홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Dichloromethane → 2H-Pyran, 2-[(1-ethynylhexyl)oxy]tetrahydro-

HRID 222843
인쇄

반응식

HRID 222843 반응식
[O:1]1[CH:6]=[CH:5][CH2:4][CH2:3][CH2:2]1.[CH3:7][C:8]1[CH:9]=[CH:10][C:11](S(O)(=O)=O)=[CH:12][CH:13]=1.[OH2:18].Cl[CH2:20]Cl>>[C:13]([CH:12]([O:18][CH:6]1[CH2:5][CH2:4][CH2:3][CH2:2][O:1]1)[CH2:11][CH2:10][CH2:9][CH2:8][CH3:7])#[CH:20]
참가 물질실험 절차후처리출처 및 근거반응 노트

참가 물질

4

반응물 3

HCID 6344DichloromethaneHCID 80803,4-dihydro-2H-pyranHCID 521998p-Toluenesulfonic acid monohydrate

생성물 1

HCID 117890622H-Pyran, 2-[(1-ethynylhexyl)oxy]tetrahydro-수율 85%

실험 절차

S-2-(1-Ethynyl-hexyloxy)-tetrahydropyran. To a solution of S-oct-1-yn-3-ol (900 mg, 7.13 mmol) and 3,4-dihydro-2H-pyran (901 mg, 10.7 mMol) in 5 mL dichloromethane, TsOH.H2O (13 mg, 0.071 mMol) was added. After the addition was completed, the reaction mixture was stirred for 12 h and quenched with saturated aq. NaHCO3. The mixture was extracted with DCM (20 mL×3) and washed with water (20 mL×2). After drying over Na2SO4 the solvent was removed and the product was purified by silica gel chromatography (AcOEt:hexane=1:10) to afford 2-(1-ethynyl-hexyloxy)tetrahydropyran (1.27 g, 85%) as colorless liquid. The product was a mixture of two diastereomers (ratio 1:5.8). Major diastereomer: 1H NMR (500 MHz, CDCl3) δ 4.98-4.97 (m, 1H), 4.40-4.43 (m, 1H), 3.79-3.83 (m, 1H), 3.53-3.55 (m, 1H), 2.38 (s, 1H), 1.71-1.84 (m, 4H), 1.44-1.62 (m, 6H), 1.33-1.34 (m, 4H), 0.91 (t, J=6.5 Hz, 3H) b. 2-[1-(3-Bromo-3,3-difluoro-prop-1-ynyl)-hexyloxy]-tetrahydro-pyran. To a solution of S-2-(1-ethynyl-hexyloxy)tetrahydropyran (1.24 g, 5.9 mmol) in dry THF 30 mL, a 2.5 M hexane solution of n-butyllithium (2.36 mL, 5.9 mmol) was added dropwise at approximately −90° C. (liquid N2/EtOH bath) under an argon atmosphere. After the reaction mixture was stirred for 30 minutes at that temperature, the reaction mixture was cooled to −110° C. (because the solvent along the wall of reaction flask froze at −110° C., it is helpful to maintain good stirring throughout). Cold dibromodifluoromethane (5.5 mL, 60 mmol) was added to the mixture by cannulation. The temperature of the reaction mixture was controlled very carefully during the addition of CF2Br2 using a thermometer immersed in the reaction mixture. The reaction temperature may rise to −90° C. or even higher even if CF2Br2 is introduced slowly. After the addition was completed, the mixture was allowed to warm to −50° C. with stirring during the course of 1 hour and quenched with sat. aq. NH4Cl (50 mL). The aqueous layer was extracted with ether (50 mL) and the organic layer was washed by water (10 mL×3). The organic layer was dried over Na2SO4. After evaporation of the solvent, the product was purified by silica gel chromatography (AcOEt:Hexane=1:10) to afford product (1.5 g, 75%) as colorless liquid. The product is mixture of two diastereomers (ratio 1:9.5). Major diastereomer:

후처리

  1. additionAfter the addition
  2. customquenched with saturated aq. NaHCO3
  3. extractionThe mixture was extracted with DCM (20 mL×3)
  4. washwashed with water (20 mL×2)
  5. dry with materialAfter drying over Na2SO4 the solvent
  6. customwas removed
  7. customthe product was purified by silica gel chromatography (AcOEt:hexane=1:10)

출처 및 근거

ORD 기록
ord-bcd30cc119b749bc8af79702e10f00a6
출처 데이터셋
uspto-grants-2012_06
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US08207381B2

반응 노트

이 페이지에서참가 물질실험 절차후처리출처 및 근거반응 노트