홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Isopropanol → UV-328

HRID 441510
인쇄

반응식

HRID 441510 반응식
[OH:1][C:2]1[C:7]([C:8]([CH2:11][CH3:12])([CH3:10])[CH3:9])=[CH:6][C:5]([C:13]([CH2:16][CH3:17])([CH3:15])[CH3:14])=[CH:4][C:3]=1[N:18]=[N:19][C:20]1[CH:25]=[CH:24][CH:23]=[CH:22][C:21]=1[N+:26]([O-])=O.C(O)(C)C.[OH-].[Na+].[N+](C1C=CC=CC=1N=NC1C=CC=CC=1)([O-])=O>[Zn].O>[OH:1][C:2]1[C:7]([C:8]([CH2:11][CH3:12])([CH3:10])[CH3:9])=[CH:6][C:5]([C:13]([CH2:16][CH3:17])([CH3:15])[CH3:14])=[CH:4][C:3]=1[N:18]1[N:26]=[C:21]2[CH:22]=[CH:23][CH:24]=[CH:25][C:20]2=[N:19]1
참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트

참가 물질

7

반응물 4

HCID 3776IsopropanolHCID 14798Sodium HydroxideHCID 1041112-Nitro-2'-hydroxy-3',5'-bis(tert-amyl)azobenzeneHCID 142206Diazene, (nitrophenyl)phenyl-, (E)-

생성물 1

HCID 33263UV-328수율 77.5%

시약·촉매·용매 2

HCID 23994
Zinc
촉매
HCID 962Water용매

반응 조건

온도
60 °C

실험 절차

To a 2000 ml. 3-necked, round-bottomed flask equipped with an agitator, reflux condenser, nitrogen inlet and thermometer were charged 155 grams of 2'-hydroxy-3',5'-di-tert-amyl-2-nitroazobenzene, 119 grams of isopropanol and 80 grams of Amsco mineral spirits. A stream of nitrogen was introduced over the surface of the contents of the flask and the nitrogen atmosphere was then maintained throughout the remainder of the reduction process. 13.7 grams of 50% aqueous sodium hydroxide solution and 222 grams of water were added and the temperature of the contents of the flask were adjusted to 55° C. The ratio of the moles of alkali to moles of o-nitroazobenzene intermediate used was 0.42/1. 104 grams of zinc dust was added in 5 portions over a 2 hour period with the temperature of the flask being held at 55°-60° C. with some slight external cooling. The total concentration of iron impurities from all reactants totalled less than 150 ppm based on zinc used. After all the zinc was added, the temperature was raised to 60° C. and held at this temperature until a spot test indicated no more o-nitroazobenzene intermediate was present. The temperature was then raised to 65° and held there for 4 to 5 hours or until TLC analysis indicated that no more of the N-oxy intermediate was present. 62.6 grams of anhydrous sodium sulfate and 35.6 grams of water were then added, the batch was heated to 70° C. and stirred for 15 minutes. The material was then allowed to stand and separate into three liquid phases plus unreacted zinc dust. The top two layers containing the desired product were transferred to another flask. The remaining aqueous zinc slurry was washed at 65°-70° C. with three successive 16 gram portions of Amsco mineral spirits: isopropanol 50:50. The combined product layers and wash liquids were then washed once at 70° C. with an aqueous hydrochloric acid solution made from 130 grams of water and 40 grams of 32% hydrochloric acid to remove cleavage amine by-products. A second and third wash followed at 70° C. with aqueous hydrochloric acid solutions made each from 65 grams of water and 20 grams of 32% hydrochloric acid. The last wash was essentially colorless. 14 grams of 32% hydrochloric acid and 220 grams of isopropanol were added to the solution of the product. The batch was allowed to crystallize slowly. The solid product form was filtered and washed with isopropanol at 0° C. to give 110 grams of 2-(2-hydroxy-3,5-di-tert-amylphenyl)-2H-benzotriazole with a melting point of 80°-81° C. The yield was 77.5% of theory based on the o-nitroazobenzene intermediate. C. C.

후처리

  1. custom3-necked, round-bottomed flask equipped with an agitator
  2. temperaturereflux condenser, nitrogen inlet
  3. additionA stream of nitrogen was introduced over the surface of the contents of the flask
  4. temperaturethe nitrogen atmosphere was then maintained throughout the remainder of the reduction process
  5. customwere adjusted to 55° C
  6. custombeing held at 55°-60° C. with some slight external cooling
  7. concentrationThe total concentration of iron impurities from all reactants
  8. additionAfter all the zinc was added
  9. temperatureThe temperature was then raised to 65°
  10. addition62.6 grams of anhydrous sodium sulfate and 35.6 grams of water were then added
  11. temperaturethe batch was heated to 70° C.
  12. customseparate into three liquid phases plus unreacted zinc dust
  13. additionThe top two layers containing the desired product
  14. customwere transferred to another flask
  15. washThe remaining aqueous zinc slurry was washed at 65°-70° C. with three successive 16 gram portions of Amsco mineral spirits: isopropanol 50:50
  16. washThe combined product layers and wash liquids
  17. washwere then washed once at 70° C. with an aqueous hydrochloric acid solution
  18. customto remove cleavage amine by-products
  19. washA second and third wash
  20. customfollowed at 70° C. with aqueous hydrochloric acid solutions
  21. washThe last wash
  22. addition14 grams of 32% hydrochloric acid and 220 grams of isopropanol were added to the solution of the product
  23. customto crystallize slowly
  24. filtrationThe solid product form was filtered
  25. washwashed with isopropanol at 0° C.

출처 및 근거

ORD 기록
ord-f8b32e96e9b94768a336b5f8ea63f7d8
출처 데이터셋
uspto-grants-1977_08
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US04041044

반응 노트

이 페이지에서참가 물질반응 조건실험 절차후처리출처 및 근거반응 노트