홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Potassium Carbonate → 3-(Dibenzothiophen-4-yl)-9H-carbazole

HRID 239996
인쇄

반응식

HRID 239996 반응식
Br[C:2]1[CH:3]=[CH:4][C:5]2[NH:6][C:7]3[C:12]([C:13]=2[CH:14]=1)=[CH:11][CH:10]=[CH:9][CH:8]=3.[CH:15]1[C:23]2[C:22]3[CH:24]=[CH:25][CH:26]=[CH:27][C:21]=3[S:20][C:19]=2[C:18](B(O)O)=[CH:17][CH:16]=1.C1(C)C=CC=CC=1P(C1C=CC=CC=1C)C1C=CC=CC=1C.C(=O)([O-])[O-].[K+].[K+]>C([O-])(=O)C.[Pd+2].C([O-])(=O)C.C(O)C.C1(C)C=CC=CC=1>[CH:15]1[C:23]2[C:22]3[CH:24]=[CH:25][CH:26]=[CH:27][C:21]=3[S:20][C:19]=2[C:18]([C:2]2[CH:3]=[CH:4][C:5]3[NH:6][C:7]4[C:12]([C:13]=3[CH:14]=2)=[CH:11][CH:10]=[CH:9][CH:8]=4)=[CH:17][CH:16]=1
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

8

반응물 4

HCID 11430Potassium CarbonateHCID 80271Tri-o-tolylphosphineHCID 2524463-BromocarbazoleHCID 2734329Dibenzothiophene-4-boronic acid

생성물 1

HCID 666918723-(Dibenzothiophen-4-yl)-9H-carbazole수율 32%

시약·촉매·용매 3

HCID 167845
palladium(II) acetate
촉매
HCID 702Ethanol용매
HCID 1140Toluene용매

반응 조건

온도
110 °C

실험 절차

In a 200-mL three-neck flask were put 3.0 g (12 mmol) of 3-bromocarbazole, 2.8 g (12 mmol) of dibenzothiophene-4-boronic acid, and 150 mg (0.5 mol) of tri(ortho-tolyl)phosphine, and the air in the flask was replaced with nitrogen. To this mixture were added 40 mL of toluene, 40 mL of ethanol, and 15 mL (2.0 mol/L) of an aqueous potassium carbonate solution. In the flask, the mixture was degassed by being stirred under reduced pressure. After the degassing, replacement with nitrogen was performed, and 23 mg (0.10 mmol) of palladium(II) acetate was added to this mixture, and then the mixture was refluxed at 110° C. for 3 hours. After the reflux, the mixture was cooled to room temperature, and then the precipitated solid was collected by suction filtration. The collected solid was dissolved in 100 mL of toluene, and this solution was filtered through Celite (produced by Wako Pure Chemical Industries, Ltd., Catalog No. 531-16855), Florisil (produced by Wako Pure Chemical Industries, Ltd., Catalog No. 540-00135), and alumina. The solid obtained by concentration of the obtained filtrate was recrystallized from toluene/hexane, so that 1.4 g of a white solid, which was the object of the synthesis, was obtained in 32% yield. The synthesis scheme of Step 1 is illustrated in (a-1).

후처리

  1. customIn a 200-mL three-neck flask were put
  2. customIn the flask, the mixture was degassed
  3. temperatureAfter the reflux, the mixture was cooled to room temperature
  4. filtrationthe precipitated solid was collected by suction filtration
  5. dissolutionThe collected solid was dissolved in 100 mL of toluene
  6. filtrationthis solution was filtered through Celite (produced by Wako Pure Chemical Industries, Ltd., Catalog No. 531-16855), Florisil (produced by Wako Pure Chemical Industries, Ltd., Catalog No. 540-00135), and alumina
  7. customThe solid obtained by concentration of the obtained filtrate
  8. customwas recrystallized from toluene/hexane, so that 1.4 g of a white solid, which
  9. customthe object of the synthesis
  10. customwas obtained in 32% yield
  11. customThe synthesis scheme of Step 1

출처 및 근거

ORD 기록
ord-d773b476ff1e440daa844eb556aa9750
출처 데이터셋
uspto-grants-2014_02
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US08642782B2

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트