홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Ammonium Chloride → Methyl (S)-2-benzyloxycarbonylamino-4-oxopentanoate

HRID 1664706
인쇄

반응식

HRID 1664706 반응식
[Br-].[Li+].[CH3:3][Mg]Cl.[CH2:6]([O:13][C:14]([NH:16][C@@H:17]([CH2:22][C:23](Cl)=[O:24])[C:18]([O:20][CH3:21])=[O:19])=[O:15])[C:7]1[CH:12]=[CH:11][CH:10]=[CH:9][CH:8]=1.[Cl-].[NH4+]>C1COCC1.[Cu]Br.[Cu](Br)Br>[CH2:6]([O:13][C:14]([NH:16][C@@H:17]([CH2:22][C:23](=[O:24])[CH3:3])[C:18]([O:20][CH3:21])=[O:19])=[O:15])[C:7]1[CH:12]=[CH:11][CH:10]=[CH:9][CH:8]=1
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

8

반응물 4

HCID 25517Ammonium ChlorideHCID 82050Lithium BromideHCID 11055664Methyl (S)-2-benzyloxycarbonylamino-3-chlorocarbonylpropionateHCID 178418332HCID 178418332, 화합물

생성물 1

HCID 13857370Methyl (S)-2-benzyloxycarbonylamino-4-oxopentanoate수율 84%

시약·촉매·용매 3

HCID 24593
copper(I) bromide
촉매
HCID 24611Copper bromide (CuBr2)촉매
HCID 8028Tetrahydrofuran용매3회

반응 조건

온도
-60 °C

실험 절차

Copper(I) bromide (60.9 g, 425 mmol, 1.2 equivalents (eq.)) was introduced into a 3 liter 4-neck flask (with dropping funnel, internal thermometer, argon inlet, rubber septa, in a cooling bath) and admixed with 250 ml of THF. A separate flask was initially charged at 10° C. with lithium bromide (75 g, 864 mmol, 2.4 eq.) and admixed with 470 ml of THF under argon. On completion of dissolution and recooling to RT, this solution was transferred to the suspension of the copper bromide. The resulting colorless to slightly greenish solution was cooled to −60° C., and methylmagnesium chloride (141 ml of a 3.0 M solution in THF, 423 mmol) was added within 15 min. A thick yellowish precipitate formed and the temperature rose to RT. After cooling again to −60° C., the solution from example 1 (prepared from 106 g of methyl (S)-2-benzyloxycarbonylamino-3-chlorocarbonylpropionate, 353 mmol, and 360 ml of THF) was added over about 30 min and the temperature was kept below −25° C. After the addition had ended, the mixture was stirred for another 1 h, and solid ammonium chloride (30 g) was added at −15° C. After a further 2 h, the mixture was filtered, the filtrate was diluted with 400 ml of heptane and 200 ml of saturated ammonium chloride solution were added. Once the mixture had been stirred at RT for 1 h, the organic phase was removed and washed repeatedly, and the aqueous phases were reextracted with ethyl acetate. The combined organic phases were dried over sodium sulfate, concentrated on a rotary evaporator under reduced pressure and chromatographed on 1 kg of silica gel with 1:3 to 1:1 ethyl acetate/heptane. After the products had been combined and dried under reduced pressure, 83 g (84% yield) of a white solid were obtained. 1H NMR (300 MHz, CDCl3): 7.4 (m, 5H); 5.78 (m, 1H); 5.18 (s, 2H); 4.6 (s, 1H); 3.75 (“s”, 3H); 3.3-2.9 (2dd, 2H); 2.2 (s, 3H)

후처리

  1. dissolutionOn completion of dissolution
  2. customrecooling to RT
  3. customA thick yellowish precipitate formed
  4. customrose to RT
  5. temperatureAfter cooling again to −60° C.
  6. customwas kept below −25° C
  7. additionAfter the addition
  8. waitAfter a further 2 h
  9. filtrationthe mixture was filtered
  10. additionthe filtrate was diluted with 400 ml of heptane and 200 ml of saturated ammonium chloride solution
  11. additionwere added
  12. stirringOnce the mixture had been stirred at RT for 1 h
  13. customthe organic phase was removed
  14. washwashed repeatedly
  15. dry with materialThe combined organic phases were dried over sodium sulfate
  16. concentrationconcentrated on a rotary evaporator under reduced pressure
  17. customchromatographed on 1 kg of silica gel with 1:3 to 1:1 ethyl acetate/heptane
  18. customdried under reduced pressure

출처 및 근거

ORD 기록
ord-fc825739436044b58da5d54ab8b4e06e
출처 데이터셋
uspto-grants-2011_10
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US08039480B2

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트