홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Ethyl bromoacetate → Bis(2-ethyloxycarbonylmethylthioethyl) sulfide

HRID 266907
인쇄

반응식

HRID 266907 반응식
[SH:1][CH2:2][CH2:3][S:4][CH2:5][CH2:6][SH:7].[OH-].[Na+].Br[CH2:11][C:12]([O:14][CH2:15][CH3:16])=[O:13].[C:17]([O:20][CH2:21][CH3:22])(=[O:19])[CH3:18]>C(C(C)=O)C>[CH2:15]([O:14][C:12]([CH2:11][S:1][CH2:2][CH2:3][S:4][CH2:5][CH2:6][S:7][CH2:18][C:17]([O:20][CH2:21][CH3:22])=[O:19])=[O:13])[CH3:16]
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

6

반응물 4

HCID 7748Ethyl bromoacetateHCID 8857Ethyl AcetateHCID 14798Sodium HydroxideHCID 77117Bis(2-mercaptoethyl) sulfide

생성물 1

HCID 53861893Bis(2-ethyloxycarbonylmethylthioethyl) sulfide

시약·촉매·용매 1

HCID 6569Methyl Ethyl Ketone용매

반응 조건

온도
5 °C

실험 절차

In 360 ml of methyl ethyl ketone was dissolved 27.8 g of bis(2-mercaptoethyl)sulfide, and the solution was then cooled to 5° C. Next, 32 g of a 45% aqueous sodium hydroxide solution was added dropwise thereto, followed by vigorous stirring. To this solution, 60 g of ethyl bromoacetate was added dropwise, and reaction was then carried out at room temperature for 1 hour. Afterward, 200 ml of ethyl acetate was added thereto, and the solution was washed with 50 ml of an aqueous saturated ammonium chloride solution twice, and then dried over anhydrous sodium sulfate. Afterward, the solvent was distilled off under reduced pressure to obtain 44 g of light yellow oily bis(2-ethyloxycarbonylmethylthioethyl) sulfide. This sulfide was dissolved in 70 ml of isopropanol, and 18 g of hydrazine monohydrate was added dropwise thereto, while a solution temperature of 5° C. was maintained. After 2 hours, the produced white crystalline bis(2-hydrazinocarbonylmethylthioethyl) sulfide was collected by filtration. Next, the collected crystals were washed with 20 ml of cold isopropanol twice and further washed with 10 ml of hexane. After drying, the dried material was dissolved in 150 ml of water and then cooled to 5° C., and 25 g of concentrated hydrochloric acid was then added dropwise thereto. Furthermore, a solution obtained by dissolving 16 g of sodium nitrite in 50 ml of water was added dropwise thereto. After 30 minutes, 150 ml of benzene was added thereto, and the solution was then heated up to room temperature, while vigorously stirred. Next, the resulting organic layer was separated, and then dried over anhydrous magnesium sulfate. Afterward, toluene was added thereto for dilution so as to bring the total volume to 500 ml, and the solution was then slowly heated up to 55° C. to gently carry out reaction so that nitrogen might be continuously generated. After the reaction at 70° C. for 3 hours, the solution was cooled to room temperature and then allowed to stand overnight, and the resulting white precipitate was removed by filtration. Afterward, the solvent was distilled off under reduced pressure. The obtained colorless oily product was distilled at 80° C. under a reduced pressure of 0.3 mmHg for 2 hours to remove impurities, thereby obtaining the desired bis[2-(isocyanatomethylthio)ethyl]sulfide.

후처리

  1. customreaction
  2. washthe solution was washed with 50 ml of an aqueous saturated ammonium chloride solution twice
  3. dry with materialdried over anhydrous sodium sulfate
  4. distillationAfterward, the solvent was distilled off under reduced pressure

출처 및 근거

ORD 기록
ord-3ec3d807cd51441e9ba110f51e820d72
출처 데이터셋
uspto-grants-1997_07
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US05652321

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트