홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Sulfuric Acid → Di-tert-amylcyclohexylphosphine

HRID 1297573
인쇄

반응식

HRID 1297573 반응식
[C:1]([P:6](Cl)[C:7]([CH2:10][CH3:11])([CH3:9])[CH3:8])([CH2:4][CH3:5])([CH3:3])[CH3:2].[CH:13]1(Cl)[CH2:18][CH2:17][CH2:16][CH2:15][CH2:14]1.[Mg].S(=O)(=O)(O)O>O1CCCC1.[Cu]Cl.C1(C)C=CC=CC=1>[C:1]([P:6]([C:7]([CH2:10][CH3:11])([CH3:9])[CH3:8])[CH:13]1[CH2:18][CH2:17][CH2:16][CH2:15][CH2:14]1)([CH2:4][CH3:5])([CH3:3])[CH3:2]
참가 물질실험 절차후처리출처 및 근거반응 노트

참가 물질

8

반응물 4

HCID 1118Sulfuric AcidHCID 10952ChlorocyclohexaneHCID 5462224MagnesiumHCID 23032008Di-tert-amylphosphinous chloride

생성물 1

HCID 22925481Di-tert-amylcyclohexylphosphine수율 96.7%

시약·촉매·용매 3

HCID 62652Cuprous chloride촉매
HCID 1140Toluene용매
HCID 8028Tetrahydrofuran용매2회

실험 절차

In a 300 ml four-necked flask thoroughly purged with nitrogen, 10.4 g (0.05 mol) of di-tert-amylphosphinous chloride, 0.10 g (0.001 mol (corresponding to 2% by mol)) of copper(I) chloride and 30 ml of tetrahydrofuran were placed. To the contents of the flask, a Grignard reagent solution previously prepared from 8.3 g (0.060 mol) of cyclohexyl chloride and 2.0 g (0.08 mol) of metallic magnesium in 50 ml of tetrahydrofuran was dropwise added over a period of 1 hour with maintaining the temperature at 25° C. to 30° C. After the dropwise addition was completed, stirring was conducted at a temperature of 35° C. to 40° C. for 6 hours. After the temperature of the reaction solution was returned to room temperature, 20 ml of toluene and 20 ml of a 5% sulfuric acid aqueous solution were added to the reaction solution to perform liquid separation. Then, the organic layer was washed with water and dried over anhydrous sodium sulfate. The solvent and a low-boiling component were distilled off under reduced pressure to obtain 12.4 g (purity: 94.9%) of the aimed di-tert-amylcyclohexylphosphine as an oily substance. The yield was 90.2%.

후처리

  1. additionwas dropwise added over a period of 1 hour
  2. temperaturewith maintaining the temperature at 25° C. to 30° C
  3. additionAfter the dropwise addition
  4. customwas returned to room temperature
  5. customliquid separation
  6. washThen, the organic layer was washed with water
  7. dry with materialdried over anhydrous sodium sulfate
  8. distillationThe solvent and a low-boiling component were distilled off under reduced pressure

출처 및 근거

ORD 기록
ord-b131fcae618b4d9db60a8b5908619afd
출처 데이터셋
uspto-grants-2007_07
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US07250535B2

반응 노트

이 페이지에서참가 물질실험 절차후처리출처 및 근거반응 노트