홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Methanol → 5-Norbornene-2-carboxylic acid

HRID 368924
인쇄

반응식

HRID 368924 반응식
[CH:1]12[CH2:7][CH:4]([CH2:5][CH2:6]1)[CH:3]=[CH:2]2.C(Cl)Cl.C[OH:12].CC(=C)C.C1[CH2:21][O:20]CC1>[CH2-]C=C.[CH2-]C=C.Cl[Pd+].Cl[Pd+].F[Sb-](F)(F)(F)(F)F.[Ag+]>[CH:1]12[CH2:7][CH:4]([CH:5]([C:21]([OH:20])=[O:12])[CH2:6]1)[CH:3]=[CH:2]2
참가 물질실험 절차후처리출처 및 근거반응 노트

참가 물질

8

반응물 5

HCID 887MethanolHCID 6344Dichloromethane3회HCID 8028TetrahydrofuranHCID 8255IsobutyleneHCID 103522-Norbornene2회

생성물 1

HCID 789495-Norbornene-2-carboxylic acid

시약·촉매·용매 2

HCID 61538
Palladium, di-mu-chlorobis(eta3-2-propenyl)di-
촉매
2회
HCID 16687962Silver hexafluoroantimonate촉매2회

실험 절차

To a 25 ml glass vial equipped with a Teflon® coated stir bar was added 3.06 g (12.8 mmole) of pure of bicyclo[2.2.1]hept-5-ene-exo,exo-2,3-dicarboxylic acid diethyl ester, 2.5 g (12.8 mmole) of t-butylester of norbornene, followed by 15 ml of freshly distilled methylene chloride and 10 ml of methanol, and the solution was degassed under argon atmosphere. A 10 ml glass vial equipped with a Teflon® coated stir bar was charged with 0.0188 g (0.052 mmol) of allylpalladium chloride dimer (to give a monomer to catalyst ratio of 500/1) and 2 ml of methylene chloride. Into another 10 ml glass vial was charged with 0.0357 g (0.104 mmol) of silver hexafluoroantimonate and 2 ml of methylene chloride. The catalyst solution was prepared by mixing the allylpalladium chloride dimer solution with silver hexafluoroantimonate solution inside the dry box. Immediate precipitation of the silver chloride salt was observed, which was filtered, to obtain a clear yellow solution. The active yellow catalyst solution was added to the monomer solution via a syringe at 50° C. and the reaction mixture was allowed to stir for 16 hours at room temperature. No appreciable increase in viscosity was observed and the solution was filtered through a 0.5 μ filter, concentrated using a rotovap. The resulting viscous solution was dissolved in methanol and precipitated into methanol/water mixture to obtain a white solid yield (23%). The molecular weight was observed to be Mn=15,700 g/mole and Mw=32,100 g/mole (GPC in THF, polystyrene standards). 1H NMR indicates the presence of both methyl and t-butyl ester of norbornene. Thermogravimetric analysis (TGA) under nitrogen (heating rate 10° C./min.) showed the polymer to be thermally stable to about 155° C. and then to exhibit approximately 20 wt. % loss by 290° C. (indicating clean loss of the t-butyl groups as isobutylene to afford the homopolymer of 5-norbornene-carboxylic acid) and then degradation of the polymer at around 450° C.

후처리

  1. customthe solution was degassed under argon atmosphere
  2. customA 10 ml glass vial equipped with a Teflon® coated stir bar
  3. customThe catalyst solution was prepared
  4. customImmediate precipitation of the silver chloride salt
  5. filtrationwhich was filtered
  6. customto obtain a clear yellow solution
  7. additionThe active yellow catalyst solution was added to the monomer solution via a syringe at 50° C.
  8. temperatureNo appreciable increase in viscosity
  9. filtrationthe solution was filtered through a 0.5 μ
  10. filtrationfilter
  11. concentrationconcentrated
  12. dissolutionThe resulting viscous solution was dissolved in methanol
  13. customprecipitated into methanol/water mixture
  14. customto obtain a white solid
  15. customyield (23%)
  16. customto be thermally stable to about 155° C.
  17. customby 290° C.

출처 및 근거

ORD 기록
ord-7a48abb5d2af40b98f0a0427a9be1082
출처 데이터셋
uspto-grants-2000_10
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US06136499

반응 노트

이 페이지에서참가 물질실험 절차후처리출처 및 근거반응 노트