홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.0
  1. 홈
  2. /반응

Hydrochloric Acid → 3-Acetyl-5-bromopyridine

HRID 13769
노트
인쇄 미리보기

반응식

HRID 13769 반응식
[Cl-].[Mg+2].[Cl-].[C:4](OCC)(=O)CC(OCC)=O.[Br:15][C:16]1[CH:17]=[N:18][CH:19]=[C:20]([CH:24]=1)[C:21](Cl)=[O:22].Cl>C1(C)C=CC=CC=1.C(N(CC)CC)C>[C:21]([C:20]1[CH:19]=[N:18][CH:17]=[C:16]([Br:15])[CH:24]=1)(=[O:22])[CH3:4]
참가 물질실험 절차후처리출처 및 근거반응 노트

참가 물질

7

반응물 4

HCID 313Hydrochloric AcidHCID 7761Diethyl MalonateHCID 27812235-Bromonicotinoyl chlorideHCID 5360315Magnesium Chloride

생성물 1

HCID 8204233-Acetyl-5-bromopyridine수율 24.3%

시약·촉매·용매 2

HCID 1140Toluene용매2회
HCID 8471
Triethylamine
용매

실험 절차

1.24 g of ground magnesium chloride was suspended in 13 ml of toluene and 6.2 ml of triethylamine and 2.93 g of diethyl malonate were added in turn. After stirring at room temperature for 1.5 hours, a suspension of 4.08 g of 5-bromonicotinoyl chloride obtained in the step 1 in 10 ml of toluene was added dropwise over 15 minutes, followed by stirring at room temperature for 2 hours. After neutralizing with 40 ml of 1N hydrochloric acid, the aqueous layer was separated. The aqueous layer was further subjected to extraction with diethyl ether and the organic layers were combined, and then the solvent was distilled off under reduced pressure. To the resulting oily product, dimethyl sulfoxide-water (17 ml-0.7 ml) was added, followed by stirring with heating at 150 to 160° C. for 2 hours. The reaction solution was air-cooled, and then water was added. Then, the deposited crystals were collected by filtration. The deposited crystals were dissolved in ethyl acetate, washed in turn with water and an aqueous saturated sodium hydrogen carbonate solution and then dried over anhydrous magnesium sulfate. 0.60 g of activated carbon (Kyoryoku Shirasagi MOIWY433) was added and, after standing for 10 minutes, activated carbon was removed by filtration, the filtrate was concentrated under reduced pressure. The residue was purified by silica gel column chromatography to obtain 0.89 g of the objective compound as pale yellow crystals.

후처리

  1. additionwas added dropwise over 15 minutes
  2. stirringby stirring at room temperature for 2 hours
  3. customthe aqueous layer was separated
  4. extractionThe aqueous layer was further subjected to extraction with diethyl ether
  5. distillationthe solvent was distilled off under reduced pressure
  6. additionTo the resulting oily product, dimethyl sulfoxide-water (17 ml-0.7 ml) was added
  7. stirringby stirring
  8. temperaturewith heating at 150 to 160° C. for 2 hours
  9. temperatureThe reaction solution was air-cooled
  10. additionwater was added
  11. filtrationThen, the deposited crystals were collected by filtration
  12. dissolutionThe deposited crystals were dissolved in ethyl acetate
  13. washwashed in turn with water
  14. dry with materialan aqueous saturated sodium hydrogen carbonate solution and then dried over anhydrous magnesium sulfate
  15. addition0.60 g of activated carbon (Kyoryoku Shirasagi MOIWY433) was added
  16. waitafter standing for 10 minutes
  17. customactivated carbon was removed by filtration
  18. concentrationthe filtrate was concentrated under reduced pressure
  19. customThe residue was purified by silica gel column chromatography

출처 및 근거

ORD 기록
ord-b35366e3ab30431a8e14e9e775e2da34
출처 데이터셋
uspto-grants-2010_06
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US07728131B2

반응 노트

불러오는 중…

이 페이지에서참가 물질실험 절차후처리출처 및 근거반응 노트