홈MCP워크벤치Skills
홈워크벤치알림마이페이지
llms.txt · MCP 가이드개인정보처리방침 · 이용약관 · 지원v1.8.3
  1. 홈
  2. /반응

Toluene → 2-[6-(Dibenzothiophen-4-yl)dibenzothiophen-4-yl]dibenzo[f,h]quinoxaline

HRID 628242
인쇄

반응식

HRID 628242 반응식
Cl[C:2]1[CH:11]=[N:10][C:9]2[C:4](=[C:5]3[CH:19]=[CH:18][CH:17]=[CH:16][C:6]3=[C:7]3[CH:15]=[CH:14][CH:13]=[CH:12][C:8]3=2)[N:3]=1.[C:20]1([C:36]2[C:44]3[C:43]4[CH:45]=[CH:46][CH:47]=[CH:48][C:42]=4[S:41][C:40]=3C=CC=2)[C:28]2[C:27]3[CH:29]=[CH:30][CH:31]=[C:32](B(O)O)[C:26]=3[S:25][C:24]=2[CH:23]=[CH:22][CH:21]=1.[C:49]1(C)[CH:54]=CC=C[CH:50]=1.C(=O)([O-])[O-].[K+].[K+]>C([O-])(=O)C.[Pd+2].C([O-])(=O)C.C(O)C>[CH:36]1[C:44]2[C:48]3[CH:47]=[CH:46][CH:45]=[CH:43][C:42]=3[S:41][C:40]=2[C:22]([C:23]2[C:24]3[S:25][C:26]4[C:32]([C:2]5[CH:11]=[N:10][C:9]6[C:4](=[C:5]7[CH:19]=[CH:18][CH:17]=[CH:16][C:6]7=[C:7]7[CH:15]=[CH:14][CH:13]=[CH:12][C:8]7=6)[N:3]=5)=[CH:31][CH:30]=[CH:29][C:27]=4[C:28]=3[CH:54]=[CH:49][CH:50]=2)=[CH:21][CH:20]=1
참가 물질실험 절차후처리출처 및 근거반응 노트

참가 물질

7

반응물 4

HCID 1140TolueneHCID 11430Potassium CarbonateHCID 580194962-Chlorodibenzo[f,h]quinoxalineHCID 1317353434,4'-Bidibenzothiophene-6-boronic acid

생성물 1

HCID 1179404122-[6-(Dibenzothiophen-4-yl)dibenzothiophen-4-yl]dibenzo[f,h]quinoxaline수율 41%

시약·촉매·용매 2

HCID 167845
palladium(II) acetate
촉매
HCID 702Ethanol용매

실험 절차

Into a 200-mL three-neck flask were put 1.6 g (6.1 mmol) of 2-chlorodibenzo[f,h]quinoxaline, 2.5 g (6.1 mmol) of 4,4′-bidibenzothiophene-6-boronic acid, and 0.19 g (0.62 mmol) of tris(2-methylphosphine)phosphine, and the air in the flask was replaced with nitrogen. To this mixture were added 20 mL of toluene, 10 mL of ethanol, and 6.0 mL of an aqueous solution of potassium carbonate (2.0 mol/L). This mixture was degassed by being stirred while the pressure was reduced. To this mixture, 70 mg (0.31 mmol) of palladium(II) acetate was added. This mixture was stirred at 80° C. under a nitrogen stream for 6 hours to precipitate a solid. The precipitated solid was collected by suction filtration. The collected solid was dissolved in approximately 6.0 L of hot toluene, and this solution was suction-filtered through Celite, alumina, and Florisil. The resulting filtrate was concentrated to give a solid. The solid was recrystallized by HPLC to give a white solid. The obtained solid was washed with hot toluene to give 1.5 g of white powder, which was an objective substance, in 41% yield. Synthesis Scheme (b-3) of Step 3 is shown below.

후처리

  1. customInto a 200-mL three-neck flask were put
  2. customThis mixture was degassed
  3. stirringThis mixture was stirred at 80° C. under a nitrogen stream for 6 hours
  4. customto precipitate a solid
  5. filtrationThe precipitated solid was collected by suction filtration
  6. dissolutionThe collected solid was dissolved in approximately 6.0 L of hot toluene
  7. filtrationthis solution was suction-filtered through Celite, alumina, and Florisil
  8. concentrationThe resulting filtrate was concentrated
  9. customto give a solid
  10. customThe solid was recrystallized by HPLC
  11. customto give a white solid
  12. washThe obtained solid was washed with hot toluene

출처 및 근거

ORD 기록
ord-3cd604a422e14644b8a6fde85f48cc13
출처 데이터셋
uspto-grants-2016_04
DOI
10.6084/m9.figshare.5104873.v1
특허 번호
US09312498B2

반응 노트

이 페이지에서참가 물질실험 절차후처리출처 및 근거반응 노트