홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Formaldehyde → 4-Phenoxy-2-butynyl acetate

HRID 349606
인쇄

반응식

HRID 349606 반응식
[CH2:1]([O:4][C:5]1[CH:10]=[CH:9][CH:8]=[CH:7][CH:6]=1)[C:2]#[CH:3].C([Li])CCC.C=O.N1C=CC=CC=1.[C:24]([O:27][C:28](=O)C)(=[O:26])[CH3:25]>C1COCC1>[C:24]([O:27][CH2:28][C:3]#[C:2][CH2:1][O:4][C:5]1[CH:10]=[CH:9][CH:8]=[CH:7][CH:6]=1)(=[O:26])[CH3:25]
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

7

반응물 5

HCID 712FormaldehydeHCID 1049PyridineHCID 7918Acetic AnhydrideHCID 83613(Prop-2-ynyloxy)benzeneHCID 178418339Butyllithium

생성물 1

HCID 105843294-Phenoxy-2-butynyl acetate수율 87%

시약·촉매·용매 1

HCID 8028
Tetrahydrofuran
용매
2회

반응 조건

온도
-20 °C

실험 절차

A 0.5-L reactor (#1) was equipped with a thermometer, an addition funnel, an overhead stirrer, and a nitrogen inlet. 150 mL of THF was charged followed by 27.5 g (0.21 mole) of phenyl propargyl ether. The solution was cooled to −20° C. 100 mL (0.25 mole) of n-butyllithium in hexanes was charged into an addition funnel. This solution was added to the reactor at a temperature between −25 and −35° C. The temperature was controlled by the rate of addition and the mixture was stirred for 1 h at −25 to −35° C. A second 1-L reactor (#2) was equipped with a thermometer, an overhead stirrer and a cannulation device. 120 mL of THF was charged followed by 9.4 g (0.42 mol) of paraformaldehyde as a solid in one portion. The resulting suspension was stirred for 5 min. and cooled to 5–10° C. The contents of reactor #1 were cannulated into reactor #2 maintaining temperature in reactor #2 between 5 and 15° C. The temperature in reactor #1 was maintained below −15° C. The cooling bath from reactor #2 was removed and the reaction mixture was allowed to warm up slowly to 20–25° C. Stirring was continued for 16 h at ambient temperature. 200 mL of water was added to the reaction mixture and the mixture was stirred for 15–30 min at ambient temperature. The reaction mixture was extracted twice with 200 mL and then 100 mL of ethyl acetate. The combined organic solution was washed with 200 mL of water. The organic solution was dried with 50 g of anhydrous sodium sulfate. The drying agent was filtered off and rinsed with 50 mL of ethyl acetate. The filtrate was transferred into a 1-L reactor fitted with an overhead stirrer. Pyridine (67 mL, 0.83 mol) was charged followed by acetic anhydride (39 mL, 0.42 mol). The solution was stirred overnight at ambient temperature. The solution was washed sequentially with water (200 mL), sodium bicarbonate solution (2×150 mL) until pH=7–8, hydrochloric acid solution (2×150 mL) until pH=1–3, and brine (1×150 mL). The solution was dried with anhydrous sodium sulfate (50 g). The drying agent was filtered off, and the filtrate was concentrated in vacuo at a temperature that did not exceed 60° C. to yield 37 g (87% yield, HPLC strength 65%) of product as a dark-red slightly viscous fluid.

후처리

  1. additionThis solution was added to the reactor at a temperature between −25 and −35° C
  2. additionThe temperature was controlled by the rate of addition
  3. stirringThe resulting suspension was stirred for 5 min.
  4. temperaturecooled to 5–10° C
  5. customThe contents of reactor #1 were cannulated into reactor
  6. custom#2 between 5 and 15° C
  7. temperatureThe temperature in reactor #1 was maintained below −15° C
  8. customThe cooling bath from reactor #2 was removed
  9. temperatureto warm up slowly to 20–25° C
  10. stirringStirring
  11. waitwas continued for 16 h at ambient temperature
  12. addition200 mL of water was added to the reaction mixture
  13. stirringthe mixture was stirred for 15–30 min at ambient temperature
  14. extractionThe reaction mixture was extracted twice with 200 mL
  15. washThe combined organic solution was washed with 200 mL of water
  16. dry with materialThe organic solution was dried with 50 g of anhydrous sodium sulfate
  17. filtrationThe drying agent was filtered off
  18. washrinsed with 50 mL of ethyl acetate
  19. customThe filtrate was transferred into a 1-L reactor
  20. customfitted with an overhead stirrer
  21. stirringThe solution was stirred overnight at ambient temperature
  22. washThe solution was washed sequentially with water (200 mL), sodium bicarbonate solution (2×150 mL) until pH=7–8, hydrochloric acid solution (2×150 mL) until pH=1–3, and brine (1×150 mL)
  23. dry with materialThe solution was dried with anhydrous sodium sulfate (50 g)
  24. filtrationThe drying agent was filtered off
  25. concentrationthe filtrate was concentrated in vacuo at a temperature that
  26. customdid not exceed 60° C.
  27. customto yield 37 g (87% yield, HPLC strength 65%) of product as a dark-red slightly viscous fluid

출처 및 근거

ORD 기록
ord-f0007eb910ae49088d3df96af4e35434
출처 데이터셋
uspto-grants-2007_02
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US07179911B2

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트