirred at 120° C. for an additional 1.5 hours. On cooling, saturated aqueous ammonium chloride together with methylene chloride was added to the reaction vessel. The excess copper and cuprous salts were filtered off, the organic layer was separated, and the aqueous layer was extracted with more methylene chloride. The organic extracts were combined, washed well with water, dried over anhydrous magnesium sulfate, and reduced in volume to a light yellow oil. The oil was refluxed in 25 ml of acetic anhydride for 45 minutes and the excess acetic anhydride and acetic acid were vacuum distilled. Distillation of the residual oil yielded 24.85 g of crude 4-(perfluoro3-iodopropyl)phenyl acetate, bp 126°-127° C./3.4 mm Hg, mp 75°-81° C. Recrystallization of this material from hexane gave 20.8 g (48% yield) of purer material, mp 84.5°-88° C. Repeated crystallization from hexane raised the melting point to 88.5°-89.5° C., which could not be improved upon by further recrystallization.

후처리

  1. temperatureOn cooling
  2. filtrationThe excess copper and cuprous salts were filtered off
  3. customthe organic layer was separated
  4. extractionthe aqueous layer was extracted with more methylene chloride
  5. washwashed well with water
  6. dry with materialdried over anhydrous magnesium sulfate
  7. temperatureThe oil was refluxed in 25 ml of acetic anhydride for 45 minutes
  8. distillationdistilled
  9. distillationDistillation of the residual oil

출처 및 근거

ORD 기록
ord-e539d2d715ea47c1906575ada128c31b
출처 데이터셋
uspto-grants-1978_10
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US04120900

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트