홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.1
  1. 홈
  2. /반응

Acetic Acid → Ethyl 2-formylbutanoate

HRID 1247636
인쇄

반응식

HRID 1247636 반응식
C(NC(C)C)(C)C.C([Li])CCC.[C:13]([O:18][CH2:19][CH3:20])(=[O:17])[CH2:14][CH2:15][CH3:16].[CH:21](OCC)=[O:22].C(O)(=O)C>O1CCCC1.ClCCl.O>[CH:21]([CH:14]([CH2:15][CH3:16])[C:13]([O:18][CH2:19][CH3:20])=[O:17])=[O:22]
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

9

반응물 5

HCID 176Acetic AcidHCID 7762Ethyl butyrateHCID 7912DiisopropylamineHCID 8025Ethyl formateHCID 178418339Butyllithium

생성물 1

HCID 289299Ethyl 2-formylbutanoate

시약·촉매·용매 3

HCID 962Water
용매
HCID 6344Dichloromethane용매
HCID 8028Tetrahydrofuran용매2회

반응 조건

온도
-75 °C

실험 절차

A solution of diisopropylamine (120.6 mL, 0.86 mol) (Aldrich) in tetrahyrofuran (370 mL) was cooled to −30° C. n-Butyllithium (2.5 M in hexanes, 344.2 mL, 0.86 mol) (Aldrich) was added drop wise at such a rate that the reaction mixture temperature was kept between −30 to 0° C. The reaction mixture was then cooled to −75° C. in a dry ice-acetone bath. A solution of ethyl butyrate (100 g, 0.86 mol) (Aldrich) in tetrahydrofuran (170 mL) was added drop wise over 28 minutes and keeping the reaction temperature between −75 to −70° C. The mixture was stirred at the same temperature for an additional 30 minutes. Ethyl formate (125 mL, 1.55 mol) (Aldrich) was then added to this mixture over 25 minutes and maintaining the temperature between −75 to −70° C. The resultant mixture was allowed to warm to room temperature and stirred at room temperature for 3 hours. With external cooling in a cold water bath to keep the reaction temperature below 30° C. acetic acid (98.55 mL, 1.72 mol) was added, followed by water (430 mL) and dichloromethane (200 mL). After separating the layers, the organic layer was washed with water (300 mL). The combined water layer was extracted with dichloromethane (200 mL). The combined organic layer was washed with aqueous sodium bicarbonate solution (200 mL). The basic aqueous solution was extracted with dichloromethane (100 mL). All organic layers were then combined, dried over sodium sulfate over night, filtered and distilled to remove solvent leaving about 180 mL. (Some of the product was distilled over with tetrahydrofuran.) The residue was distilled at 65–81° C. (23 mm Hg). The fraction distilling over at 70–81° C. (23 mm Hg) gave ethyl 2-formylbutyrate. (Yield 68.35 g, 55.1%).

후처리

  1. additionwas added drop wise at such a rate that the reaction mixture temperature
  2. customwas kept between −30 to 0° C
  3. custombetween −75 to −70° C
  4. temperaturemaintaining the temperature between −75 to −70° C
  5. temperatureto warm to room temperature
  6. stirringstirred at room temperature for 3 hours
  7. temperatureWith external cooling in a cold water bath
  8. additionwas added
  9. customAfter separating the layers
  10. washthe organic layer was washed with water (300 mL)
  11. extractionThe combined water layer was extracted with dichloromethane (200 mL)
  12. washThe combined organic layer was washed with aqueous sodium bicarbonate solution (200 mL)
  13. extractionThe basic aqueous solution was extracted with dichloromethane (100 mL)
  14. dry with materialdried over sodium sulfate over night
  15. filtrationfiltered
  16. distillationdistilled
  17. customto remove solvent
  18. customleaving about 180 mL
  19. distillation(Some of the product was distilled over with tetrahydrofuran
  20. distillation) The residue was distilled at 65–81° C. (23 mm Hg)
  21. distillationThe fraction distilling over at 70–81° C. (23 mm Hg)

출처 및 근거

ORD 기록
ord-215fa38ec5664781b60cbf58a8b7bb7b
출처 데이터셋
uspto-grants-2006_10
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US07129351B2

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트