홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

tert-Butyl hydroperoxide → Acrylic acid hydroxyethyl methacrylate

HRID 1903279
인쇄

반응식

HRID 1903279 반응식
[C:1]([OH:5])(=[O:4])[CH:2]=[CH2:3].[C:6]([O:11][CH2:12][CH2:13][OH:14])(=[O:10])[C:7]([CH3:9])=[CH2:8].S(OOS([O-])(=O)=O)([O-])(=O)=O.[NH4+].[NH4+].C(OO)(C)(C)C.C=O.S([O-])[O-].[Na+].[Na+].[OH-].[Na+]>O>[C:1]([OH:5])(=[O:4])[CH:2]=[CH2:3].[C:6]([O:11][CH2:12][CH2:13][OH:14])(=[O:10])[C:7]([CH3:9])=[CH2:8]
참가 물질실험 절차후처리출처 및 근거반응 노트

참가 물질

8

반응물 6

HCID 6410tert-Butyl hydroperoxideHCID 6581Acrylic AcidHCID 133602-Hydroxyethyl MethacrylateHCID 14798Sodium HydroxideHCID 62648Ammonium Persulfate3회HCID 21225536CID 21225536

생성물 1

HCID 10330472
Acrylic acid hydroxyethyl methacrylate

시약·촉매·용매 1

HCID 962Water용매5회

실험 절차

Into a 5 liter 3-neck round bottom flask is charged 2960 ml of deionized (DI) water. The water is heated with a heating mantle to 85°-87° C. while being stirred with a mechanical stirrer. While this is being done, 416 g of acrylic acid (AA) and 104 g of 2-hydroxyethyl methacrylate (HEMA) are charged into a one-liter graduated separatory funnel. A 1 wt.% aqueous solution of ammonium persulfate (APS) is also prepared. When the temperature of the water levels off at 85°-87° C., 13 ml of the 1 wt.% APS solution is added to the reactor. The monomer solution and a co-feed catalyst of 52 ml of the 1 wt.% APS solution are then added gradually and proportionally to the reactor over a period of about two hours. During the addition the temperature is maintained at 85°-87° C. and agitation is increased gradually to maintain good stirring. After the additions are completed the polymer solution is held at 85°-87° C. for 30 minutes. At the end of the 30 minute time period an additional catalyst system consisting of 0.4 g of tertiary butyl hydroperoxide diluted in 10 ml of DI water and 0.3 g of sodium sulfoxylate formaldehyde dissolved in 10 ml of DI water are added. Stirring is continued for 30 minutes. A neutralizer consisting of 232 g of 50% sodium hydroxide is added. Stirring is continued for about 30 minutes. The product obtained is a clear solution with a viscosity of about 7000 cps (Brookfield Viscometer, 12 rpm, spindle 3, 20° C.±2° C.) and has a polymer solids content of 15.4% with about 50% of the acid groups neutralized.

후처리

  1. additionDuring the addition the temperature
  2. temperatureis maintained at 85°-87° C.
  3. temperatureagitation is increased gradually
  4. temperatureto maintain good stirring
  5. customAt the end of the 30 minute time period
  6. additionare added
  7. stirringStirring
  8. waitis continued for 30 minutes
  9. additionis added
  10. stirringStirring
  11. waitis continued for about 30 minutes
  12. customThe product obtained
  13. customof about 7000 cps (Brookfield Viscometer, 12 rpm, spindle 3, 20° C.±2° C.)

출처 및 근거

ORD 기록
ord-eea9296acd27493fb26cca0b45d45638
출처 데이터셋
uspto-grants-1984_03
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US04435539

반응 노트

이 페이지에서참가 물질실험 절차후처리출처 및 근거반응 노트