홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Peracetic Acid → Cyclohexanecarboxylic acid

HRID 610771
인쇄

반응식

HRID 610771 반응식
[CH:1]1([CH:7]=[O:8])[CH2:6][CH2:5][CH2:4][CH2:3][CH2:2]1.CC1C=CC=C(C)[N+]=1[O-:17].C(OO)(=O)C>C(OCCCC)(=O)C.C(OCC)(=O)C>[CH:1]1([C:7]([OH:17])=[O:8])[CH2:6][CH2:5][CH2:4][CH2:3][CH2:2]1
참가 물질실험 절차후처리출처 및 근거반응 노트

참가 물질

6

반응물 3

HCID 6585Peracetic AcidHCID 140832,6-Dimethylpyridine N-oxideHCID 16275Cyclohexanecarboxaldehyde

생성물 1

HCID 7413Cyclohexanecarboxylic acid수율 105%

시약·촉매·용매 2

HCID 8857Ethyl Acetate용매HCID 31272Butyl Acetate용매2회

실험 절차

To a stirred solution of 5.0 g (44.6 mmol) of cyclohexanecarboxaldehyde in n-butyl acetate (45 mL) cooled in a wet-ice bath (ca. 2° C.) was added 5.5 g (44.6 mmol) of 2,6-dimethylpyridine N-oxide (2,6-lutidine N-oxide). To this solution was then added slowly dropwise 24.6 mL (66.9 mmol) of a 23.0 weight percent solution of peracetic acid in ethyl acetate, at a rate slow enough such that the reaction temperature did not exceed 10° C. (ca. 20 min). After the initial exotherm, the temperature returned to 2° C., and the reaction was maintained at this temperature for an additional 4 hours. The cold reaction solution Was then transferred into a separatory funnel, was diluted with n-butyl acetate (50 mL), and was washed with a 1% aqueous solution of sodium thiosulfate (Na2S2O3, 50 mL). The butyl acetate layer was further washed with two portions of water (50 mL each), and the combined water washes were back-extracted with n-butyl acetate (50 ml). The combined butyl acetate layers were extracted with two portions of a 5% aqueous solution of sodium hydroxide (NaOH, 50 mL each). The combined NaOH solutions were acidified to pH=1 with a 10% aqueous solution of hydrochloric acid. The resulting solution was extracted with two portions of dichloromethane (75 mL each), and the extract was dried over anhydrous Na2SO4. The extract was filtered and concentrated in vacuo to give 6.0 g (99%) of cyclohexanecarboxylic acid, containing small levels of unidentified impurities.

후처리

  1. customdid not exceed 10° C.
  2. custom(ca. 20 min)
  3. customreturned to 2° C.
  4. temperaturethe reaction was maintained at this temperature for an additional 4 hours
  5. customThe cold reaction solution Was then transferred into a separatory funnel
  6. washwas washed with a 1% aqueous solution of sodium thiosulfate (Na2S2O3, 50 mL)
  7. washThe butyl acetate layer was further washed with two portions of water (50 mL each)
  8. extractionthe combined water washes were back-extracted with n-butyl acetate (50 ml)
  9. extractionThe combined butyl acetate layers were extracted with two portions of a 5% aqueous solution of sodium hydroxide (NaOH, 50 mL each)
  10. extractionThe resulting solution was extracted with two portions of dichloromethane (75 mL each)
  11. dry with materialthe extract was dried over anhydrous Na2SO4
  12. filtrationThe extract was filtered
  13. concentrationconcentrated in vacuo

출처 및 근거

ORD 기록
ord-f23b1ff0098c40e8b05befe1915f01c6
출처 데이터셋
uspto-grants-1999_12
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US05998660

반응 노트

이 페이지에서참가 물질실험 절차후처리출처 및 근거반응 노트